| Age | Commit message (Collapse) | Author |
|---|
|
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The same change as was done for zynqmp with this description:
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0= &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
<zynqmp example removed>
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add missing header detected by sparse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
|
|
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This commit moves the FPGA descriptor definition
to mach-zynq, where it makes more sense.
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56fab ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When static memory configuration is used U-Boot has capability to detect
memory size in setup range. Enable this feature for static
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Fix my fragments to list all files in the repo.
Also fix path to for Xilinx Zynq SoC (mach-zynq)
It should be the part of
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)
And cover dts files in board MAINTAINERS files.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Updating year in zynq files. Also add missing Copyright to board.c.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Simplify ps7_init* initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Simplify ps7_init* initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Simplify ps7_init* initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Simplify ps7_init* initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
After some generic cleanup adding ps7_init* to repository
is not big pain now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Show information about silicon in bootlog.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use generic implementation. It will also reduce config data size for
converted boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
SPL is not calling this code that's why it is dead code and can be
removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There is no reason not to return return value from above function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
modeboot variable is used for saving inforation which bootmode
is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The dram_init and dram_init_banksize functions were using a board
specific implementation for decoding the memory banks from the fdt. This
board specific implementation uses a static variable 'tmp' which makes
these functions unsafe for execution from within the board_init_f
context.
This unsafe use of a static variable was causing a specific bug when
using the zynq_zybo configuration, U-Boot would generate the following
error during image load. This was caused due to dram_init overwriting
the relocations for the 'image' variable within the do_bootm function.
Out of coincidence the un-initialized memory has a compression type
which is the same as the value for the relocation type R_ARM_RELATIVE.
Uncompressing Invalid Image ... Unimplemented compression type 23
It should be noted that this is just one way the issue could surface,
other cases my not be observed in normal boot flow. Depending on the
size of various sections, and location of relocations within __rel_dyn
and the compiler/linker the outcome of this bug can differ greatly.
This change makes the dram_init* functions use a generic implementation
of decoding and populating memory bank and size data.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Fixes: 758f29d0f8 ("ARM: zynq: Support systems with more memory banks")
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This reverts commit 3edc0c252257e4afed163a3a74aba24a5509b198, reversing
changes made to bb135a0180c31fbd7456021fb9700b49bba7f533.
|
|
|
|
The dram_init* functions for the zynq board are not safe for use from
the board_init_f stage due to its use of the 'tmp' static variable.
This incorrect use of a static variable was causing rare issues where
the dram_init function would overwrite some parts the __rel_dyn section
which caused obscure failures.
Using the zynq_zybo configuration, U-Boot would generate the following
error during image load. This was caused due to dram_init overwriting
the relocations for the "image" variable within the do_bootm function.
Out of coincidence the un-initialized memory has a compression type
which is the same as the value for the relocation type R_ARM_RELATIVE.
Uncompressing Invalid Image ... Unimplemented compression type 23
It should be noted that this is just one way the issue could surface,
other cases my not be observed in normal boot flow.
This change removes the existing code and copies the implementation of
the dram_init and dram_init_banksize from the
arch/arm/mach-uniphier/dram_init.c source. This version of these
functions does not use static variables and behaves the same (reading
banks from fdt, and using the first bank as the ram_size).
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Fixes: 758f29d0f8 ("ARM: zynq: Support systems with more memory banks")
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Zynq 7000S (Single A9 core) devices is using different ID code.
This patch adds this new codes and assign them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This is example how to change u-boot to support more memory banks read
from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is incorrect setting for USB which didn't work with origin
ps7_init_gpl.X files.
Use default setting for Digilent Zybo projects with HDMI in PL.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use space instead of tab in checkboard print to aligned
it with others boards.
Reported-by: David Glessner <david.glessner@rockwellcollins.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
|
|
Move driver to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Move driver to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.
Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Move driver to DM
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Trivial fix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Due to licensing issues, the files ps7_init.c/h are not able to be
distributed with U-Boot source code. Recent Xilinx tools also
provide the GPL variants (ps7_init_gpl.c/h), compatible with U-Boot
license.
Prior to this commit, we had to copy ps7_init files into
board/xilinx/zynq/ before the compile.
To be more user-friendly, let's include ps7_init_gpl.c/h for
Zedboard, MicroZed, ZC702, ZC706.
These init code have been taken from the hwplatform_templates
directory of Xilinx SDK 2014.4.
You can still use customized ps7_init_gpl.c/h by enabling
CONFIG_ZYNQ_CUSTOM_INIT. The recommended directory for storing them
is now board/xilinx/zynq/custom_hw_platform, but board/xilinx/zynq
is still supported for backward compatibility. The latter emits
a warning message to prompt users to gradually switch to the new
directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Prior to this commit, ZC702 and ZC706 shared the same configuration
and were built as follows:
ZC702: make zynq_zc70x_defconfig && make
ZC706: make zynq_zc70x_defconfig && make DEVICE_TREE=zynq-zc706
This commit introduces separate configuration for them, which makes
the next commit much easier.
Going forward, the recommended build commands are:
ZC702: make zynq_zc702_defconfig && make
ZC706: make zynq_zc706_defconfig && make
Although the old work flow is still supported, CONFIG_TARGET_ZC70X
has been marked as deprecated. If used, the warning message is
shown to prompt users to switch to the new scheme.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
