summaryrefslogtreecommitdiff
path: root/board/xilinx
AgeCommit message (Collapse)Author
2018-08-07zynqmp: Add avnet_ultra96_rev1_defconfig to the lits of boardsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-06arm64: zynqmp: Add support for Avnet Ultra96Michal Simek
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files and point to origin internal board name. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06arm: zynq: add support for the zybo z7 boardLuis Araneda
The board is manufactured by Digilent Main features: - Soc: XC7Z010 (Z7-10) or XC7Z020 (Z7-20) - RAM: 1 GB DDR3L - FLASH: 16 MB QSPI - 1 Gbps Ethernet - USB 2.0 - microSD slot - Pcam camera connector - HDMI Tx and Rx - Audio codec: stereo out, stereo in, mic - 5 (Z7-10) or 6 (Z7-20) Pmod ports - 6 push-buttons, 4 switches, 5 LEDs - 1 (Z7-10) or 2 (Z7-20) RGB LEDs Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-08-06microblaze: Add missing quotes around XILINX_MICROBLAZE0_HW_VERMichal Simek
This issue is reported by kconfiglib: warning: style: quotes recommended around default value for string symbol XILINX_MICROBLAZE0_HW_VER (defined at board/xilinx/microblaze-generic/Kconfig:37) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19lib: fdtdec: Rename routine fdtdec_setup_memory_size()Siva Durga Prasad Paladugu
This patch renames the routine fdtdec_setup_memory_size() to fdtdec_setup_mem_size_base() as it now fills the mem base as well along with size. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-07-19arm64: zynqmp: Added support of mmio read and write commandsVipul Kumar
This patch added support of mmio read and write commands. These commands can be used to read and write registers from the u-boot command line. It can be useful in debugging. Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Convert generic platform to DM gpioMichal Simek
Converting GPIO to DM requires to do changes in reset subsystem that's why support for Microblaze soft reset via sysreset and GPIO sysreset support was added. These two patches enables enabling GPIO DM. Microblaze soft reset is bind at last reset method. GPIO reset is handled via sysreset with adding this fragment to DT. gpio-restart { compatible = "gpio-restart"; gpios = <&reset_gpio 0 0 0>; /* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */ }; hard-reset-gpio property is not documented and also handled. Conversion is required. Unfortunately do_reset is required for SPL that's why use only soft microblaze reset for now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Support for watchdog_reset in initShreenidhi Shedi
We should support watchdog reset so that WATCHDOG_RESET will function properly. Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Delete Xilinx watchdog related macrosShreenidhi Shedi
These macros are not required anymore. These will be taken from configuration file. Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Cosmetic changes in Microblaze related filesShreenidhi Shedi
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19arm64: zynqmp: Changed zynqmp command to handle subcommands with ↵Vipul Kumar
U_BOOT_CMD_MKENT This patch changed zynqmp command to handle subcommands with U_BOOT_CMD_MKENT. Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19arm: zynq: Try to enable the first watchdog via aliasesMichal Simek
The same change as was done for zynqmp with this description: Add support for enabling the first watchdog pointed via aliases. DT fragment: aliases { ... watchdog0= &watchdog0; watchdog1 = &watchdog_lpd; ... }; <zynqmp example removed> Till this patch the first watchdog found in DT was used and started which is not enabling all possible configuration based on user request. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19arm64: zynqmp: Try to enable the first watchdog via aliasesMichal Simek
Add support for enabling the first watchdog pointed via aliases. DT fragment: aliases { ... watchdog0 = &watchdog0; watchdog1 = &watchdog_lpd; ... }; dm tree fragment for above configuration with patch applied: ZynqMP> dm tree Class index Probed Driver Name ----------------------------------------- ... watchdog 0 [ ] cdns_wdt | |-- watchdog@ff150000 watchdog 1 [ + ] cdns_wdt | `-- watchdog@fd4d0000 ... dm uclass fragment: ZynqMP> dm uclass ... uclass 75: watchdog 0 watchdog@ff150000 @ 7df02f40, seq -1, (req 1) 1 * watchdog@fd4d0000 @ 7df02ff0, seq 0, (req 0) ... It is visible that index 1 is IP with seq 0 which means that FPD watchdog (@fd4d0000) is in DT below LPD watchdog (@ff150000). Till this patch the first watchdog found in DT was used and started which is not enabling all possible configuration based on user request. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Remove unused XILINX_BOARD_NAME macroMichal Simek
This macro is not used anywhere that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19microblaze: Guard do_reset by CONFIG_SYSRESETMichal Simek
sysreset uclass have own do_reset function which should be used instead of board/platform specific. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19xilinx: zynq: Add support to secure imagesSiva Durga Prasad Paladugu
This patch basically adds two new commands for loadig secure images. 1. zynq rsa adds support to load secure image which can be both authenticated or encrypted or both authenticated and encrypted image in xilinx bootimage(BOOT.bin) format. 2. zynq aes command adds support to decrypt and load encrypted image back to DDR as per destination address. The image has to be encrypted using xilinx bootgen tool and to get only the encrypted image from tool use -split option while invoking bootgen. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19arm/arm64: zynq/zynqmp: pass the PS init file as a kconfig variableLuca Ceresoli
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on ZynqMP (PS init for short). The current logic to locate this file for both platforms is: 1. if a board-specific file exists in board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c then use it 2. otherwise use board/xilinx/zynq/ps?_init_gpl.c In the latter case the file does not exist in the U-Boot sources and must be copied in the source tree from the outside before starting the build. This is typical when it is generated from Xilinx tools while developing a custom hardware. However making sure that a board-specific file is _not_ found (and used) requires some trickery such as removing or overwriting all PS init files (e.g.: the current meta-xilinx yocto layer). This generates a few problems: * if the source tree is shared among different out-of-tree builds, they will pollute (and potentially corrupt) each other * the source tree cannot be read-only * any buildsystem must add a command to copy the PS init file binary * overwriting or deleting files in the source tree is ugly as hell Simplify usage by allowing to pass the path to the desired PS init file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute path or relative to $(srctree). If the variable is set, the user-specified file will always be used without being copied around. If the the variable is left empty, for backward compatibility fall back to the old behaviour. Since the issue is the same for Zynq and ZynqMP, add one kconfig variable in a common place and use it for both. Also use the new kconfig help text to document all the ways to give U-Boot the PS init file. Build-tested with all combinations of: - platform: zynq or zynqmp - PS init file: from XILINX_PS_INIT_FILE (absolute, relative path, non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/ - building in-tree, in subdir, in other directory Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Nathan Rossi <nathan@nathanrossi.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15arm64: zynqmp: Check return value from callocMichal Simek
calloc() can fail and return NULL. The patch is checking return value and return in case of error. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15arm: zynq: Add missing watchdog headerMichal Simek
Add missing header detected by sparse. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Setup the first boot_target at run timeMichal Simek
Detect mmc alias at run time for setting up proper boot_targets sequence. The first target has to correspond with boot mode. The purpose of this patch is to get rid of CONFIG_ZYNQ_SDHCI0/1 parameters in full U-Boot. Unfortunately this patch can't remove it because there is missing mmc implementation for SPL_DM_SEQ_ALIAS. Also xilinx_zynqmp.h only setup boot commands for mmc0 and mmc1. It means using aliases with higher number won't work. But switching between mmc0 and mmc1 should work properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-05-31arm64: zynqmp: Show reset reasonMichal Simek
Read reset reason reg and show it in log and also save it as variable. Clearing reset reason when it is read to show only one status Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-18arm64: zynqmp: Use DWC3 generic driver and DM_USBMichal Simek
Remove harcoded XHCI lists and detect mode, speed based on DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Serial-changes: 2 - Remove also XHCI macros from hardware.h - Remove additional new line in zcu106
2018-05-11SPDX: Correct SPDX tags from recent xilinx mergeTom Rini
Correct the SPDX tag format. Fixes: 3b52847a451a ("Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-11Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.07 microblaze: - Align defconfig zynq: - Rework fpga initialization and cpuinfo handling zynqmp: - Add ZynqMP R5 support - Wire and enable watchdog on zcu100-revC - Setup MMU map for DDR at run time - Show board info based on DT and cleanup IDENT_STRING zynqmp tools: - Add read partition support - Add initial support for Xilinx bif format for boot.bin generation mmc: - Fix get_timer usage on 64bit cpus - Add support for SD3.0 UHS mode nand-zynq: - Add support for 16bit buswidth - Use address cycles from onfi params scsi: - convert ceva sata to UCLASS_AHCI timer: - Add Cadence TTC for ZynqMP r5 watchdog: - Minor cadence driver cleanup
2018-05-11mmc: zynq_sdhci: Add support for SD3.0Siva Durga Prasad Paladugu
This patch adds support of SD3.0 for ZynqMP. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm: zynqmp: Add ZynqMP minimal R5 supportMichal Simek
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot. This patch is adding minimal support to get U-Boot boot. U-Boot on R5 runs out of DDR with default configuration that's why DDR needs to be partitioned if there is something else running on arm64. Console is done via Cadence uart driver and the first Cadence Triple Timer Counter is used for time. This configuration with uart1 was tested on zcu100-revC. U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200) Model: Xilinx ZynqMP R5 DRAM: 512 MiB WARNING: Caches not enabled MMC: In: serial@ff010000 Out: serial@ff010000 Err: serial@ff010000 Net: Net Initialization Skipped No ethernet found. ZynqMP r5> There are two ways how to run this on ZynqMP. 1. Run from ZynqMP arm64 tftpb 20000000 u-boot-r5.elf setenv autostart no && bootelf -p 20000000 cpu 4 disable && cpu 4 release 10000000 lockstep or cpu 4 disable && cpu 4 release 10000000 split 2. Load via jtag when directly to R5 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Simplify boot_target variable compositionMichal Simek
Call calloc for space allocation only at one location and include if/else to sprintf. This will simplify run time device adding based on id aliases. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-05-11arm64: zynqmp: Setup MMU map for DDR at run timeNitin Jain
This patch fills the MMU map for DDR at run time based on information read from Device Tree or automatically detected from static configuration. The patch is needed because for systems which has for example 1GB of memory but MMU map is 2GB there could be spurious accesses which was seen in past when mapping is not fitting with actual memory installed. Signed-off-by: Nitin Jain <nitin.jain@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Wire watchdog internalsMichal Simek
Enable watchdog in full U-Boot. Similar changes were done by: "arm: zynq: Wire watchdog internals" (sha1: e6cc3b25d721c3001019f8b44bfaae2a57255162) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Reset FPD Watchdog on zcu100Michal Simek
Low level configuration didn't reset FPD Watchdog that's why accessing it caused u-boot hang. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm64: zynqmp: Add new defconfig for zc1275 revBSiva Durga Prasad Paladugu
This patch enables support zc1275 revB board. It has SD added compared to revA. The same configuration will work for RevC boards aswell. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm: zynq: Remove checkboard and enable DISPLAY_CPUINFOMichal Simek
Now that showing silicon version is part of the CPU info display, let's remove checkboard(). Note that the generic show_board_info() will still show the DT 'model' property. For instance: U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200) CPU: Zynq 7z045 Silicon: v1.0 Model: Zynq ZC706 Development Board I2C: ready Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>, and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> mini configuration doesn't need to show this information. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-11arm: zynq: Rework FPGA initializationMichal Simek
This commit moves the FPGA descriptor definition to mach-zynq, where it makes more sense. Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar> and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-10SPDX: Convert a few files that were missed beforeTom Rini
As part of the main conversion a few files were missed. These files had additional whitespace after the '*' and before the SPDX tag and my previous regex was too strict. This time I did a grep for all SPDX tags and then filtered out anything that matched the correct styles. Fixes: 83d290c56fab ("SPDX: Convert all of our single license tags to Linux Kernel style") Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-23arm: zynq: Wire automatic ddr detection for Zynq and ZynqMP caseMichal Simek
When static memory configuration is used U-Boot has capability to detect memory size in setup range. Enable this feature for static configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for Xilinx zcu106-revAMichal Simek
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu104 customer boardMichal Simek
Xilinx zcu104 is another customer board. It is sort of zcu102 clone with some differences. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc12xx boardsMichal Simek
Add support for zc12xx boards. All of them are internal boards for silicon validation and share very similar base platforms. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zc1751 dc3Michal Simek
zc1751 is based board with dc3 extenstion card which is used for silicon validation. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add support for zcu100 aka Ultra96 boardMichal Simek
Add support for Xilinx zcu100. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add low level initialization for zc1751Michal Simek
Add psu init for zc1751 dc cards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09arm64: zynqmp: Add low level initialization for zcu102-revAMichal Simek
Add psu init for zcu102-revA. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23MAINTAINERS: Fix Zynq/ZynqMP and Microblaze fragmentsMichal Simek
Fix my fragments to list all files in the repo. Also fix path to for Xilinx Zynq SoC (mach-zynq) It should be the part of "ARM: zynq: move SoC sources to mach-zynq" (sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc) And cover dts files in board MAINTAINERS files. Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm64: zynqmp: Add support for verifying secure imagesSiva Durga Prasad Paladugu
This patch adds new command "zynqmp" to handle zynqmp specific commands like "zynqmp secure". This secure command is used for verifying zynqmp specific secure images. The secure image can either be authenticated or encrypted or both encrypted and authenticated. The secure image is prepared using bootgen and will be in xilinx specific BOOT.BIN format. The optional key can be used for decryption of encrypted image if user key was specified while creation BOOT.BIN. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm64: zynqmp: Correct EG/EV part detection logicSiva Durga Prasad Paladugu
The vcu disable bit in efuse ipdisable register is valid only if PL powered up so, consider PL powerup status for determing EG/EV part. If PL is not powered up, ignore EG/EV part of string. The PL powerup status will be filled by pmufw based on PL PROGB status in the 9th bit of version field. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm: zynq: Wire watchdog internalsMichal Simek
Watchdog is only enabled in full u-boot. Adoption for SPL should be also done because that's the right place where watchdog should be enabled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23arm64: zynqmp: Add support to load an app at EL1Nitin Jain
This patch is adding support to switch to EL1 while loading an EL1 application with u-boot running at EL above EL1 in aarch64 mode. Signed-off-by: Nitin Jain <nitinj@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm: zynq: Update years in copyright to reflect latest changesMichal Simek
Updating year in zynq files. Also add missing Copyright to board.c. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-30arm64: zynqmp: Add psu_init for zcu102-rev1.0Michal Simek
Add low level initialization for zcu102-rev1.0. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit (git 2.34.1) at 2024-12-29 17:39:55 +0000