summaryrefslogtreecommitdiff
path: root/board/sunxi
AgeCommit message (Collapse)Author
2015-04-15sunxi: Yones Toptech BD1078 supportPaul Kocialkowski
The Yones Toptech BD1078 is an A20 based 10" tablet with a 1024x600 lcd screen, volume up/down and back buttons, headphones jack, mini hdmi, micro usb (otg), micro usb (host), external micro-sd slot and a separate internal micro-sd slot. Also see: http://linux-sunxi.org/Yones_Toptech_BD1078 Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: Complete mmc pin mux for each supported platform, configured with KconfigPaul Kocialkowski
Sunxi platforms have different possible mmc pin mux setups (except for mmc0), which are different across platforms. This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig options. This is especially relevant when a second (in addition to mmc0) port is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: GPIO pin mux hardware-feature-specific function index definesPaul Kocialkowski
Each hardware feature exposed through the GPIO pin mux is usually using the same function index (for a given port), so there is no need to define one value per pin: one value per hardware feature per port is sufficient, avoids duplication and makes everything easier to understand. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: Ainol AW1 supportPaul Kocialkowski
The Ainol AW1 is an A20 based tablet with a 800x480 lcd screen, sdio wifi, volume up/down and home buttons, micro-sd slot, micro usb (otg), headphones connector and a SPCI modem connector. Also see: http://linux-sunxi.org/Ainol_AW1 Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: USB download gadget cable detectionPaul Kocialkowski
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sunxi: common VBUS detection logic in usbcPaul Kocialkowski
VBUS detection could be needed not only by the musb code (to prevent host mode), but also by e.g. gadget drivers to start only when a cable is connected. In addition, this allows more flexibility in vbus detection, as it could easily be extended to other USBC indexes. Eventually, this would help making musb support independent from a hardcoded USB controller index (0). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15sun6i: Add support for the Mixtile LOFT-Q boardHan Pengfei
The Mixtile LOFT-Q is an A31 based board with 2G RAM, 8G EMMC, sdio wifi, 1Gbit ethernet, HDMI display, toslink audio plug, 4 USB2.0 port, external USB2SATA connector, sd card plug, 3x60 external fpic expansion connector, NXP JN5168 zigbee gw, remote support. Also see http://focalcrest.com/en/pc.html#pro02 Signed-off-by: Han Pengfei <pengphei@sina.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29sunxi: UTOO_P66: Add missing MAINTAINERS entryHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29sunxi: use CONFIG_SYS_CLK_FREQ to set cpu clockIain Paton
make the CPU clock selectable via Kconfig this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each soc header and replaces it's use in board/sunxi/board.c with CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board specific frequency on boot Signed-off-by: Iain Paton <ipaton0@gmail.com> [hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the arch-timer clk speed on sun7i to fix mis-compile on sun7i] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: video: Fix VIDEO_LCD_PANEL_I2C being enabled by defaultHans de Goede
Fix a typo in board/sunxi/Kconfig which caused VIDEO_LCD_PANEL_I2C to be enabled on all sunxi boards. Also fix a compile error which shows up once VIDEO_LCD_PANEL_I2C is actually disabled on most boards as it should be. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sunxi: Add Wexler TAB7200 supportAleksei Mamlin
This patch add support for Wexler TAB7200 tablet. The Wexler TAB7200 is a A20 based tablet with 7 inch display(800x480), capacitive touchscreen(5 fingers), 1G RAM, 4G NAND, micro SD card slot, mini HDMI port, 3.5mm audio plug, 1 USB OTG port and 1 USB 2.0 port. Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sun7i: Add support for the Orange Pi Mini boardHans de Goede
The Orange Pi Mini is an A20 based development board featuring 1G RAM, HDMI, 1Gbit ethernet, USB wifi, SATA, 2 sdcard slots (use the top one for booting), 2 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V. Also see: http://www.orangepi.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun7i: Add support for the Orange Pi boardHans de Goede
The Orange Pi is an A20 based development board featuring 1G RAM, HDMI & VGA, 1Gbit ethernet, USB wifi, SATA, 4 USB 2.0 A receptacles, a micro USB B receptacle (otg) and a 3 ring 3.5 mm jack connector for A/V. Also see: http://www.orangepi.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun7i: Add support for the Wits Pro A20 DKT boardHans de Goede
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND, sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen and a ton of IO connectors. Note there seem to be multiple sdcard slots on the board (4 in total), but other then mmc0 none of these are hooked up by default, there is a ton of dip-switches which likely allow hooking some of these up, but the documentation of the board only describes the use of a fraction of them, so for now we only support mmc0. Also see: http://www.merrii.com/en/pla_d.asp?id=163 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sunxi: Add support for the Forfun Q88DB tabletJens Lucius
The Forfun Q88DB is an A13 tablet in the common Q8 format. Features are 512MB RAM, 4GB NAND, 7" Display, RTL8188 Wifi, 2 cameras. For more details see: http://linux-sunxi.org/Forfun_Q88DB Signed-off-by: Jens Lucius <info@jenslucius.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-10sun6i: Add support for the Mele I7 boardMarcus Cooper
The Mele I7 is a Allwinner based Android TV box. It features a A31 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out, SPDIF, IrDA, 3 USB A, 1 USB micro OTG and Wireless LAN. Signed-off-by: Marcus Cooper <codekipper@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sun7i: Add support for the MK808C boardMarcus Cooper
The MK808C is a Allwinner based Android TV dongle. It features a A20 SOC, 1G RAM, 8GB NAND, HDMI out, A/V out, 1 USB A, 1 USB mini OTG, Bluetooth and Wireless LAN. Signed-off-by: Marcus Cooper <codekipper@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: Add support for the Jesurun Q5 boardGábor Nyers
The Jesurun Q5 has a black plastic casing with the approximate dimensions of 100mm x 100mm x 24mm with rounded edges. In terms of hardware it features an Allwinner A10 SoC with 1GB RAM and 8GB of NAND flash. The storage capacity can be extended up to 32GB with a MicroSD card. The external connectors are: 2x USB-A female supporting USB2.0, 3.5mm female jack for audio, HDMI female, SPDIF, RJ45 LAN and Power. In addition the device has 1x red LED (hard wired to power) and an programmable green led. On the board there is also an unpopulated IR receiver and the UART. The devices is equipped with an AXP209 PMU. For more details see: http://linux-sunxi.org/Jesurun_Q5 Signed-off-by: Gábor Nyers <gnyers@opensuse.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-10sunxi: Make CONFIG_DRAM_TPR3 apply to sun[57]iAdam Sampson
The tpr3 (timing skew) parameter is used in all supported versions of the sunxi DRAM controller, but it was only enabled for sun4i in 47e3501a76894f4ba08bc61f33774bd5d39ff464. Signed-off-by: Adam Sampson <ats@offog.org> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-21sunxi: musb: Check Vbus-det before enabling otg port powerHans de Goede
Sending out 5V when there is a charger connected to the otg port is not a good idea, so check for this and error out. Note this commit currently breaks otg support on the q8h tablets, as we need to do some magic with the pmic there to get vbus info, this is deliberate (better safe then sorry), fixing this is on my TODO list. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20sunxi: video: Add support for tl059wv5c0 lcd panelsHans de Goede
Add support for the 6" 480x800 tl059wv5c0 panel used on e.g. Utoo P66 and Aigo M60/M608/M606 tablets. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20sunxi: video: Add support for LCD panels which need to be configured via i2cHans de Goede
This commits adds support for configuring a a bitbang i2c controller, which is used on some boards to configure the LCD panel (via i2c). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-20sunxi: video: Add support for LCD reset pinHans de Goede
On some boards there is a gpio to reset the LCD panel, add support for this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-16sunxi: Normalise FEL supportSimon Glass
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of creating its own. There are some #ifdefs required in start.S. Future work will hopefully remove these. This series is available at u-boot-dm, branch sunxi-working. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16sunxi: MAINTAINERS: drop no longer existing felconfig-s from MAINTAINERSHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16sunxi: Ampe A76 supportPaul Kocialkowski
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: dram: Support more sun[457]i dram parameters in KconfigSiarhei Siamashka
This patch allows to configure all the important DRAM parameters in Kconfig. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: dram: Optionally use standard JEDEC timings for sun[457]iSiarhei Siamashka
In addition to the current Android magic settings, allow to optionally use DDR3 timing parameters, which are tailored for different clock frequencies and JEDEC speed bins. This should improve reliability and performance. Adding '+S:CONFIG_DRAM_TIMINGS_DDR3_1066F_1333H=y' to the board defconfig allows to use timings, which are calculated for the DDR3-1066F speed bin. A lot of DDR3 chips, which are used in real Allwinner based devices, support DDR3-1066F speed bin timings. And adding '+S:CONFIG_DRAM_TIMINGS_DDR3_800E_1066G_1333J=y' should work with any DDR3 chips, because this targets the slowest JEDEC speed bins. The vendor magic values are still used by default for DRAM, but board maintainers now have more flexibility in DRAM timings selection. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: video: Force h/vsync active high when using ext. vga dac on some boardsHans de Goede
On both my A13-OLinuxIno and my A13-OLinuxIno-Micro, the vga output gives an unstable image when active low v or hsync is used. The problem seems to be specific to the OLinuxIno A13 (normal & micro) boards. I've just looked up the schematics and they use an opendrain driver for the vga sync lines, and with sync pulses it is the logical high->low edge of the pulse which counts for the timing, which with an active low sync is being driven by the pull-up, and that simply seems to not drive it hard enough to get a stable image. So force v and hsync active high on these boards. independent of what the modeline says. This fixes the unstable image. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02sunxi: Add Inet 86VS supportMichal Suchanek
Signed-off-by: Michal Suchanek <hramrach@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: TZX-Q8-713B7 supportPaul Kocialkowski
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: Add Linksprite_pcDuino3_Nano board / defconfigAdam Sampson
This is a low-cost Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and another for power in, HDMI, SATA, 5V power for SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector. Like the BananaPi, this board needs GMAC_TX_DELAY set to 3 in order for GMAC to work reliably at gigabit speeds. For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano Signed-off-by: Adam Sampson <ats@offog.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: MAINTAINERS: sort entries alphabeticallyHans de Goede
Keep all entries except for the monster entry at the top alphabetically sorted. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02sunxi: Remove CONFIG_TARGET_FOO for sun5i and sun7i boardsHans de Goede
CONFIG_TARGET_FOO was only used in board/sunxi/Makefile to select the dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some special handling of the bananapi/bananapro (both sun7i), all sun5i and sun7i boards have been moved over to using a single dram_sun5i_autoconfig file, and the tx clk delay handling for the Banana boards now has its own Kconfig. IOW nothing is using CONFIG_TARGET_FOO anymore, so remove it. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02sunxi: Add a GMAC Transmit Clock Delay Chain Kconfig optionHans de Goede
And use this to set the GMAC Transmit Clock Delay Chain value on Banana boards, rather then keying of CONFIG_TARGET_FOO. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02sunxi: Convert sun5i boards to use auto dram configurationHans de Goede
Currently we've separate detailed dram settings for all sun5i boards, this moves them over to using auto dram configuration so that we can get rid of all the per board dram_foo.c files. This has been tested on a A10s-Olinuxino, A13-Olinuxino, A13-OlinuxinoM, mk802-a10s and r7-tv-dongle board. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: Add Hyundai A7HD supportHans de Goede
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD Cc: Mark Janssen <maniac@maniac.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: video: Make pwm polarity configurableHans de Goede
It turns out that there are some panels where the pwm input is not active low, so make it configurable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: Add support for Mele M5.Ian Campbell
HDMI, SATA, USB and Ethernet appear functional, I've not done extensive tests of all peripherals though. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-23sunxi: Convert sun7i boards to use auto dram configurationHans de Goede
Currently we've separate detailed dram settings for all sun7i boards, this moves them over to using auto dram configuration so that we can get rid of all the per board dram_foo.c files. This has been tested on a A20-Olinuxino-Lime, A20-Olinuxino_MICRO, Bananapi, Bananapro, Cubieboard2, Cubietruck, Mele_M3 and a Linksprite_pcDuino3. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: Drop qt840a_defconfigHans de Goede
The qt840a is one of the many tv-boxes using the "i12" A20 pcb, but it populates only one of the 2 places for a 16 bit dram ic, thus reducing the buswidth to 16 bits, and the amount of ram to 512M, which is why we had a separate config for it. This commit switches the generic i12-tvbox_defconfig over to DRAM autoconfiguration, so that it will work with the qt840a too, and drops the qt840a specific config, like we've done with other memory-amount specific configs before. Tested on a generic i12-tvbox with 32 bit bus-width / 1G RAM, and on a qt840a with 16 bit bus-width / 512M RAM. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: Add new Chuwi V7 CW0825 board / defconfigHans de Goede
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash, microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out, stereo speakers, front & back camera and usb wifi. It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the tablet. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-23sunxi: video: Add support for Hitachi tx18d42vm LVDS LCD panelsHans de Goede
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a lcd controller which needs to be initialized over SPI, once that is done they work like a regular LVDS panel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22sunxi: Hookup OTG USB controller supportHans de Goede
Hookup OTG USB controller support and enable the otg controller + USB-keyb on various tablets. This allows tablet owners to interact with u-boot without needing to solder a serial console onto their tablet PCB. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22sunxi: Add Gemei G9 (Allwinner A10/sun4i) tabletPriit Laes
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768 IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250 accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot, miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and 3.5mm headphone jack. More details are available at: http://linux-sunxi.org/Gemei_G9 Signed-off-by: Priit Laes <plaes@plaes.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22sunxi: Add Marsboard A10 supportAleksei Mamlin
This patch add support for Marsboard A10 board. The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND, micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port, 1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic, it does not have a pmic at all. Board also have 2 expansion 70 pin headers. Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22video: sunxi: Hook up SSD2828 with the sunxi video driverSiarhei Siamashka
Convert GPIO names from Kconfig strings into pin numbers for the 'ssd2828_config' struct. Add SSD2828 initialization between enabling the parallel LCD interface and turning on the backlight. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22sunxi: axp221: Add ELDO[1-3] supportSiarhei Siamashka
And also add Kconfig option for selecting ELDO3 voltage. The reason for having this option is that the Android kernel sets ELDO3 to 1.2V when powering up LCD in the case if 'lcd_if' configuration variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely to supply power for a SSD2828 chip. However on the MSI Primo81 tablet, which is using this particular 'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to be unnecessary and it works regardless. Having no schematics of this tablet, I can only guess that 1.2V is supplied to SSD2828 in some other way. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-22sunxi: Add mk802_a10s board / defconfigHans de Goede
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG) and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic, the axp152. For more details see: http://linux-sunxi.org/Semitime_g2 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22sunxi: Add mk802ii board / defconfigHans de Goede
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic. For more details see: http://linux-sunxi.org/Rikomagic_mk802ii Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
generated by cgit (git 2.34.1) at 2024-12-26 06:26:35 +0000