| Age | Commit message (Collapse) | Author |
|---|
|
Last user of this option went away in commit:
fdc7718999 ("board: usb_a9263: Update to support DT and DM")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT, don't delete gurnard DTB creation]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Due to introducing the new UTMI PLL clock handle functions,
use the functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Due to introducing the new peripheral clock handle functions,
use these functions to reduce duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[Rebased on current master, fixup for at91rm9200ek]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
add support for DFU on the corvus board.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
- rename at91_spl_board_init into spl_board_init
- use SZ_1X defines for sizes
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
On these boards the DDR is connected to a dedicated controller and not
to chip select 1 of the EBI.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Tested-by: Erik van Luijk <evanluijk@interact.nl>
|
|
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
- corvus board fix problems with toshiba nand chips
on the corvus board problems with toshiba chips
Manufacturer ID: 0x98 Chip ID: 0xdc encounterd.
Solve this in the following way:
- set other nand timings
- enable CONFIG_SYS_NAND_READY_PIN
- correct the MACH_TYPE setting
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
