summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2017-05-18imx: mx7dsabresd: switch to DM USBPeng Fan
Switch to use DM USB. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2017-05-18imx: mx7dsabresd: reset ENET_RST_BPeng Fan
Reset ENET_RST_B to make ENET function stable. Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds to ENET_RST_B. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-05-18imx: mx7dsabresd: enable more DM driversPeng Fan
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled. So needs to enable them together. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-05-18mx6sabresd: Remove non-SPL targetsFabio Estevam
Now that mx6sabresd_spl_defconfig can be used to boot all mx6sabresd variants, the non-SPL targets can be safely removed. Signed-off-by: Fabio Estevam <fabio.estvam@nxp.com>
2017-05-18mx6sabresd: Add SPL support for the mx6dl variantFabio Estevam
Add support for the mx6dlsabresd board in SPL. Retrieved the DCD table from: board/freescale/mx6sabresd/mx6dlsabresd.cfg (NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga) Flashed SPL and u-boot.img to an SD card and could successfully boot it on mx6q, mx6qp and mx6dl sabresd boards. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-18mx6sabresd: Prepare for supporting MX6DLFabio Estevam
Currently only MX6Q/QP sabresd boards are supported in SPL. In order to also support MX6DL we need to convert to using IOMUX_PADS and SETUP_IOMUX_PADS macros. Other than that move the <asm/arch/mx6-ddr.h> header inclusion to the SPL code block in order to avoid build error. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-15i2c: powerpc: Remove use of CONFIG_HARD_I2CSimon Glass
Drop use of this long-deprecated option for powerpc. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-15i2c: Drop use of CONFIG_I2C_HARDSimon Glass
This option is pretty old. It predates CONFIG_SYS_I2C which is itself deprecated in favour of driver model. Disable it for all boards. Also drop I2C options which depend on this. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-12m5253demo: Fix static variable in non-static inline function warningTom Rini
The function 'spin_wheel' is declared as inline, but not static and thus we see warnings that 'w' and 'p' are declared static in a non-static inline function. Correct this by marking spin_wheel as static inline. Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-12mx6ul_14x14_evk: Fix unused variable warningTom Rini
The variable usdhc1_pads is only referenced during SPL builds, add a guard. Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-12mx6slevk: Fix unused variable warningTom Rini
The variable usdhc1_pads is only referenced during SPL builds, add a guard. Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-05-09p1_p2_rdb: Fix unused variable warningTom Rini
With gcc-6 we see a warning that sysclk_tbl is defined but unused, so remove it. Cc: York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-30Convert CONFIG_CMD_BLOB to KconfigSimon Glass
This converts the following to Kconfig: CONFIG_CMD_BLOB Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add imply CMD_BLOB under CHAIN_OF_TRUST] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-24armv8: layerscape: Fix DDR size calcuation for SPL buildYork Sun
Commit 088454cd dropped return value from initram(), setting gd->ram_size directly. Three boards were missed for SPL boot. Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-24armv8: ls1046aqds: Integrate FSL PPAHou Zhiqiang
The PPA is a EL3 firmware, which support PSCI, hotplug, power-management features etc. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-24armv8: ls1043aqds: Integrate FSL PPAHou Zhiqiang
The PPA is a EL3 firmware, which support PSCI, hotplug, power-management features etc. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-24armv8: ls2080ardb: Add phy number for serdes1 protocol 0x4bSantan Kumar
Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-24arm: ls1021atwr: Enable RGMII TX/RX clock internal delay for AR8033Alison Wang
Since commit ce412b7, RGMII TX clock internal delay is not enabled for AR8033 unconditionally. On LS1021ATWR board, the third port eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to be enabled. This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX clock internal delay for AR8033 on the third port. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17powerpc/board/t1024rdb: enable board-level reset when issuing reset commandShengzhou Liu
As board-specific reset logic, it needs to issue reset signal via CPLD when issuing 'reset' command in u-boot, this patch solves the issue of reset command not working on T1024RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv7: ls1021a: Drop macro CONFIG_LS102XAYork Sun
Use CONFIG_ARCH_LS1021A instead. Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17arm: ls1046ardb: Add SD secure boot targetRuchika Gupta
- Add SD secure boot target for ls1046ardb. - Change the u-boot size defined by a macro for copying the main U-Boot by SPL to also include the u-boot Secure Boot header size as header is appended to u-boot image. So header will also be copied from SD to DDR. - CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM (128K) where 32K are reserved for use by boot ROM and 6K for the header. - Reduce the size of CAAM driver for SPL Blobification functions and descriptors, that are not required at the time of SPL are disabled. Further error code conversion to strings is disabled for SPL build. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17arm: ls1043ardb: Add NAND secure boot targetRuchika Gupta
Add NAND secure boot target for ls1043ardb. - Change the u-boot size defined by a macro for copying the main U-Boot by SPL to also include the u-boot Secure Boot header size as header is appended to u-boot image. So header will also be copied from SD to DDR. - MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript from NAND to DDR. Offsets for Bootscript on NAND and DDR have been also defined. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17arm: ls1043ardb: Add SD secure boot targetRuchika Gupta
- Add SD secure boot target for ls1043ardb. - Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream ID and corresponding stream ID in SMMU. - Change the u-boot size defined by a macro for copying the main U-Boot by SPL to also include the u-boot Secure Boot header size as header is appended to u-boot image. So header will also be copied from SD to DDR. - CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM (128K) where 32K are reserved for use by boot ROM and 6K for secure boto header. - Error messages during SPL boot are limited to error code numbers instead of strings to reduce the size of SPL image. Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv8: LS1012ARDB: Add QSPI Secure Boot targetVinitha Pillai-B57223
Add QSPI Secure Boot target to enable chain of trust Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv8: LS1046ARDB: Add QSPI Secure Boot targetVinitha Pillai-B57223
Add QSPI Secure Boot target. Also enable sec init. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv8: LS1046AQDS: Add NOR Secure Boot TargetSumit Garg
Add NOR secure boot target. Also enable sec init. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv8: ls1046ardb: SPL size reductionSumit Garg
Using changes in this patch we were able to reduce approx 4k size of u-boot-spl.bin image. Following is breif description of changes to reduce SPL size: 1. Changes in board/freescale/ls1046ardb/Makefile to remove compilation of eth.c and cpld.c in case of SPL build. 2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep only ddr_init and board_early_init_f funcations in case of SPL build. 3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver specific macros due to which static data was being compiled in case of SPL build. 4. Disable MMC driver from bieng compiled in case of SPL NAND build and NAND driver from bieng compiled in case of SPL MMC build. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-17armv8: ls1043ardb: SPL size reductionSumit Garg
Using changes in this patch we were able to reduce approx 10k size of u-boot-spl.bin image. Following is breif description of changes to reduce SPL size: 1. Changes in board/freescale/ls1043ardb/Makefile to remove compilation of eth.c and cpld.c in case of SPL build. 2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep only ddr_init and board_early_init_f funcations in case of SPL build. 3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver specific macros due to which static data was being compiled in case of SPL build. 4. Disable MMC driver from bieng compiled in case of SPL NAND build and NAND driver from bieng compiled in case of SPL MMC build. 5. Remove I2C driver support from SPL in case of LS1043ARDB. Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-04-14Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2017-04-14Convert CONFIG_FSL_DCU_FB to KconfigSanchayan Maity
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB and convert it to Kconfig. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13board_f: Rename initdram() to dram_init()Simon Glass
This allows us to use the same DRAM init function on all archs. Add a dummy function for arc, which does not use DRAM init here. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Dummy function on nios2] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-12arm: freescale: Rename initdram() to fsl_initdram()Simon Glass
This function name shadows a global name but is in fact different. This is very confusing. Rename it to help with the following refactoring. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-12mx6sabresd: README: Add eMMC boot configurationBreno Lima
Explain how to flash the eMMC and how to boot from it. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-05board_f: Drop setup_dram_config() wrapperSimon Glass
By making dram_init_banksize() return an error code we can drop the wrapper. Adjust this and clean up all implementations. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05board_f: Drop return value from initdram()Simon Glass
At present we cannot use this function as an init sequence call without a wrapper, since it returns the RAM size. Adjust it to set the RAM size in global_data instead, and return 0 on success. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05board_f: Drop board_type parameter from initdram()Simon Glass
It looks like only cm5200 and tqm8xx use this feature, so we don't really need it in generic code. Drop it and have the users access gd->board_type directly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05board_f: powerpc: Use timer_init() instead of init_timebase()Simon Glass
There is no good reason to use a different name on PowerPC. Change it to timer_init() like the others. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Stefan Roese <sr@denx.de>
2017-03-28board: freescale: ls2080a/ls2088a: Enable PPASantan Kumar
Enable PPA on LS2080A, LS2088A boards: -LS2080ARDB, LS2080AQDS -LS2088ARDB, LS2088AQDS Signed-off-by: Santan Kumar <santan.kumar@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28fsl: Secure Boot: Enable IE (Key extention) FeatureUdit Agarwal
For validating images from uboot (Such as Kernel Image), either keys from SoC fuses can be used or keys from a verified table of public keys can be used. The latter feature is called IE Key Extension Feature. For Layerscape Chasis 3 based platforms, IE table is validated by Bootrom and address of this table is written in scratch registers 13 and 14 via PBI commands. Following are the steps describing usage of this feature: 1) Verify IE Table in ISBC phase using keys stored in fuses. 2) Install IE table. (To be used across verification of multiple images stored in a static global structure.) 3) Use keys from IE table, to verify further images. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28fsl-layerscape/ppa: cleanup ppa.hHou Zhiqiang
Moved the ifdef into ppa.h and removed the duplicated macros. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28armv8: LS2080A: Move sec_init to board_initUdit Agarwal
Moves sec_init to board_init rather than in misc_init function beacuse PPA will be initialised in board_init function and for PPA validation sec_init has to be done prior to PPA init. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-20imx: mx6slevk: enable more DM driversPeng Fan
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO enabled. So needs to enable them together. DM FEC and SPI are not enabled, but they use gpio in board code. So use gpio_request first to request the gpio, because DM_GPIO is enabled. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-19Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/bk4r1_defconfig configs/colibri_vf_defconfig configs/pcm052_defconfig include/configs/colibri_vf.h include/configs/pcm052.h
2017-03-19ARM: vf610: move to standard arch/board approachStefan Agner
Move Freescale/NXP Vybrid to a standard arch/board approach, similar to what has been done to i.MX 6 earlier in commit 89ebc82137be ("ARM: mx6: move to a standard arch/board approach"). Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-17imx: imx7ulp: add EVK board supportPeng Fan
Add EVK board support. Add the evk dts file. LOG: U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800) CPU: Freescale i.MX7ULP rev1.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial@402D0000 Out: serial@402D0000 Err: serial@402D0000 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-14armv8: fsl-layerscape: Add vid support for LS2080AQDSPriyanka Jain
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Arpit Goel <arpit.goel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: fsl-lsch3: Update VID supportPriyanka Jain
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like LS2088A, LS2080A differs from existing logic. -VDD voltage array is different -Registers are different -VDD calculation logic is different Add new function adjust_vdd() for LSCH3 compliant SoCs Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Arpit Goel <arpit.goel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: layerscape: Update early MMU for DDR after initializationYork Sun
In early MMU table, DDR has to be mapped as device memory to avoid speculative access. After DDR is initialized, it needs to be updated to normal memory to allow code execution. To simplify the code, dram_init() is moved into a common file as a weak function. Signed-off-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: layerscape: Rewrite memory reservationYork Sun
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved at the end of DDR. DDR is spit into two or three banks. This patch reverts commit aabd7ddb and simplifies the calculation of reserved memory, and moves the code into common SoC file. Secure memory is carved out first. DDR bank size is reduced. Reserved memory is then allocated on the top of available memory. U-Boot still has access to reserved memory as data transferring is needed. Device tree is fixed with reduced memory size to hide the reserved memory from OS. The same region is reserved for efi_loader. Signed-off-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-28 18:34:50 +0000