summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2013-09-27mx35pdk: Fix error handling in board_late_init()Fabio Estevam
If smc911x_initialize() fails we should return the error immediately. While at it, also check the error from cpu_eth_init(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-27mx28evk: Propagate the error if cpu_eth_init() failsFabio Estevam
If cpu_eth_init() fails we should return the error immediately. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx28evk: Fix checkpatch warningFabio Estevam
Fix the following checkpatch warning: $ ./tools/checkpatch.pl -F board/freescale/mx28evk/mx28evk.c CHECK: Alignment should match open parenthesis #109: FILE: freescale/mx28evk/mx28evk.c:109: + writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN, + &clkctrl_regs->hw_clkctrl_enet); Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6slevk: Add Ethernet supportFabio Estevam
mx6slevk has a SMSC8720 connected in RMII mode. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6qsabreauto: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Reset counter to prevent error messageFabio Estevam
If a HDMI cable is not connected, the following message is seen on boot: CPU: Freescale i.MX6Q rev1.1 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 No panel detected: default to HDMI unsupported panel HDMI Reset the 'i' variable to fix the 'unsupported panel' message. This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skip). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Avoid hang when HDMI cable is not connectedFabio Estevam
Since commit d9b894603 (mx6sabresd: Add LVDS splash screen support) the following hang happens if the HDMI cable is not connected or the 'panel' variable is not set: U-Boot 2013.10-rc2-12978-g47ac53d-dirty (Sep 11 2013 - 15:07:38) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 ... Provide a check to 'dev->detect' in order to prevent the hang. Reported-by: Pardeep Kumar Singla <b45784@freescale.com> Suggested-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-13Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
Conflicts: MAINTAINERS boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-09-10mx6sabresd: Add LVDS splash screen supportFabio Estevam
mx6sabresd boards can be connected to a Hannstar XGA LVDS panel. Add support for displaying U-boot splashscreen on it. By default, HDMI splash is selected. In order to use splash via LVDS, do the following in the U-boot prompt: setenv panel Hannstar-XGA save and reboot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-10ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut
Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-09-09SPL: P1022DS: switch to new multibus/multiadapter supportYing Zhang
- Added section "u_boot_list" in arch/powerpc/cpu/mpc85xx/u-boot-spl.lds - Use the function i2c_init_all instead of i2c_init Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-08-20powerpc/p1010rdb: fix calculating ddr_freq_mhzShengzhou Liu
There was a bug for calculating ddr_freq_mhz, it should be divided by 1000000 rather than 0x1000000. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/t4240: add QSGMII interface supportShaohui Xie
Also some fix for QSGMII. 1. fix QSGMII configure of Serdes2. 2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN. 3. fix dtb for QSGMII interface. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/t4240: fix lanes routing for QSGMII protocolsShaohui Xie
When using QSGMII protocols, the first lane and third lane on each slot need to be swapped. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/common/vsc3316: remove const from vsc3316_config parameter defineShaohui Xie
Since the parameters need to be modified according to different Serdes protocols at runtime, the const will block this. Also remove const from arrays define used by vsc3316_config. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20SPDX-License-Identifier: clean up license headerYork Sun
This patch cleans up license header in these files: board/freescale/p1022ds/spl.c drivers/mmc/fsl_esdhc_spl.c drivers/mtd/spi/fsl_espi_spl.c Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: Fix CamelCase checkpatch warningsPrabhakar Kushwaha
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions. because of this code checkpatch script generates "WARNING: Avoid CamelCase". Convert variables name to normal naming convention and modify board, driver files with updated the new structure. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: p1022ds: add TPL for p1022ds nand bootYing Zhang
TPL is introduced in the patch "NAND: TPL : introduce the TPL based on the SPL", here enable TPL for p1022ds nand boot. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc : p1022ds : Enable p1022ds to start from eSPI with SPLYing Zhang
Enable p1022ds to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPLYing Zhang
Enable p1022ds to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-18Merge branch 'master' of git://88.191.163.10/u-boot-armTom Rini
Fixup an easy conflict over adding the clk_get prototype and USB_OTG defines for am33xx having moved. Conflicts: arch/arm/include/asm/arch-am33xx/hardware.h Signed-off-by: Tom Rini <trini@ti.com>
2013-08-14powerpc/c29xpcie: add readme document for c29xpciePo Liu
Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-08-12powerpc/mpc85xx: Cleanup license header in source filesYork Sun
Fix the license header introduced by the following patches Add TWR-P10xx board support Add T4240EMU target IDT8T49N222A configuration code Add C29x SoC support Add support for C29XPCIE board Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/c29xpcie: add support for C29XPCIE boardMingkai Hu
C29XPCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. It includes C293PCIE board, C293PCIE board and C291PCIE board. - 512KB platform SRAM in addition to 512K L2 Cache/SRAM - 512MB soldered DDR3 32bit memory - CPLD System Logic - 64MB x16 NOR flash and 4GB x8 NAND flash - 16MB SPI flash Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Singed-off-by: Po Liu <Po.Liu@freescale.com> [yorksun: Fixup include/configs/C29XPCIE.h] Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09board/b4860qds: Add support for configuring SerDes1 RefclksShaveta Leekha
1) Add support in B4860 board files for using IDT driver where IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer that generate different refclks for SerDes modules, used this driver for reconfiguring SerDes1 Refclks(based on SerDes1 protocols) for CPRI to work. CPRI works on 122.88MHz and default refclks coming on board are not suitable for it 2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file to b4860qds board file, as SerDes1 Refclk1 would come from PHY MUX in case of certain protocols, that have been checked here. This change would make on board SGMIIs to work 3) Add I2C addresses for IDT8T49N222A devices in board/include file 4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-09board/freescale/common: IDT8T49N222A configuration codeShaveta Leekha
Add code for configuring IDT8T49N222A device for various output refclks - The IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer with alarm and monitoring functions suitable for networking and communications applications. It is able to generate wide range of output frequencies. - In B4860QDS, it has been used to generate different refclks to SerDes modules - Programming of these devices are performed by I2C interface. Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-09board/bsc9132qds: Configure DSP DDR controllerPriyanka Jain
BSC9132 SoC has two separate DDR controllers for PowerPC side and DSP side DDR. They are mapped to PowerPC and DSP CCSR space respectively. BSC9132QDS has two on-board MC34716EP DDR3 memory one connected to PowerPC and other to DSP side controller. Configure DSP DDR controller similar to PowerPC side DDR controller as memories are exactly similar. Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-09board/bsc9132qds: Add DSP side tlb and lawsPriyanka Jain
BSC9132QDS is a Freescale Reference Design Board for BSC9132 SoC which is a integrated device that contains two powerpc e500v2 cores and two DSP starcores. To support DSP starcore -Creating LAW and TLB for DSP-CCSR space. -Creating LAW for DSP-core subsystem M2 and M3 memory -Creating LAW for 1GB DDR which is connected exclusively to DSP-cores Signed-off-by: Manish Jaggi <manish.jaggi@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-09p1020rdb-pd: platform supportHaijun.Zhang
Add new board p1020RDB-PD. P1020RDB-PD board was update from P1020RDB. DDR changed from DDR2 1G to DDR3 2G. NAND: 128 MiB Flash: 64 MiB Also change P1020RDB to P1020RDB-PC to distinguish from P1020RDB board. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com> CC: Scott Wood <scottwood@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/mpc8xxx: Add memory reset controlYork Sun
JEDEC spec requires the clocks to be stable before deasserting reset signal for RDIMMs. Clocks start when any chip select is enabled and clock control register is set. This patch also adds the interface to toggle memory reset signal if needed by the boards. Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/t4240qds: Adjust DDR timing for RDIMMYork Sun
RDIMM has different timing. Tested RDIMM is MT18JSF1G72PDZ-1G9E1 for dual rank. Single- and quad-rank are not tested due to availability. Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/T4240EMU: Add T4240EMU targetYork Sun
Add emulator support for T4240. Emulator has limited peripherals and interfaces. Difference between emulator and T4240QDS includes: ECC for DDR is disabled due the procedure to load images No board FPGA (QIXIS) NOR flash has 32-bit port for higher loading speed IFC and I2C timing don't really matter, so set them fast No ethernet Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/corenet: Move RCW print to cpu.cYork Sun
The RCW print is common for all corenet platforms. Not necessary to ducplicate in each board file. Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/85xx: Add TWR-P10xx board supportXie Xiaobo
TWR-P1025 Specification: ----------------------- Memory subsystem: 512MB DDR3 (on board DDR) 64Mbyte 16bit NOR flash One microSD Card slot Ethernet: eTSEC1: Connected to Atheros AR8035 GETH PHY eTSEC3: Connected to Atheros AR8035 GETH PHY UART: Two UARTs are routed to the FDTI dual USB to RS232 convertor USB: Two USB2.0 Type A ports I2C: AT24C01B 1K Board EEPROM (8 bit address) QUICC Engine: Connected to DP83849i PHY supply two 10/100M ethernet ports QE UART for RS485 or RS232 PCIE: One mini-PCIE slot Signed-off-by: Michael Johnston <michael.johnston@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> [yorksun: Fixup include/configs/p1_twr.h] Signed-off-by: York Sun <yorksun@freescale.com>
2013-07-31Merge git://git.denx.de/u-boot-armStefano Babic
Conflicts: board/freescale/mx6qsabrelite/Makefile board/freescale/mx6qsabrelite/mx6qsabrelite.c include/configs/mx6qsabrelite.h Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-07-27mx6qsabresd: Add splash screen support via HDMIPardeep Kumar Singla
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
2013-07-26mx6qsabrelite: Remove mx6qsabrelite code in favor of nitrogen6xFabio Estevam
mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the code duplication and only use the nitrogen6x source code to make board code maintainance easier. Tested booting a mainline device tree kernel on a mx6qsabrelite board. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-07-24Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
2013-07-23vf610: Add I2C support for Vybrid VF610 platformAlison Wang
This patch adds I2C support for Vybrid VF610 platform and adds I2C0 support to VF610TWR board. Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23i2c, fsl_i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23i2c, soft-i2c: switch to new multibus/multiadapter supportHeiko Schocher
- added to soft_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-15PPC MPC83xx: Fix MPC8323ERDB build warningWolfgang Denk
Fix: mpc8323erdb.c: In function 'mac_read_from_eeprom': mpc8323erdb.c:198:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] Signed-off-by: Wolfgang Denk <wd@denx.de> cc: Timur Tabi <timur@tabi.org> cc: Kim Phillips <kim.phillips@freescale.com>
2013-07-12Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and serial. Conflicts: arch/arm/dts/exynos5250.dtsi Signed-off-by: Tom Rini <trini@ti.com>
2013-06-28Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-06-26mx28evk: Move README file inside board directoryFabio Estevam
Board specific READMEs should be located inside the respective board directory. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26imx: Add support for the SabreSD shipped with i.MX6DLPierre Aubert
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the support of the i.MX6DL. The config file and the board directory are renamed to remove the reference to the MX6Q. Signed-off-by: Pierre Aubert <p.aubert@staubli.com> CC: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-22Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-06-21arm: make __rel_dyn_{start, end} compiler-generatedAlbert ARIBAUD
This change is only done where needed: some linker scripts may contain relocation symbols yet remain unchanged. __rel_dyn_start and __rel_dyn_end each requires its own output section; putting them in relocation sections changes their flags and breaks relocation. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
generated by cgit (git 2.34.1) at 2024-12-27 13:41:28 +0000