summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2018-06-18board: Adjust K+P script to run misc (per board) adjustmentsLukasz Majewski
This change gives the opportunity to adjust Linux command line for the imx53 device with some legacy data. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18board: imx53: Always disable display before starting kernelLukasz Majewski
This patch prevents from the situation where we may end up with garbage displayed on the LCD panel. Such situation occurs when one performs "reboot -f" in Linux and then stop in U-boot (or observe the garbage on the screen during boot up). To prevent from such situation - the PWM pin is configured as GPIO and set to LOW. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: Add missing environment.h include to avoid warningLukasz Majewski
Without this change the following warning shows up when building: board/liebherr/display5/display5.c:270:3: warning: implicit declaration of function ‘eth_env_set_enetaddr’ [-Wimplicit-function-declaration] This commit fixes this issue. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: net: Add function to read ethaddr from iMX6 fusesLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: ddr: Enable support for DDR3 auto calibrationLukasz Majewski
This code performs DDR3 memory calibration for display5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: wdt: Enable WDT support (both SPL and u-boot)Lukasz Majewski
Test case: The fitImage gets corrupted: truncate -c -s 3M fitImage run tftp_mmc_fitImg setenv boot_os y reset [board shall hang in SPL with "Trying to boot from MMC1" information] Then after X seconds WDT is causing board to reset. After N boot attempts we enter recovery mode. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: Support for the emergency PAD pressingLukasz Majewski
To enter the special mode, one needs to short cut two pads with e.g. screw driver. After power up the SPL will execute u-boot in which proper actions will be taken. It is worth noting that we do not alter envs (even the BOOT_FROM variable) and unconditionally go to recovery. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: spl: Check return code of the env_* functionsLukasz Majewski
Force booting through u-boot proper when environment error encountered (as a result of either broken SPI-NOR or erased envs). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-17x86: Rename efi-x86 target to efi-x86_appBin Meng
To avoid confusion, let's rename the efi-x86 target to efi-x86_app. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-06-17x86: efi: payload: Add EFI framebuffer driver supportBin Meng
This turns on the EFI framebuffer driver support so that a graphics console can be of additional help. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-06-17x86: baytrail: Drop EFI-specific test logicsBin Meng
Now that we have generic EFI payload support, drop EFI-specific test logics in BayTrail Kconfig and codes, and all BayTrail boards too. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-06-17x86: Drop QEMU-specific EFI payload supportBin Meng
Now that we have generic EFI payload support for all x86 boards, drop the QEMU-specific one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-06-17x86: Add generic EFI payload supportBin Meng
It is possible to create a generic EFI payload for all x86 boards. The payload is configured to include as many generic drivers as possible. All stuff that touches low-level initialization are not allowed as such is the EFI BIOS's responsibility. Platform specific drivers (like gpio, spi, etc) are not included. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-06-17Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-06-16sun50i: h5: Add initial Orange Pi Zero Plus supportHauke Mehrtens
Orange Pi Zero Plus is an open-source single-board computer using the Allwinner H5 SOC. H5 Orangepi Zero Plus has - Quad-core Cortex-A53 - 512MB DDR3 - micrSD slot - 16MBit SPI Nor flash - Debug TTL UART - 1GBit/s Ethernet (RTL8211E) - Wifi (RTL8189FTV) - USB 2.0 Host - USB 2.0 OTG + power supply The device tree file is copied from the Linux kernel 4.17. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16sun8i: h2: Add initial Orange Pi R1 supportHauke Mehrtens
Orange Pi R1 is an open-source single-board computer using the Allwinner H2+ SOC. H2+ Orange Pi R1 has - Quad-core Cortex-A7 - 256MB DDR3 - micrSD slot - 128MBit SPI Nor flash - Debug TTL UART - 100MBit/s Ethernet (H2+) - 100MBit/s Ethernet (RTL8152B) - Wifi (RTL8189ETV) - USB 2.0 OTG + power supply This board is very similar to the Orange Pi Zero. The device tree file is copied from the Linux kernel 4.17. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16ARM: rmobile: Fix CPGW address on V3M EagleMarek Vasut
Fix the CPGWPR/CPGWPCR register address on V3M Eagle to unlock access to the CPG clock control registers. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-06-15Merge tag 'arc-updates-for-2018.07-rc2' of git://git.denx.de/u-boot-arcTom Rini
Here we just add a tool for HSDK flashable images preparation together with extensive documentation for HSDK board. This will help real-life users to update U-Boot on the board.
2018-06-15ARC: HSDK: Add readmeAlexey Brodkin
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-06-15ARC: HSDK: Add tool and make target to generate bspEugeniy Paltsev
HSDK board has preloader that reads SPI flash pages and searches for a special image header to fetch and load binary. Add tool, make target (bsp-generate) to generate update script and u-boot binary image with header for preloader. Also add script to default environment to apply updates. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-06-15arm64: zynqmp: Check return value from callocMichal Simek
calloc() can fail and return NULL. The patch is checking return value and return in case of error. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15arm: zynq: Add missing watchdog headerMichal Simek
Add missing header detected by sparse. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-13ARM: am3517_evm: Enable SPL_OF_CONTROL and SPL_OF_PLATDATAAdam Ford
The SPL doesn't have much room, so in order to support OF_CONTROL in SPL, we need the extra functionality of SPL_OF_PLATDATA. Adding these features allows us to remove a small part of code without losing the serial port during SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13dra76: fix HDMI HPD pinmuxTomi Valkeinen
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly to all the other DRA7 and AM5 SoCs. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-13dra7/am5: remove CEC pin pull-upTomi Valkeinen
HDMI CEC pins are set to pull-up, but CEC requires no pull. Fix this. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-06-12arm: mvebu: Add Helios4 Armada 38x initial supportDennis Gilmore
The helios4 is built on the SolidRun Armada 38x SOM. The port os based on the ClearFog board, using information from https://github.com/helios-4/u-boot-marvell as well as dtb input from https://github.com/helios-4/linux-marvell Signed-off-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board: Kconfig: Re-Arrangement of PPA firmware and header addressesBhaskar Upadhaya
PPA firmware and header address may vary depending upon different boards, configure ppa firmware and header address in board specific Kconfig. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2018-06-07board: samsung: add missing line breaks for pr_err()Seung-Woo Kim
After the commit 9b643e312d52 ("treewide: replace with error() with pr_err()"), there are some pr_err() with no line break. Add missing line breaks. Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2018-06-07mvebu: turris_omnia: add note about i2c slave disableBaruch Siach
Code that disables the i2c slave is now in the mvtwsi i2c driver. Platform must enable DM_I2C to use that code. Add a comment in the code as a reminder for the planned DM_I2C migration of Turris Omnia. Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-06-05ARM: legoev3: update boot script to load uEnv.txt and .dtbDavid Lechner
This updates the LEGO MINDSTORMS EV3 boot script to try loading a uEnv.txt file and a da850-lego-ev3.dtb device tree during boot. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: disable networkingDavid Lechner
This disables networking related items in the config. The EV3 does not have any networking hardware, so this is wasted space. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: Move UART enable to early initDavid Lechner
This moves the UART init for LEGO MINDSTORMS EV3 to board_early_init_f(). Some console messages were not being printed because the UART was not enabled until later in the init process. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: increase flash image sizesDavid Lechner
This increases the kernel image to 4M and the rootfs image to 10M. It is getting hard to get a kernel image to fit in 3M. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: kirkwood: SBx81LIFKW: Enable network hardwareChris Packham
The SBx81LIFKW boards connect to the internal chassis management network via a Marvell 88e6097 L2 switch. The chassis connections are direct serdes on ports 8 and 9 with a RGMII interface on port 10 connected to the CPU MAC. For debugging purposes ports 0 and 1 are also taken out to headers on the board. Because the debug interfaces are sometimes connected to with straight ribbon cables we need to run them at 10Mbps. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05ARM: add SBx81LIFKW boardChris Packham
This is a series of line cards for Allied Telesis's SBx8100 chassis switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16 and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05arm: mvebu: switch clearfog to use device-tree i2c and gpioJon Nettleton
This switches the clearfog boards to use DM based gpio and i2c drivers. The io expanders are configured via their device-tree entries. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: add DT i2c aliases] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-04MAINTAINERS: Take over DB410c maintainershipRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-06-04Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2018-06-04board: sun50i: Add Amarula A64-Relic initial supportJagan Teki
Amarula A64-Relic is A64 based IoT device, which support - Allwinner A64 Cortex-A53 - Mali-400MP2 GPU - AXP803 PMIC - 1GB DDR3 RAM - 8GB eMMC - AP6330 Wifi/BLE - MIPI-DSI - CSI: OV5640 sensor - USB OTG - 12V DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-06-02Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-06-01Merge tag 'xilinx-for-v2018.07-2' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.07 second pull zynqmp: - Show reset reason - Remove emulation platform - Update pmufw version - Simplify mmc bootmode - Remove dc2 useless configuration file - Cleanup mini config - Defconfig syncup - zcu100, zcu104 and zcu111 dts fixes xilinx: - Use live-tree functions in some drivers - Add support for Avnet Minized and Antminer S9 fpga: - Add secure bitstream loading support mmc: - Add hs200 mode support usb xhci: - Header fix
2018-06-01Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2018-06-01ARM: renesas: Add R8A77990 E3 Ebisu boardMarek Vasut
Add support for the R8A77990 Ebisu board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-31Merge tag 'arc-updates-for-2018.07-rc1' of git://git.denx.de/u-boot-arcTom Rini
Here we do a couple of minor fixes like: - Move .ivt section to the very beginning of the image by default which allows us to use that image put right at reset vector (usually 0x0) - Improve relocation fix-up which became required once we moved .ivt and understood a problem with existing implementation where we relied on a particular placement of sections. Now we don't care about placement because we just explicitly check for .text and in case of ARCompact .ivt sections - Re-implemnt do_reset() such that it calls reset_cpu() which could implmented for a particular board And hte most important part we introduce support for yet another devboard from Synopsys - EMDK.
2018-05-31ARC: Add support for EM Development Kit boardAlexey Brodkin
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is an FPGA-based development platform from Synopsys aimed to speed-up development of software for ARC EM cores and entire subsystems based on ARC EM like Data Fusion, Secure and Sensor & Control subsystems. U-Boot is supposed to be used as a primary bootloader on EMDK allowing users to easily load and start their application from micro-SD card. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
generated by cgit (git 2.34.1) at 2024-12-27 21:10:23 +0000