summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2019-04-25imx8qxp_mek: drop warning due to unused variableStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-04-25imx: support i.MX8QM MEK boardPeng Fan
Add i.MX8QM MEK board support. Included a basic dts, enabled SPL FIT Boot log as below: U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) Normal Boot Trying to boot from MMC2_2 U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) CPU: NXP i.MX8QM RevB A53 at 142933 MHz Model: Freescale i.MX8QM MEK Board: iMX8QM MEK Build: SCFW 9330215b Boot: SD1 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: Error: ethernet@5b040000 address not set. eth-1: ethernet@5b040000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25imx8qxp: mek: enable dm-spl for pmPeng Fan
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled, the bind and probe code in board file could be removed. Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-13Add missing space in commentMarcel Ziswiler
Spotted two missing spaces in comments. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-02imx8mq_evk: README: Make the underline marker fill the whole sentenceFabio Estevam
Let the underline marker "=" fill the whole sentence for better readability. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02imx8mq_evk: README: Fix a typo in the destination pathFabio Estevam
The DDR firmware binaries should be copied to '$(srctree)', so fix a typo. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-04-02imx8mq_evk: README: Need to copy bl31.bin to U-Boot source treeFabio Estevam
After building ATF it is needed to copy the generated bl31.bin file to the U-Boot source tree. Make this step explicit in the instructions. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-03-15armv7: ls102xa: Add workaround for DDR erratum A-008850Alison Wang
Barrier transactions from CCI400 need to be disabled till the DDR is configured, otherwise it may lead to system hang. The patch adds workaround to fix the erratum. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-15board: fsl: lx2160aqds: modify the phy fixup codePankaj Bansal
Now that we are representing the MDIO mux in LX2160AQDS board in producer/consumer terms, the consumer nodes' has been changed. Therefore, modify the device tree fixups according to change in device tree. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-13imx8mq_evk: Add myself as a co-maintainerFabio Estevam
I would like to help maintaining this board. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-03-13mx6sabreauto: README: Adjust the binary name after DM conversionFabio Estevam
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-03-13mx6sabresd: README: Adjust the binary name after DM conversionFabio Estevam
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-03-13imx8mq_evk/README: fix DDR training firmware pathBaruch Siach
Remove a redundant directory level. Reported-by: Ofer Heifetz <ofer.heifetz@valens.com> Tested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-03-13imx8mq_evk/README: add missing firmware extract stepBaruch Siach
Tested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-03-13mx6ul_14x14_evk: Simplify the PMIC register writesFabio Estevam
There is no need to store the values written to the PMIC inside the 'reg' variable. Make it simpler by writing the values directly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-03-04Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
- Enable DHCP as boot-source in distro boot for NXP layerscape platforms - fix register layout for SEC on Layerscape architectures - fixes related to DPAA2 ethernet
2019-03-03board: ls1088a: fix fsl-mc search pathMian Yousaf Kaukab
Path for fsl-mc node in kernel device-tree is /soc/fsl-mc whereas in u-boot it is /fsl-mc. Fix the incorrect search path to fix following error: fdt_fixup_board_enet: ERROR: fsl-mc node not found in device tree (error -1) Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-03board: ls1088a: fix dppa exit when using efi bootMian Yousaf Kaukab
Same issue for ls2080a was fixed by following patch: b7b8410a8f ls2080: Exit dpaa only right before exiting U-Boot Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-03-02powerpc: t104xrdb: Add support of MTA9ADF1G72AZ DDRPeng Ma
T1040RDB has been upgraded to support new DDR ie. MTA9ADF1G72AZ-3G2, 8GB. So adding support of new DDR part by updating board_specific_parameters udimm0. Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19lx2160aqds : Add support for LX2160AQDS platformPankaj Bansal
LX2160AQDS is a development board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [PK: Sqaush patch for "secure boot defconfig" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19board/lx2160a: Add init_func_vid() definitionPriyanka Jain
Add init_func_vid() which calls adjust_vdd() This ensures adjust_vdd() is called via init_sequence_f[] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160: Add secure boot target and enable distro boot.Udit Agarwal
Adds esbc validate command for verification of MC and DPC firmware, along with secure boot defconfig. Also enable distro boot. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> [PK: squash "enable DM support for SATA patch" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19lx2160: Enable support of EMC2305Meenakshi Aggarwal
Enable support for FAN controller EMC2305 for LX2160A RDB board. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> [PK: enable EMC2305 for lx2160rdb] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: emc2305: add support for fan controllerMeenakshi Aggarwal
Add support for fan controller emc2305. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160ardb : Add support for LX2160ARDB platformPriyanka Jain
LX2160ARDB is an evaluation board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> [PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han and re-arrange defconfig] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-15board: mx6sabresd: Remove the enet reset gpio handlingAbel Vesa
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi and get rid of the enet reset gpio handling from the board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabresd: Remove non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabresd board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabreauto: Remove the non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabreauto board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabreauto: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabreauto. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabresd: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabresd. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabreauto: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabreauto - imx6qp-sabreauto - imx6dl-sabreauto Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15board: mx6sabresd: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabresd - imx6qp-sabresd - imx6dl-sabresd Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-05MAINTAINERS: Change fsl-qoriq, mpc85xx, mpc86xx maintainersYork Sun
Change maintainers to Prabhakar Kushwaha for fsl-qoriq, mpc85xx and mpc86xx. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-28imx8mq_evk/README: remove ARCH environment variableBaruch Siach
There is no need to set the ARCH variable when building U-Boot. In fact, the ARCH name in U-Boot is 'arm'. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2019-01-28imx8qxp: mek: update READMEPeng Fan
Update README after we switch to use SPL Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8qxp: mek: default enable SPLPeng Fan
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT. The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK. Note: SPL FIT could not support secure boot chain, because i.MX8/8X only support i.MX container format. This container format has not been upstreamed, so we use FIT for now. When SPL container supported, we could switch to that. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-17armv8: ls2088ardb: Update MAINTAINERSYork Sun
Signed-off-by: York Sun <york.sun@nxp.com> CC: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2019-01-17armv8: ls1088ardb: Update MAINTAINERSYork Sun
Signed-off-by: York Sun <york.sun@nxp.com> CC: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2019-01-17ls1046aqds: Bypass xfi port fixup for KR modeFlorinel Iordache
u-boot makes a fixup for LS1046AQDS board to setup the properties 'fixed-link' and 'phy-connection-type' to 'xgmii' but in case of backplane mode this fixup is not correct because it causes the KR link to fail and so it must be bypassed in order to keep the link in KR mode as it is defined in DTS. Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> [YS: Fix compiling warning] Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17fsl-layerscape: dpaa: fix fsl-mc status in fdt with bootefiMian Yousaf Kaukab
fsl-mc lazyapply command applies dpl from efi_exit_boot_services(). Status of fsl-mc node in working fdt is updated at this stage. However, an efi application like grub may already have copied the fdt. So the updates to fdt done at efi_exit_boot_services() may not be visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply command is used. Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot) Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls2088aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls2088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls2088ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls2088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - remove EL3 specific erratas for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1088aqds: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1088ardb: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-01imx: add i.MX8MQ EVK supportPeng Fan
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to DRAM. The boot log with Arm trusted firmware console enabled: " U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) PMIC: PFUZE100 ID=0x10 Normal Boot Trying to boot from MMC2 NOTICE: Configureing TZASC380 NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty NOTICE: BL31: Built : 09:28:54, Nov 8 2018 lpddr4 swffc start NOTICE: sip svc init U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz Reset cause: POR Model: Freescale i.MX8MQ EVK DRAM: 3 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: Warning: ethernet@30be0000 using MAC address from ROM eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-01imx: imx8qxp_mek: imximage: remove config.hPeng Fan
config.h is not needed, remove it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-12-10Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Add TFA boot flow for some Layerscape platforms Add support for lx2160a SoC [trini: Add a bunch of missing MAINTAINERS entries] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-06board/freescale/vid: Add vdd table for NXP LX2160A SoCPriyanka Jain
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06board/freescale/vid: Add correction for ltc3882 read error.Priyanka Jain
Voltage regulator LTC3882 device has 0.5% voltage read error. So for NXP SoC devices this generally equates to 2mV Update set_voltage_to_LTC for below: 1.Add coorection of upto 2mV in voltage comparison to take care of voltage read error of voltage regulator 2.Add loop max count kept as 100 to avoid infinte loop. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1088ardb_pb: Add support for board detectionPramod Kumar
ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc, board type detection is dynamic at boot time Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-29 20:16:28 +0000