| Age | Commit message (Collapse) | Author |
|---|
|
This commit adjusts the autoboot.cmd file to use ${mmcbootdev} instead of
hardcoded value 0.
This is necessary to allow booting this board from the SD card.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
After the commit 9b643e312d52 ("treewide: replace with error() with
pr_err()"), there are some pr_err() with no line break. Add missing
line breaks.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Exynos5422 board has s2mps11 pmic.
If CONFIG_PMIC_S2MPS11 is enabled, it can initialize PMIC and Regulators
during booting time.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no build-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for build-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
This patch also updates Odroid's ADCmax array and reduces ADC tolerance
to 1% to ensure that XU4 and HC1 revisions are properly detected.
I've tested this with XU3, XU3-lite, XU4 and HC1 boards. In case of my test
boards I got following values from ADC register: 372, 370, 1281 and 1313.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We should not be including a PMIC header file in the board config. Move it
to a C file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is not used by any board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Clean up board_f sequence a little
This series tries to remove #ifdefs from the board_f init sequence. It
gets as far as I2C and then we need to discuss whether we can start to
remove the old I2C framework.
I think that ideally each entry in the init sequence should be enabled by
at most one CONFIG, which is in Kconfig and is not arch-specific.
END
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
We don't ever search for these so there is no need for a 4KB alignment.
It just wastes space.
Drop this and use the standard 4-byte alignment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
For snow when chainloading u-boot the CPU seems to be running at full
speed. The lower CPU voltage seems to be ok for u-boot, but when booting
linux (bringing up all cores) I'm seeing random crashes.
Bump the voltage up to a level that's safe for all cpu frequencies.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This function controls enabling the EDP PHY. Rename it and drop the existing
weak functions, which are confusing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This file currently requires LCD support. Adjust it so that it can still be
built without LCD support (even thought it won't work fully).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch will fix these checkpatch issues.
CHECK: Alignment should match open parenthesis
+ printf("Enter: %s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\n\n\t%s %s\n", mode_name[mode][0],
+ mode_info[mode]);
CHECK: Alignment should match open parenthesis
+ lcd_printf("\t%s %s - %s\n\n", selection[i],
+ mode_name[i][0],
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.
The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision
There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
Rev ADC Board
0.1 0 XU3 0.1
0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT
0.3 1280 XU4 0.1
The detection code depends on the ADC+10% value.
Implementation of functions:
- set_board_type() - read ADC and set type
- get_board_rev() - returns board revision: 1..3
- get_board_type() - returns board type string
Additional functions with return values of bool:
- board_is_generic() - true if found compatible "samsung,exynos5"
but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
and XU4 revision.
After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().
Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
The function get_board_type() is called in two places by common code,
but the returned pointer was never check.
This commit adds checking the returned pointer, before use it.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
If board uses downstream Chrome OS U-Boot as first stage
bootloader and upstream version is chained second stage,
1.1V is minimum voltage borderline.
Signed-off-by: Misha Komarovskiy <zombah@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Since device tree is used for all exynos5 boards, we can remove the #ifdef
and reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some boards use device tree for almost all board-specific configuration.
They therefore do not need their own separate board code, but can all use
the same version. Add a common version of the board code. It uses the
PMIC, regulator and video bridge uclasses. This will support smdk5250,
smdk5420, snow, spring, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
|
|
This fix is necessary to avoid booting the default ITB configuration.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
This commit adds example scripts of boot.scr:
- bootzimg.cmd - check if dtb exists and boot zImage
- autoboot.cmd - check which image exists: Image.itb, zImage or uImage
and optionally load fdt file for u/zImage
The blank spaces are added to improve readability and can be removed
before use mkimage.
Required U-Boot environment variables: $boardname, $fdtfile, $console,
$mmcbootdev, $mmcbootpart, $mmcrootdev, $mmcrootpart, $rootfstype.
Making boot.scr from file.cmd:
mkimage -C none -A arm -T script -d file.cmd boot.scr
The Odroid XU3 default environment is ready for those boot scripts and
the right script can be loaded by DFU.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
|
This commit adds implementation of function calls:
- usb_gadget_handle_interrupts()
- board_usb_init()
Which allow enable USB DWC3 gadget for this board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
|
This change enables the configs required to init and setup max77686
regulator driver, using the new driver model pmic and regulator API.
And also changes the old pmic framework calls to the new ones.
This commits enables:
- CONFIG_ERRNO_STR
- CONFIG_DM_PMIC
- CONFIG_DM_PMIC_CMD
- CONFIG_DM_PMIC_MAX77686
- CONFIG_DM_REGULATOR
- CONFIG_DM_REGULATOR_CMD
- CONFIG_DM_REGULATOR_MAX77686
And removes the unused:
- CONFIG_DM_I2C_COMPAT
- CONFIG_POWER
- CONFIG_POWER_I2C
- CONFIG_POWER_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
In the power_init_board function call, regulator driver init is called,
so before compile, make sure that any power framework is defined.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Since driver model will probe the EC when it is first used, we do not
need to init it explicitly.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This definition is necessary for Exynos based boards to work properly.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Since more than one board requires memory reservation
for the secure firmware, the reservation code can be
made in a common code.
Now, to reserve some part of the the last bank,
board config should define:
- CONFIG_TZSW_RESERVED_DRAM - len in bytes
- CONFIG_NR_DRAM_BANKS - number of memory banks
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Hyungwon Hwang <human.hwang@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
4.8 warning
This patch suppress following warning:
board/samsung/common/board.c:95:32: warning: iteration 4u invokes undefined behavior [-Waggressive-loop-optimizations]
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
^
board/samsung/common/board.c:94:2: note: containing loop
about possible signed integer overflow at gcc 4.8.2 (odroid board)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This common call can be used for setting proper entities based
on dfu command arguments.
The config: CONFIG_SET_DFU_ALT_INFO, was used only for few configs,
and now it is common.
The board file should implement:
- set_dfu_alt_info() function
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[Test HW: Odroid U3 (Exynos 4412)]
|
|
Some exynos boards require special handling of nRESET_OUT line for eMMC
memory to perform complete reboot e.g. Odroid X2/U3/XU3 boards.
This will support eMMC reset using DT from reset_misc of samsung common
board file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
|
|
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Previously, we used to statically assign values for vl_col, vl_row and
vl_bpix using #defines like LCD_XRES, LCD_YRES and LCD_COLOR16.
Introducing the function exynos_lcd_early_init() would take care of this
assignment on the fly by parsing FIMD DT properties, thereby allowing us
to remove LCD_XRES and LCD_YRES from the main config file.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
