| Age | Commit message (Collapse) | Author |
|---|
|
Add initial defconfig support for AM65x that runs on A53.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial DT support for AM654 EVM that runs on A53.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
|
|
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly
to all the other DRA7 and AM5 SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI CEC pins are set to pull-up, but CEC requires no pull. Fix this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
A common voltage of 1.35V was being programmed for all am43 board
versions. EPOS-EVM Needs 1.20V for LPDDR2.
Fixes: fc69d472621b5 (“board: ti: AM43XX: Add ddr voltage rail configuration”)
Reported-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
If CONFIG_SPL_SERIAL_SUPPORT is not set, then the build will fail:
board/ti/am335x/built-in.o: In function `spl_start_uboot':
board/ti/am335x/board.c:247: undefined reference to `serial_tstc'
board/ti/am335x/board.c:247: undefined reference to `serial_getc'
Avoid the calls to the serial functions in that case.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
When compiling without CONFIG_CLOCK_SYNTHESIZER (which is implied by
CONFIG_DRIVER_TI_CPSW for am335x_evm), exclude the network setup for
AM335x-ICEv2 to avoid link time failures:
board/ti/am335x/board.c:683: undefined reference to `setup_clock_synthesizer'
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
U-boot
AM437x QSPI boot is a single stage boot and hence needs runtime DTB
selection to support AM437x-SK and AM437x-IDK with DM enabled. This is
required to move am43xx_evm_qspiboot_defconfig to use DM/DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.
https://beagleboard.org/pocket
This was tested using the am335x_evm_usbspl_defconfig.
Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
U-boot CONFIG
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965e4 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
functions
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add pinmux for QSPI pins on K2G ICE board.
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 BeagleBoard(s).
|
|
Add initial dts support for am574x-idk
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
|
|
Update prcm, voltages and pinmux support for am574x-idk.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
am574x-idk is a board based on TI's am574 processor
Add eeprom support.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.
Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:
/*
* Reset any devices that may be in a bad state when applying
* the power. This is a __weak function. Resetting of the devices
* should occur in the board file of the device.
*/
for (i = 0; i < dev->maxchild; i++)
usb_hub_reset_devices(i + 1);
This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.
Existing implementations are changed to accept and ignore the new
parameter.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
|
|
We don't want this build anymore.
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This comment creates a wrong entry in config_whitelist.txt.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
