| Age | Commit message (Collapse) | Author |
|---|
|
This setup is a bit special as Linux kernel (4.19) is not supporting
in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA)
operation.
For that reason it was necessary to provide a bootarg to allow userspace
enable it afterwards if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
As EHCI on i.MX5 has been converted to driver model, the board specific
code, necessary for VBUS USB power supply setup is not needed anymore.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
After switching to DM/DTS support of esdhc3 - the code in this patch
can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
After commit efd0b791069a ("eth: dm: fec: Add gpio phy reset binding")
the in-board file definition of ETH PHY reset can be removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The serverip part is provided from DHCP server with
'option root-path "192.168.3.1:/srv/tftp/rootfs";' parameter in dhcpd.conf
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The quotes around ${bootargs} were missing as we elaborate those variables
twice - once when we "setenv" the command and secondly when we "run" it.
Without quotes we have just empty string in the second call.
Moreover there is an issue with line breaks - as the original commands
got truncated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The 'dhcp' command is more versatile as it allows working with the DHCP
server to obtain serverip, ipaddress and other network parameters.
The configuration necessary to obtain the serverip (dhcpd.conf):
option option-150 code 150 = ip-address;
and in the subnet definition:
option option-150 192.168.X.Y;
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The 'rootpath' can be provided by DHCP server. Removing this line prevents
from overwriting it.
To do that on the DHCP server side (isc-dhcp-server) modify dhcpd.conf
and add 'option root-path "192.168.X.Y:/srv/tftp/rootfs";'
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The get_board_rev() is not needed anymore as a generic function
for the imx53 SoC has been used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This code provides information if the K+P's imx53 boards had KEY1
pressed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This change gives the opportunity to adjust Linux command line for the
imx53 device with some legacy data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This commit adds support for DDC and HSC boards from
K+P in u-boot.
Console output:
U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: WDOG
Model: K+P iMX53
DRAM: 512 MiB
MMC: FSL_SDHC: 0
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Module EEPROM:
ID: TQMa53-CB.0401
SN: 63152762
MAC: 00:0b:64:03:14:2a
BBoard:40x0 Rev:10
Net: eth0: ethernet@63fec000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
By using this file one can avoid cluttering <board>.h file with u-boot
HUSH commands necessary for booting target device.
With such approach the commands are stored only in one place and can be
reused if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
This commit provides support for Kieback & Peter GmbH IMX6Q based
TPC board.
U-boot console output:
U-Boot SPL 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)
Trying to boot from MMC1
U-Boot 2018.05-rc1-00005-g631e2d01fd (Apr 04 2018 - 21:16:24 +0200)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 37C
Reset cause: POR
Board: K+P KP_IMX6Q_TPC i.MX6Q
Watchdog enabled
I2C: ready
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Autoboot in 3 seconds
|
