summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2019-01-01imx: add i.MX8MQ EVK supportPeng Fan
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to DRAM. The boot log with Arm trusted firmware console enabled: " U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) PMIC: PFUZE100 ID=0x10 Normal Boot Trying to boot from MMC2 NOTICE: Configureing TZASC380 NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty NOTICE: BL31: Built : 09:28:54, Nov 8 2018 lpddr4 swffc start NOTICE: sip svc init U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz Reset cause: POR Model: Freescale i.MX8MQ EVK DRAM: 3 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: Warning: ethernet@30be0000 using MAC address from ROM eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-01imx: imx8qxp_mek: imximage: remove config.hPeng Fan
config.h is not needed, remove it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-12-10Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Add TFA boot flow for some Layerscape platforms Add support for lx2160a SoC [trini: Add a bunch of missing MAINTAINERS entries] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-06board/freescale/vid: Add vdd table for NXP LX2160A SoCPriyanka Jain
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06board/freescale/vid: Add correction for ltc3882 read error.Priyanka Jain
Voltage regulator LTC3882 device has 0.5% voltage read error. So for NXP SoC devices this generally equates to 2mV Update set_voltage_to_LTC for below: 1.Add coorection of upto 2mV in voltage comparison to take care of voltage read error of voltage regulator 2.Add loop max count kept as 100 to avoid infinte loop. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1088ardb_pb: Add support for board detectionPramod Kumar
ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc, board type detection is dynamic at boot time Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06arm: ls1021a: Add timer_init() in board_init_f for SPLAlison Wang
I2C is used to access DDR SPD in the DDR initialization for SPL. In i2c_write process, get_timer() will be called. In board_init_f for SPL, timer_init() is not called before. The system counter is not enabled and the counter frequency is not set to 12.5MHz in SPL. The parameters for do_div() are zero too. It could not be found until CONFIG_USE_PRIVATE_LIBGCC is enabled in default. When CONFIG_USE_PRIVATE_LIBGCC is enabled, U-Boot will use its own set of libgcc functions. As the parameters for do_div() are zero, __div0 will be called. Then the processor will stay in an endless loop after calling hang(). This patch will add timer_init() in board_init_f for SPL and fix a series of issues it caused. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012afrx: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be loaded by trusted firmware - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [YS: remove unnecessary braces] Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012aqds: fix secure boot compilationRajesh Bhagat
Includes environment.h file in ls1012aqds.c Also, enables pfe validation Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - enable PFE validation for secure boot Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1043aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1043aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1043ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1043ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN and QE address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1046aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1046aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1046ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1046ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2018-11-27spi: Zap CONFIG_HARD_SPIJagan Teki
In legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup. So remove the dead instances of CONFIG_HARD_SPI, and related code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-06mx8mq_evk: README: Delete file introduced by mistakeFabio Estevam
board/freescale/mx8mq_evk/README has been introduced by mistake in commit d0dd73974c61 ("imx: add i.MX8QXP MEK board support") Remove it for now as this should be introduced when mx8mq_evk support is in place. Reported-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2018-10-25Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imxTom Rini
Merged imx8 architecture, fix build for imx8 + warnings
2018-10-22imx: imx8qxp_mek: update to build image in U-BootPeng Fan
Update README Add imximage.cfg Update defconfig to include imximage.cfg Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-10-22imx: add i.MX8QXP MEK board supportPeng Fan
Add i.MX8QXP MEK board support Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver. Added README file. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-10-10driver: net: fsl-mc: Add support of multiple phys for dpmacPankaj Bansal
Till now we have had cases where we had one phy device per dpmac. Now, with the upcoming products (LX2160AQDS), we have cases, where there are sometimes two phy devices for one dpmac. One phy for TX lanes and one phy for RX lanes. to handle such cases, add the support for multiple phys in ethernet driver. The ethernet link is up if all the phy devices connected to one dpmac report link up. also the link capabilities are limited by the weakest phy device. i.e. say if there are two phys for one dpmac. one operates at 10G without autoneg and other operate at 1G with autoneg. Then the ethernet interface will operate at 1G without autoneg. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-09-29Merge tag 'mpc85xx-for-v2018.11-rc1' of git://git.denx.de/u-boot-mpc85xxTom Rini
Use device tree for mpc85xx with binman. Enabled for T2080QDS.
2018-09-27powerpc: dts: Enable device tree support for T2080QDSJagdish Gediya
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL so that device tree can be compiled. Update board README for device tree usage. Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add icid setup supportLaurentiu Tudor
Reuse the existing ICID setup code done for LS1046A smmu enablement and add the equivalent setup for LS1043A chips. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27ls1012afrwy: Add ls1012afrwy revC board support.Pramod Kumar
LS1012AFRWY supports three board revisions. Revision A and B board are collectively identified as revA/B, Revision C board is identifies as revC. Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> [York S: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv7: fsl: remove sata supportPeng Ma
Remove the old implementation in order to enable DM for sata Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-04mx7dsabresd: Add the qspi target to the list of supported defconfigsFabio Estevam
Add an entry for mx7dsabresd_qspi_defconfig to avoid the following warnings: WARNING: no status info for 'mx7dsabresd_qspi' WARNING: no maintainers for 'mx7dsabresd_qspi' Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-09-04imx: imx6ul_evk: Enable DM driver for iMX6UL EVK u-bootYe Li
Convert the codes and configurations to enable DM drivers in u-boot for modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI This patch does not change SPL, so it still uses non-DM driver for UART, GPIO and SD/MMC. Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04imx: imx7d-sdb: Add DM QSPI supportYe Li
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default). To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399 populate R392-R395, R299, R300). So we add new DTS file and new defconfig dedicated for QSPI. Other changes to support the DM QSPI: - Add QSPI node and alias spi0. - Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req conflict - Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to align with kernel and also present the conflict. - Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to "spi-flash" - Remove iomux settings of qspi in board codes which is not needed for DM driver. Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04imx: imx6sx-sabreauto: convert to use DM QSPI driverYe Li
To support DM QSPI driver: - Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string to "spi-flash" and add "num-cs" property. - Enable DM SPI and DM SPI FLASH configurations - Remove iomux settings of qspi1 in board codes which is not needed for DM driver. Signed-off-by: Ye Li <ye.li@nxp.com>
2018-09-04imx: imx6sx-sdb: Enable DM QSPI driverYe Li
To support DM QSPI driver - Add spi0 and spi1 alias for qspi1 and qspi2. - Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string to "spi-flash" and add "num-cs" property. - Enable DM SPI/QSPI relavent configurations - Remove iomux settings of qspi2 in board codes which is not needed for DM driver. - Add sf default settings. So running "sf probe" can detect the flash Signed-off-by: Ye Li <ye.li@nxp.com>
2018-08-10armv8: layerscape: move ns_dev[] define from h to c file.Ran Wang
Move ns_dev[] from header file to C file to avoid compiling warning when header file is included by others. Signed-off-by: Ran Wang <ran.wang_1@nxp.com> [YS: rewrite commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-10armv8: ls1046a: initial icid setup supportLaurentiu Tudor
Add infrastructure for ICID setup and device tree fixup on ARM platforms. This include basic ICID setup for several devices. Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-08-07board: freescale: ls1012ardb: Add command to switch QSPI bankJagdish Gediya
Add command "boot_bank X" to switch the boot bank to either 1 or 2. Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-07-31ls1046ardb: Add qspi_spl variant to the MAINTAINERS fileTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-26armv8: ls1046ardb: Add falcon mode for for QSPI bootYork Sun
A new defconfig is introduced to support SPL boot from QSPI NOR flash. This is to support falcon mode for faster booting into Linux. Signed-off-by: York Sun <york.sun@nxp.com>
2018-07-26armv8: ls2080ardb: update copyright claimAlison Wang
This patch updates the copyright claim for the issues reported by legal review. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-07-25board: constify struct node_info arrayMasahiro Yamada
Add 'const' (also 'static' in some places) to struct node_info arrays to save memory footprint. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-23m68k: m5253evbe: Remove this boardTom Rini
The m5253evbe board has been marked as orphan since June of 2014 and should have been dropped a while ago. Do so now. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board: Kconfig: Re-Arrangement of PPA firmware and header addressesBhaskar Upadhaya
PPA firmware and header address may vary depending upon different boards, configure ppa firmware and header address in board specific Kconfig. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-11Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-05-10board/freescale: Remove invalid fsl email addressesFabio Estevam
These fsl email addresses are no longer valid and they do not have a correspondent nxp.com entry. Remove all invalid fsl email addresses and mark the boards as orphan. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-05-10p1022ds: Change Timur's email addressFabio Estevam
timur@freescale.com is not a valid email for quite some time, so change it to Timur's updated email. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Timur Tabi <timur@tabi.org>
2018-05-09armv8: ls1088: Update 1900MT/s DDR timing to bring consistencyAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09armv8: ls1088aqds: Enable mdio commands on u-boot promptAshish Kumar
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2024-12-28 21:51:06 +0000