summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2013-05-05mx23evk: Fix DDR pin iomux settingsFabio Estevam
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-28imx: iomux-v3: Include PKE and PUE to pad control pull definitionsBenoît Thébaudeau
PUE requires PKE to mean something, as do pull values with PUE, so do not compell users to explicitly use PKE and PUE everywhere. This is also what is done on Linux and what has already been done for i.MX51. By the way, remove some unused pad control definitions. There is no change of behavior. Note that SPI_PAD_CTRL was defined by several boards with a pull value, but without PKE or PUE, which means that no pull was actually enabled in the pad. This might be a bug in those boards, but this patch does not change the behavior, so it just removes the meaningless pull value from those definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-28imx: Homogenize and fix fuse register definitionsBenoît Thébaudeau
IIM: - Homogenize prg_p naming (the reference manuals are not always self-consistent for that). - Add missing SCSx and bank registers. - Fix the number of banks on i.MX53. OCOTP: - Rename iim to ocotp in order to avoid confusion. - Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the reference manual. - Merge the existing spinoff gp1 fuse definition on i.MX6. - Fix the number of banks on i.MX6. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-04-25mx53ard: Move register masks into imx-regs.hFabio Estevam
imx-regs.h is more appropriate location for containing register masks. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2013-04-25mx6qsabresd: Return status when initializing MMCOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-25imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR registerFabio Estevam
Setup CCM_CCOSR register to provide a CKO1 clock frequency of 16.5 MHz. CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c from the mainline kernel. mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for this board as well. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22imx: Add titanium board support (i.MX6 based)Stefan Roese
Titanium is a i.MX6 based board from ProjectionDesign / Barco. This patch adds support for this board with the newly introduced NAND support for i.MX6. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22mx6sl: Add initial support for mx6slevk boardFabio Estevam
mx6slevk board is a development board from Freescale based on the mx6 solo-lite processor. For details about mx6slevk, please refer to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6SLEVK&parentCode=i.MX6SL&fpsp=1 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-13ARM: Fix __bss_start and __bss_end in linker scriptsAlbert ARIBAUD
Commit 3ebd1cbc introduced compiler-generated __bss_start and __bss_end__ and commit c23561e7 rewrote all __bss_end__ as __bss_end. Their merge caused silent and harmless but potentially bug-inducing clashes between compiler- and linker- generated __bss_end symbols. Make __bss_end and __bss_start compiler-only, and create __bss_base and __bss_limit for linker-only use. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12arm: Make all linker scripts compatible with per-symbol sectionsBenoît Thébaudeau
Let all ARM linker scripts handle properly -ffunction-sections and -fdata-sections. This will be useful for future changes in order to create symbol-specific sections in common .S files. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12arm: Remove unused relocate_code() parametersBenoît Thébaudeau
Commit e05e5de7fae5bec79617e113916dac6631251156 made the 2 1st parameters of ARM's relocate_code() useless since it moved the code handling them to crt0.S. So, drop these parameters. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12nand: mxc: Switch NAND SPL to generic SPLBenoît Thébaudeau
This also fixes support for mx31pdk and tx25, which had been broken by commit e05e5de7fae5bec79617e113916dac6631251156. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Scott Wood <scottwood@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-12imx: mx53ard: Add support for NAND FlashBenoît Thébaudeau
Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard. eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this board, which satisfies the 30-ns NF R/W cycle requirement. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-04Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-04-03i.MX6: mx6qsabrelite: README: don't pass chip-select to sf probe commandJavier Martinez Canillas
board/freescale/mx6qsabrelite/README explain a procedure to update the SPI-NOR on the SabreLite board without Freescale manufacturing tool but following this procedure leads to both "sf erase" and "sf write" failing on a mx6qsabrelite board: MX6QSABRELITE U-Boot > sf probe 1 MX6QSABRELITE U-Boot > sf erase 0 0x40000 SPI flash erase failed MX6QSABRELITE U-Boot > sf write 0x10800000 0 0x40000 SPI flash write failed This is because the chip-select 1 is wrong and the correct value is 0x7300. Since commit c1173bd0 ("sf command: allow default bus and chip selects") the chip-select and bus arguments for the sf probe command are optional so let's just remove it and use "sf probe" instead. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
2013-04-03mx6: Fix get_board_rev() for the mx6 solo caseFabio Estevam
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev() returns 0x62xxx, which is not a value understood by the VPU (Video Processing Unit) library in the kernel and causes the video playback to fail. The expected values for get_board_rev are: 0x63xxx: For mx6quad/dual 0x61xxx: For mx6dual-lite/solo So adjust get_board_rev() accordingly and make it as weak function, so that we do not need to define it in every mx6 board file. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-04-03mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a boardAbbas Raza
Maximum bus width supported by some i.MX6 boards is not 8bit like others. In case where both host controller and card support 8bit transfers, they agree to communicate on 8bit interface while some boards support only 4bit interface. Due to this reason the mmc 8bit default mode fails on these boards. To rectify this, define maximum bus width supported by these boards (4bit). If max_bus_width is not defined, it is 0 by default and 8bit width support will be enabled in host capabilities otherwise host capabilities are modified accordingly. It is tested with a MMCplus card. Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com> cc: stefano Babic <sbabic@denx.de> cc: Andy Fleming <afleming@gmail.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2013-04-03mx6qsabrelite: README: No need to pass 'u-boot.imx'Fabio Estevam
The u-boot.imx binary is generated by default, so no need to pass it in the 'make' line. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-03mx6qsabre{sd,auto}: Add boot mode selectOtavio Salvador
Adds support for 'bmode' command which let user to choose where to boot from; this allows U-Boot to load system from another storage without messing with jumpers. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03mx6qsabresd: Fix card detection for invalid card id caseOtavio Salvador
This changes the code so in case an unkown value is passed it will return as invalid. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-04-03mx6qsabresd: Document the mapping of USDHC[2-4]Otavio Salvador
This documents the SD card identifier so it is easier for user to spot which card number will be used, if need. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-03-18Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Albert's rework of the linker scripts conflicted with Simon's making everyone use __bss_end. We also had a minor conflict over README.scrapyard being added to in mainline and enhanced in u-boot-arm/master with proper formatting. Conflicts: arch/arm/cpu/ixp/u-boot.lds arch/arm/cpu/u-boot.lds arch/arm/lib/Makefile board/actux1/u-boot.lds board/actux2/u-boot.lds board/actux3/u-boot.lds board/dvlhost/u-boot.lds board/freescale/mx31ads/u-boot.lds doc/README.scrapyard include/configs/tegra-common.h Build tested for all of ARM and run-time tested on am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
2013-03-15Replace __bss_end__ with __bss_endSimon Glass
Note this is a tree-wide change affecting multiple architectures. At present we use __bss_start, but mostly __bss_end__. This seems inconsistent and in a number of places __bss_end is used instead. Change to use __bss_end for the BSS end symbol throughout U-Boot. This makes it possible to use the asm-generic/sections.h file on all archs. Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-03-12Refactor linker-generated arraysAlbert ARIBAUD
Refactor linker-generated array code so that symbols which were previously linker-generated are now compiler- generated. This causes relocation records of type R_ARM_ABS32 to become R_ARM_RELATIVE, which makes code which uses LGA able to run before relocation as well as after. Note: this affects more than ARM targets, as linker- lists span possibly all target architectures, notably PowerPC. Conflicts: arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds arch/arm/cpu/armv7/omap-common/u-boot-spl.lds board/ait/cam_enc_4xx/u-boot-spl.lds board/davinci/da8xxevm/u-boot-spl-da850evm.lds board/davinci/da8xxevm/u-boot-spl-hawk.lds board/vpac270/u-boot-spl.lds Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12arm: make __bss_start and __bss_end__ compiler-generatedAlbert ARIBAUD
Turn __bss_start and __bss_end__ from linker-generated to compiler-generated symbols, causing relocations for these symbols to change type, from R_ARM_ABS32 to R_ARM_RELATIVE. This should have no functional impact, as it affects references to __bss_start and __bss_end__ only before relocation, and no such references are done. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-09mpc512x: use common code for clock setting for all mpc512x boardsAnatolij Gustschin
Only define enabled clocks in the config file and enable the clocks in common code. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Wolfgang Denk <wd@denx.de>
2013-03-09mpc512x: use common code for CSx configurationAnatolij Gustschin
Remove CSx configurations from board code and only define required CSx macros in the board config file to configure chip select windows and parameters. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Wolfgang Denk <wd@denx.de>
2013-03-07mx6: Provide a structure for accessing HDMI registersFabio Estevam
Provide a structure for accessing HDMI registers, so that we can use proper read/write accessors. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-03-07mx23evk: Adjust DRAM control register to use full 128MB of RAMOtavio Salvador
Adjust HW_DRAM_CTL14 to enable the chip selects to allow usage of full 128MB of RAM. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2013-03-07i.MX6: consolidate pad names for multi-CPU boardsEric Nelson
Rename all i.MX6 pad declarations to MX6_PAD_x, so a board may support either i.MX6Quad/Dual (MX6Q) or i.MX6Dual-Lite/Solo (MX6DL) by including the proper header. Boards mx6qarm2, mx6qsabreauto, mx6qsabrelite, and mx6qsabresd only support MX6Q, so they include mx6q_pins.h. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-03-07i.MX6: mx6qsabrelite: indent with tabsEric Nelson
This patch has no functional changes and simply replaces leading spaces with tabs. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-02-23Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
2013-02-12Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-02-12imx: mx6q DDR3 init: Benefit from available CL = 7Benoît Thébaudeau
All the users of mx6q_4x_mt41j128.cfg (DDR3-1333H Micron MT41J128M16HA-15E or SK hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and DDR3-1600K Micron MT41K128M16JT-125:K for i.MX6 SABRE SD) support the optional down binning to DDR3-1066F (CL = 7, CWL = 6), which is possible at 532 MHz, so use it. In these conditions: tRCD(min) = 13.125 ns tRP(min) = 13.125 ns tRC(min) = max(tRAS(min, DDR3-1333H), tRAS(min, DDR3-1600K)) + tRP(min) tRAS(min, DDR3-1333H) = 36 ns tRAS(min, DDR3-1600K) = 35 ns MMDC1_MDCFG0.tCL should be set to 7 nCK, encoded as 0x4 in the bit-field MMDC1_MDCFG0[3:0]. MR0.CL should be set as in MMDC1_MDCFG0.tCL, i.e. to 7 nCK, which is encoded as 0x6 in MRS.LMR.MR0.{A6:A4, A2} and MMDC1_MDSCR[22:20, 18]. MMDC1_MDCFG1.tCWL should be set to 6 nCK, encoded as 0x4 in the bit-field MMDC1_MDCFG1[2:0]. MMDC1_MDCFG1.tRCD should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded as 0x6 in the bit-field MMDC1_MDCFG1[31:29]. MMDC1_MDCFG1.tRP should be set to 13.125 ns, which is 7 nCK at 532 MHz, encoded as 0x6 in the bit-field MMDC1_MDCFG1[28:26]. MMDC1_MDCFG1.tRC should be set to 49.125 ns, which is 27 nCK at 532 MHz, encoded as 0x1A in the bit-field MMDC1_MDCFG1[25:21]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-02-12imx: mx6q DDR3 init: Fix MR0.PPDBenoît Thébaudeau
MR0.PPD should be set as in MMDCx_MDPDC.SLOW_PD, i.e. to fast-exit mode, which is encoded as 1 in MRS.LMR.MR0.A12 and MMDCx_MDSCR[28]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-02-12imx: mx6q DDR3 init: Fix RST_to_CKEBenoît Thébaudeau
MMDC1_MDOR.RST_to_CKE should be set to 500 µs according to the JEDEC specification for DDR3. With a cycle of 15.258 µs, this gives 33 cycles encoded as 0x23 for the bit-field MMDC1_MDOR[5:0]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-02-12imx: mx6q DDR3 init: Fix SDE_to_RSTBenoît Thébaudeau
MMDC1_MDOR.SDE_to_RST should be set to 200 µs according to the JEDEC specification for DDR3. With a cycle of 15.258 µs, this gives 14 cycles encoded as 0x10 for the bit-field MMDC1_MDOR[13:8]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-02-12imx: mx6q DDR3 init: Fix tXPRBenoît Thébaudeau
MMDC1_MDOR.tXPR should be set as specified for the JEDEC DDR3 timing tXPR. For all DDR3 speed bins: tXPR(min) = max(5 nCK, tRFC(min) + 10 ns) tRFC(2 Gb) = 160 ns All the users of mx6q_4x_mt41j128.cfg have a 2-Gb density (Micron MT41J128M16HA-15E or SK hynix H5TQ2G63BFR-H9C for i.MX6Q SABRE Lite, and Micron MT41K128M16JT-125:K for i.MX6 SABRE SD). Hence, MMDC1_MDOR.tXPR should be set to max(5 nCK, 170 ns), which is 170 ns and 91 nCK at 532 MHz, encoded as 0x5A in the bit-field MMDC1_MDOR[23:16]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-02-12imx: mx6q DDR3 init: Fix tMRDBenoît Thébaudeau
MMDC1_MDCFG1.tMRD should be set to max(tMRD, tMOD) for DDR3. For all DDR3 speed bins: tMRD(min) = 4 nCK tMOD(min) = max(12 nCK, 15 ns) Hence, MMDC1_MDCFG1.tMRD should be set to max(12 nCK, 15 ns), which is 12 nCK at 532 MHz, encoded as 0xB in the bit-field MMDC1_MDCFG1[8:5]. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-02-04ppc: Move lbc_clk and cpu to arch_global_dataSimon Glass
Move these fields into arch_global_data and tidy up. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Update for bsc9132qds.c, b4860qds.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-01-30board/common: Add support for QIXIS read/write using i2cPrabhakar Kushwaha
QIXIS FPGA is accessable via both i2c and flash controller. Only flash controller access is supported. Add support of i2c based access. It is quite useful in the scenario where either flash controller path is broken or not present. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/85xx: Add BSC9132QDS supportPrabhakar Kushwaha
BSC9132QDS is a Freescale reference design board for BSC9132 SoC. BSC9132 SOC is an integrated device that targets the evolving Microcell, Picocell, and Enterprise-Femto base station market subsegments. It combines Power Architecture e500v2 and DSP StarCore SC3850 core technologies with MAPLE-B2F baseband acceleration processing elements. BSC9132QDS Overview -------------------- 2Gbyte DDR3 (on board DDR), Dual Ranki 32Mbyte 16bit NOR flash 128Mbyte 2K page size NAND Flash 256 Kbit M24256 I2C EEPROM 128 Mbit SPI Flash memory SD slot USB-ULPI eTSEC1: Connected to SGMII PHY eTSEC2: Connected to SGMII PHY PCIe CPRI SerDes I2C RTC DUART interface: supports one UARTs up to 115200 bps for console display Apart from the above it also consists various peripherals to support DSP functionalities. This patch adds support for mainly Power side functionalities and peripherals Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/p2041: add RCW file for P2041RDBValentin Longchamp
All the dev boards of Freescale's QorIQ family have a RCW that is supported by the u-boot.pbl build target. This patch adds one for the P2041 dev board. This RCW is suitable for the RAMBOOT_PBL scenarios and was tested on the P2041RDB booting from the eSPI NOR Flash (P2041RDB_SPIFLASH config). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/t4240qds: Print FPGA detail versionPrabhakar Kushwaha
Qixis FPGA has tag data contains image name and build date. It is helpful to identify the FPGA image precisely. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/t4240qds: Add support to dump switch settings on t4240qds boardShaveta Leekha
This function is called by "qixis_reset switch" command and switch settings are calculated from qixis FPGA registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/b4860qds: Add support to dump switch settings on b4860qds boardShaveta Leekha
This function is called by "qixis_reset switch" command and switch settings are calculated from FPGA/qixis registers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/qixis: enable qixis dump command and add switch dumping commandShaveta Leekha
Remove #ifdef so that "qixis dump" command is always available Add "qixis_reset switch" command to dump switch settings Qixis doesn't have 1:1 switch mapping. We need to reverse engineer from registers to figure out switch settings. Not all bits are available. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30powerpc/b4860qds: Added Support for B4860QDSYork Sun
B4860QDS is a high-performance computing evaluation, development and test platform supporting the B4860 QorIQ Power Architecture processor. B4860QDS Overview ------------------ - DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB of memory in two ranks of 2 GB. - DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank. - SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch VSC3316 - SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308 - USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode. - B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable. - A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for AMC mode. - The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The RCW source is set by appropriate DIP-switches: - 16-bit NOR Flash / PROMJet - QIXIS 8-bit NOR Flash Emulator - 8-bit NAND Flash - 24-bit SPI Flash - Long address I2C EEPROM - Available debug interfaces are: - On-board eCWTAP controller with ETH and USB I/F - JTAG/COP 16-pin header for any external TAP controller - External JTAG source over AMC to support B2B configuration - 70-pin Aurora debug connector - QIXIS (FPGA) logic: - 2 KB internal memory space including - IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1, 2 and RTCCLK. - Two 8T49N222A SerDes ref clock devices support two SerDes port clocks - total four refclk, including CPRI clock scheme Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30board/freescale/common:Add support of QTAG registerPrabhakar Kushwaha
QIXIS FPGA's QIXIS Tag Access register (QTAG) defines TAG, VER, DATE, IMAGE fields. These fields have FPGA build version, image name and build date information. Add support to parse these fields to have complete FPGA image information. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-29 14:07:34 +0000