summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2019-02-19board/lx2160a: Add init_func_vid() definitionPriyanka Jain
Add init_func_vid() which calls adjust_vdd() This ensures adjust_vdd() is called via init_sequence_f[] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160: Add secure boot target and enable distro boot.Udit Agarwal
Adds esbc validate command for verification of MC and DPC firmware, along with secure boot defconfig. Also enable distro boot. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> [PK: squash "enable DM support for SATA patch" & add maintainer] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19lx2160: Enable support of EMC2305Meenakshi Aggarwal
Enable support for FAN controller EMC2305 for LX2160A RDB board. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> [PK: enable EMC2305 for lx2160rdb] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: emc2305: add support for fan controllerMeenakshi Aggarwal
Add support for fan controller emc2305. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19armv8: lx2160ardb : Add support for LX2160ARDB platformPriyanka Jain
LX2160ARDB is an evaluation board that supports LX2160A family SoCs. This patch add base support for this board. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> [PK: Sqaush patches from Yinbo Zhu, Peng Ma, Chuanhua Han and re-arrange defconfig] Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-15board: mx6sabresd: Remove the enet reset gpio handlingAbel Vesa
Rely on the phy-reset-gpios which is set in imx6qdl-sabresd dtsi and get rid of the enet reset gpio handling from the board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabresd: Remove non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabresd board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabreauto: Remove the non-DM codeAbel Vesa
Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabreauto board file. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabreauto: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabreauto. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15mx6sabresd: Add DM_GPIO supportAbel Vesa
Add the DM_GPIO related config for mx6sabresd. Also add the gpio request calls. Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-15board: mx6sabreauto: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabreauto - imx6qp-sabreauto - imx6dl-sabreauto Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15board: mx6sabresd: Add board_fit_config_name_match to support FIT in SPLAbel Vesa
This matches one of the following three boards (or fails): - imx6q-sabresd - imx6qp-sabresd - imx6dl-sabresd Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-05MAINTAINERS: Change fsl-qoriq, mpc85xx, mpc86xx maintainersYork Sun
Change maintainers to Prabhakar Kushwaha for fsl-qoriq, mpc85xx and mpc86xx. Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-28imx8mq_evk/README: remove ARCH environment variableBaruch Siach
There is no need to set the ARCH variable when building U-Boot. In fact, the ARCH name in U-Boot is 'arm'. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2019-01-28imx8qxp: mek: update READMEPeng Fan
Update README after we switch to use SPL Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28imx8qxp: mek: default enable SPLPeng Fan
Enable SPL for i.MX8QXP MEK, and currently use SPL FIT. The SPL enable SPL_DM to use MMC/PINCTRL/POWER DOMAIN/CLK. Note: SPL FIT could not support secure boot chain, because i.MX8/8X only support i.MX container format. This container format has not been upstreamed, so we use FIT for now. When SPL container supported, we could switch to that. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-17armv8: ls2088ardb: Update MAINTAINERSYork Sun
Signed-off-by: York Sun <york.sun@nxp.com> CC: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2019-01-17armv8: ls1088ardb: Update MAINTAINERSYork Sun
Signed-off-by: York Sun <york.sun@nxp.com> CC: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2019-01-17ls1046aqds: Bypass xfi port fixup for KR modeFlorinel Iordache
u-boot makes a fixup for LS1046AQDS board to setup the properties 'fixed-link' and 'phy-connection-type' to 'xgmii' but in case of backplane mode this fixup is not correct because it causes the KR link to fail and so it must be bypassed in order to keep the link in KR mode as it is defined in DTS. Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> [YS: Fix compiling warning] Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17fsl-layerscape: dpaa: fix fsl-mc status in fdt with bootefiMian Yousaf Kaukab
fsl-mc lazyapply command applies dpl from efi_exit_boot_services(). Status of fsl-mc node in working fdt is updated at this stage. However, an efi application like grub may already have copied the fdt. So the updates to fdt done at efi_exit_boot_services() may not be visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply command is used. Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot) Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls2088aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls2088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls2088ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls2088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - remove EL3 specific erratas for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1088aqds: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17armv8: ls1088ardb: Add TFABOOT supportPankit Garg
TFABOOT support includes: - ls1088ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - MC address changes for TFABOOT - define BOOTCOMMAND for TFABOOT - ifc chip select changes for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-01imx: add i.MX8MQ EVK supportPeng Fan
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to DRAM. The boot log with Arm trusted firmware console enabled: " U-Boot SPL 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) PMIC: PFUZE100 ID=0x10 Normal Boot Trying to boot from MMC2 NOTICE: Configureing TZASC380 NOTICE: BL31: v1.5(release):p9.0.0_1.0.0-beta-20180928-8-ge09c4b62-dirty NOTICE: BL31: Built : 09:28:54, Nov 8 2018 lpddr4 swffc start NOTICE: sip svc init U-Boot 2018.11-00142-g9ae14e7274 (Nov 20 2018 - 18:13:16 +0800) CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz Reset cause: POR Model: Freescale i.MX8MQ EVK DRAM: 3 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: Warning: ethernet@30be0000 using MAC address from ROM eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-01imx: imx8qxp_mek: imximage: remove config.hPeng Fan
config.h is not needed, remove it. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-12-10Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Add TFA boot flow for some Layerscape platforms Add support for lx2160a SoC [trini: Add a bunch of missing MAINTAINERS entries] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-06board/freescale/vid: Add vdd table for NXP LX2160A SoCPriyanka Jain
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06board/freescale/vid: Add correction for ltc3882 read error.Priyanka Jain
Voltage regulator LTC3882 device has 0.5% voltage read error. So for NXP SoC devices this generally equates to 2mV Update set_voltage_to_LTC for below: 1.Add coorection of upto 2mV in voltage comparison to take care of voltage read error of voltage regulator 2.Add loop max count kept as 100 to avoid infinte loop. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1088ardb_pb: Add support for board detectionPramod Kumar
ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc, board type detection is dynamic at boot time Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06arm: ls1021a: Add timer_init() in board_init_f for SPLAlison Wang
I2C is used to access DDR SPD in the DDR initialization for SPL. In i2c_write process, get_timer() will be called. In board_init_f for SPL, timer_init() is not called before. The system counter is not enabled and the counter frequency is not set to 12.5MHz in SPL. The parameters for do_div() are zero too. It could not be found until CONFIG_USE_PRIVATE_LIBGCC is enabled in default. When CONFIG_USE_PRIVATE_LIBGCC is enabled, U-Boot will use its own set of libgcc functions. As the parameters for do_div() are zero, __div0 will be called. Then the processor will stay in an endless loop after calling hang(). This patch will add timer_init() in board_init_f for SPL and fix a series of issues it caused. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012afrx: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be loaded by trusted firmware - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [YS: remove unnecessary braces] Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012aqds: fix secure boot compilationRajesh Bhagat
Includes environment.h file in ls1012aqds.c Also, enables pfe validation Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1012ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1012ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - enable PFE validation for secure boot Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1043aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1043aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1043ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1043ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN and QE address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1046aqds: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1046aqds_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06armv8: ls1046ardb: Add TFABOOT supportRajesh Bhagat
TFABOOT support includes: - ls1046ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - FMAN address changes for TFABOOT - define BOOTCOMMAND for TFABOOT Signed-off-by: York Sun <york.sun@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2018-11-27spi: Zap CONFIG_HARD_SPIJagan Teki
In legacy CONFIG_HARD_SPI initalizing spi_init code, which was removed during dm conversion cleanup. So remove the dead instances of CONFIG_HARD_SPI, and related code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-06mx8mq_evk: README: Delete file introduced by mistakeFabio Estevam
board/freescale/mx8mq_evk/README has been introduced by mistake in commit d0dd73974c61 ("imx: add i.MX8QXP MEK board support") Remove it for now as this should be introduced when mx8mq_evk support is in place. Reported-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2018-10-25Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imxTom Rini
Merged imx8 architecture, fix build for imx8 + warnings
2018-10-22imx: imx8qxp_mek: update to build image in U-BootPeng Fan
Update README Add imximage.cfg Update defconfig to include imximage.cfg Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-10-22imx: add i.MX8QXP MEK board supportPeng Fan
Add i.MX8QXP MEK board support Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver. Added README file. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-10-10driver: net: fsl-mc: Add support of multiple phys for dpmacPankaj Bansal
Till now we have had cases where we had one phy device per dpmac. Now, with the upcoming products (LX2160AQDS), we have cases, where there are sometimes two phy devices for one dpmac. One phy for TX lanes and one phy for RX lanes. to handle such cases, add the support for multiple phys in ethernet driver. The ethernet link is up if all the phy devices connected to one dpmac report link up. also the link capabilities are limited by the weakest phy device. i.e. say if there are two phys for one dpmac. one operates at 10G without autoneg and other operate at 1G with autoneg. Then the ethernet interface will operate at 1G without autoneg. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-09-29Merge tag 'mpc85xx-for-v2018.11-rc1' of git://git.denx.de/u-boot-mpc85xxTom Rini
Use device tree for mpc85xx with binman. Enabled for T2080QDS.
2018-09-27powerpc: dts: Enable device tree support for T2080QDSJagdish Gediya
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL so that device tree can be compiled. Update board README for device tree usage. Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add icid setup supportLaurentiu Tudor
Reuse the existing ICID setup code done for LS1046A smmu enablement and add the equivalent setup for LS1043A chips. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27ls1012afrwy: Add ls1012afrwy revC board support.Pramod Kumar
LS1012AFRWY supports three board revisions. Revision A and B board are collectively identified as revA/B, Revision C board is identifies as revC. Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> [York S: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-25 16:51:11 +0000