| Age | Commit message (Collapse) | Author |
|---|
|
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
|
|
This allows a watchdog reset to start the ROM's
usb/serial downloader, or boot from an sdcard.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
This allows a watchdog reset to start the ROM's
usb downloader, or boot from an sdcard.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
Move mx6 specific defines to arch-mx6 directory.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
This gets us rid of duplication of the same file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
On this board, the console is always set to the serial line.
Do not allow to overwrite it when video is enabled.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
LAW init is skipped in the SPL payload because it's assumed that the SPL
has taken care of it -- so make sure the SPL loads all the LAWs as is
done on other boards.
This bug was introduced by:
commit 4589728e214958a4e6e011a081a68d360c49d7a5
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Fri Nov 11 08:14:53 2011 -0600
powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND
Size grew a bit so nand-spl didn't fit in 4k, reduce done by removing
LAW entries not needed during SPL phase.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
enum board_slots contained six values, where SLOT1 == 1, SLOT2 == 2, and
so on. This is pointless, so remove it. Also move the lane_to_slot[]
array to the top of the file so that it can be used by other functions.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
In order to figure out which SerDes lane a given Fman port is connected
to, we need a function that maps the fm_port namespace to the srds_prtcl
namespace.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Using the raw value of 0x80000000 directly in the code can
lead to "count the zeros" bugs like that fixed in commit
718e9d13b98 ("MPC85xxCDS: Fix missing LCRR_DBYP bits for
66-133MHz LBC")
Change all existing raw values to use the symbolic value of
LCRR_DBYP instead.
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
There was an extra 0 in front of the value we were using to mask,
remove it to improve the code.
Also fix the value written to ddr_sdram_cfg to set the bus width
properly to 16 bits
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Provides a tool to build boot Image for PBL(Pre boot loader) which is
used on Freescale CoreNet SoCs, PBL can be used to load some instructions
and/or data for pre-initialization. The default output image is u-boot.pbl,
for more details please refer to doc/README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.
NOTE: Because the slave can not erase, write master's NOR flash by
PCIE interface, so it can not modify the ENV parameters stored
in master's NOR flash using "saveenv" or other commands.
environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Put the slave's ucode and ENV into it's own memory space.
4. Normally boot from local NOR flash.
5. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the slave module, need to finish these processes:
1. Set the boot location to one PCIE interface by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID of one PCIE for the boot.
4. Set a specific TLB entry in order to fetch ucode and ENV from
master.
5. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
6. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
1. Updated the README.srio-boot-corenet to add descriptions about
boot from PCIE, and change the name to
README.srio-pcie-boot-corenet.
2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
"xxxx_SRIO_PCIE_BOOT", and the image builded with
"xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
from PCIE.
3. Updated other macros and documents if needed to add information
about boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.
For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.
Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.
Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.
Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.
Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This includes bus recovery support.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
ARM: cache: Move the cp15 CR register read before flushing the cache.
ARM: introduce arch_early_init_r()
PXA: Enable CONFIG_PREBOOT on zipitz2
ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
No need to define CONFIG_ARCH_CPU_INIT.
add new board vl_ma2sc
MTD: SPEAr SMI: Add write support for length < 4 bytes
i2c: designware_i2c.c: Add support for the "i2c probe" command
rtc/m41t62: Add support for M41T82 with HT (Halt Update)
SPL: ARM: spear: Add SPL support for SPEAr600 platform
Makefile: Add u-boot.spr build target (SPEAr)
SPL: ARM: spear: Remove some objects from SPL build
SPL: lib/Makefile: Add crc32.c to SPL build
SPL: common/Makefile: Add image.c to SPL build
arm: Don't use printf() in SPL builds
GPIO: Add SPEAr GPIO driver
net: Multiple updates/enhancements to designware.c
cleanup/SPEAr: Define configuration flags more elegantly
cleanup/SPEAr: Remove unnecessary parenthesis
SPEAr: Correct SoC ID offset in misc configuration space
SPEAr: explicitly select clk src for UART
SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
SPEAr: Enable dcache for fast file transfer
SPEAr: Enable autoneg for ethernet
SPEAr: Enable udc and usb-console support only for usbtty configuration
SPEAr: Enable usb device high speed support
SPEAr: Initialize SNOR in early_board_init_f
SPEAr: Change the default environment variables
SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
SPEAr: Add configuration options for spear3xx and spear6xx boards
SPEAr: Add basic arch related support for SPEAr SoCs
SPEAr: Add interface information in initialization
SPEAr: Add macb driver support for spear310 and spear320
SPEAr: Configure network support for spear SoCs
SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
SPEAr: Eliminate dependency on Xloader table
SPEAr: Fix ARM relocation support
st_smi: Fixed page size for Winbond W25Q128FV flash
st_smi: Change timeout loop implementation
st_smi: Fix bug in flash_print_info()
st_smi: Change the flash probing method
st_smi: Removed no needed dependency on ST_M25Pxx_ID
st_smi: Fix smi read status
st_smi: Move status register read before modifying ctrl register
st_smi: Read status until timeout happens
st_smi: Enhance the error handling
st_smi: Change SMI timeout values
st_smi: Return error in case TFF is not set
st_smi: Add support for SPEAr SMI driver
mtd/NAND: Remove obsolete SPEAr specific NAND drivers
SPEAr: Configure FSMC driver for NAND interface
mtd/NAND: Add FSMC driver support
arm/km: remove calls to kw_gpio_* in board_early_init_f
arm/km: add implementation for read_dip_switch
arm/km: support the 2 PCIe fpga resets
arm/km: skip FPGA config when already configured
arm/km: redefine piggy 4 reg names to avoid conflicts
arm/km: cleanup km_kirkwood boards
arm/km: enable BOCO2 FPGA download support
arm/km: remove portl2.h and use km_kirkwood instead
arm/km: convert mgcoge3un target to km_kirkwood
arm/km: add kmcoge5un board support
arm/km: add kmnusa board support
arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
cm-t35: fix incorrect NAND_ECC layout selection
ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
ARM: OMAP4/5: Move USB pads to essential list.
ARM: OMAP4/5: Move USB clocks to essential group.
ARM: OMAP4/5: Move gpmc clocks to essential group.
ARM: OMAP4+: Move external phy initialisations to arch specific place.
omap4: Use a smaller M,N couple for IVA DPLL
da850/omap-l138: Enable auto negotiation in RMII mode
omap: am33xx: accomodate input clocks other than 24 Mhz
omap: emif: fix bug in manufacturer code test
omap: emif: deal with rams that return duplicate mr data on all byte lanes
OMAP4+: Force DDR in self-refresh after warm reset
OMAP4+: Handle sdram init after warm reset
ARM: OMAP3+: Detect reset type
arm: bugfix: Move vector table before jumping relocated code
Kirkwood: Add support for Ka-Ro TK71
arm/km: use spi claim bus to switch between SPI and NAND
arm/kirkwood: protect the ENV_SPI #defines
ARM: don't probe PHY address for LaCie boards
lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
lacie_kw: fix SDRAM banks number for net2big_v2
Kirkwood: add lschlv2 and lsxhl board support
net: add helper to generate random mac address
net: use common rand()/srand() functions
lib: add rand() function
kwboot: boot kirkwood SoCs over a serial link
kw_spi: add weak functions board_spi_claim/release_bus
kw_spi: support spi_claim/release_bus functions
kw_spi: backup and reset the MPP of the chosen CS pin
kirkwood: fix calls to kirkwood_mpp_conf
kirkwood: add save functionality kirkwood_mpp_conf function
km_arm: use filesize for erase in update command
arm/km: enable mii cmd
arm/km: remove CONFIG_RESET_PHY_R
arm/km: change maintainer for mgcoge3un
arm/km: fix wrong comment in SDRAM config for mgcoge3un
arm/km: use ARRAY_SIZE macro
arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
arm/km: add piggy mac adress offset for mgcoge3un
arm/km: add board type to boards.cfg
AT91SAM9*: Change kernel address in dataflash to match u-boot's size
ATMEL/PIO: Enable new feature of PIO on Atmel device
ehci-atmel: fix compiler warning
AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
Atmel : usb : add EHCI driver for Atmel SoC
Fix: AT91SAM9263 nor flash usage
Fix: broken boot message at serial line on AT91SAM9263-EK board
i.MX6 USDHC: Use the ESDHC clock
mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
i.MX28: Add function to adjust memory parameters
mx28evk: Fix PSWITCH key position
mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
mx53ard: Remove unused CONFIG_MII_GASKET
mx6: Avoid writing to read-only bits in imximage.cfg
m28evk: use same notation to alloc the 128kB stack
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
commit acc4959fc1 (Revert "i.MX28: Enable additional DRAM address bits")
broke mx28evk boot.
Fix it by properly adjusting the HW_DRAM_CTL29 register value.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
If in case this is valid according to the latest datasheet, ignore this patch.
Acked-by: Marek Vasut <marex@denx.de>
|
|
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
There is no .S file in this directory, so just remove SOBJS.
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Original code was assuming that the fuse revision version for all mx53loco boards
based on Dialog PMIC was the same, which is not the case.
Force the revision of all Dialog-based boards to 0.
This fixes a kernel crash when PMIC is accessed in the 2.6.35 kernel
for Dialog rev E boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
fdt_set_phy_handle() makes several FDT calls that could fail, so it should
not be hiding these errors.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
|
On p1010rdb some signals are muxed for tdm/can/uart/flash.
If we don't set fsl_p1010mux:tdm_can to "can" or "tdm" explicitly,
defaultly we keep spi chip selection to spi-flash instead of to
tdm/slic and disable uart1 when not using flexcan, as well disable sdhc.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
|
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
is an integrated device that targets Femto base station market. It combines
Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
MAPLE-B2F baseband acceleration processing elements
BSC9131RDB Overview
-----------------
-1Gbyte DDR3 (on board DDR)
-128Mbyte 2K page size NAND Flash
-256 Kbit M24256 I2C EEPROM
-128 Mbit SPI Flash memory
-USB-ULPI
-eTSEC1: Connected to RGMII PHY
-eTSEC2: Connected to RGMII PHY
-DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Add USB device-tree fixup for following platforms:
MPC8536DS, P1022DS, P1023RDS, P2020COME, P2020DS, P2041RDB, P3060QDS
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
|
Add support for CLAA07LC0ACW LCD that connects to the mx53loco board.
Configure the board to show the Linux logo on the LCD.
Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account
the framebuffer usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
The ipuv3 driver is currently only used on mx51, but it can be extended to work
on mx53 and mx6 as well.
Rename mx51_fb_init(), so that it can be used by other SoCs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
