summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2015-12-13armv8/ls1043ardb: Add support for >2GB memoryShaohui Xie
This patch also expose the complete DDR region(s) to Linux. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13freescale: fman: make sure phy-handle property is big endianShaohui Xie
When creating phy-handle property, an unsigned int value is created by fdt_create_phandle, and memcpy is used to get the value, since DTS is big endian, the value cannot be used directly on little endian SoCs, it should be converted by cpu_to_fdt32. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13armv8/ls2080ardb: Update DDR settings for four chip-select caseYork Sun
When 4 chip-selects are used, vref should use range 1 and CDT uses 80 ohm, and 2T timing is enabled. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-13armv8/ls2080aqds: Update DDR settings for four chip-select caseYork Sun
When 4 chip-selects are used, vref should use range 1 and CDT uses 80 ohm, and 2T timing is enabled. Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-12siemens,am33x: remove ddr3 delay workaroundEgli, Samuel
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de>
2015-12-12stm32: Convert serial driver to DMKamil Lulko
Signed-off-by: Kamil Lulko <kamil.lulko@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-11Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2015-12-11imx: mx7dsabresd: Add QSPI supportPeng Fan
Support qspi flashes for mx7dsabresd 1. introduce pin mux settings 2. enable qspi clock 3. introduce related macro definitions Default QSPI is not enabled, since we need hardware rework to use QSPI, see SPF-28590, page 9: " QSPI signals are muxed with EPDC_D[7:0] When using QSPI: de-populate R388-R391, R396-R399 populate R392-R395, R299, R300 " After hardware rework, define CONFIG_FSL_QSPI in mx7dsabresd.h. qspi flashes can be deteced and read/erase/write. Log info: " => sf probe SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB => sf read 0x80000000 0 0x4000000 device 0 whole chip SF: 67108864 bytes @ 0x0 Read: OK => sf erase 0 0x4000000 SF: 67108864 bytes @ 0x0 Erased: OK => sf write 0x80000000 0 0x4000000 device 0 whole chip SF: 67108864 bytes @ 0x0 Written: OK " Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Adrian Alonso <aalonso@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-12-10sunxi: Add suport for A83T HomletV2 Board by Allwinnervishnupatekar
Add dts and defconfig for h8homletv2 board. H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner. It has UART, ethernet, USB, HDMI, etc ports on it. A83T patches are tested on this board. Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10sunxi: power: enabled support for axp818vishnupatekar
Enabled support for AXP818 in SPL and u-boot. DCDC1, DCDC2, DCDC3 and DCSC5 are enabled. Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10sunxi: Add Machine Support for A83T SOCvishnupatekar
Allwinner A83T is octa-core cortex-a7 SOC. This enables support for A83T. SMP is not yet supported. Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-09x86: Remove HAVE_ACPI_RESUMEBin Meng
These are currently dead codes. Until we have complete ACPI support, we don't know if it works or not. Remove to avoid confusion. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2015-12-09x86: Remove CPU_INTEL_SOCKET_RPGA989Bin Meng
This Kconfig option name indicates it has something to do with cpu socket, however it is actually not the case. Remove it and move options inside it to NORTHBRIDGE_INTEL_IVYBRIDGE. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2015-12-09x86: Clean up ivybridge/chrome Kconfig optionsBin Meng
There are some options which are never used, and also some options which are selected by others but have never been a Kconfg option. Clean these up. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2015-12-07mx6sxsabresd: Fix Ethernet PHY reset sequenceFabio Estevam
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. Fix this by calling enable_fec_anatop_clock() earlier and also by adding a 10ms reset delay as recommended in the AR8031 datasheet. Suggested-by: Jörg Krause <joerg.krause@embedded.rocks> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2015-12-07cgtqmx6eval: Fix defconfig nameOtavio Salvador
After the conversion to SPL the defconfig was renamed, so adjust it. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-12-07Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini
2015-12-07zynq: sdhci: Move driver to DMMichal Simek
Move driver to DM Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-07net: gem: Move driver to DMMichal Simek
- Enable DM_ETH by default for Zynq and ZynqMP - Remove board_eth_init code - Change miiphy_read function to return value instead of error code based on DM requirement - Do not enable EMIO DT support by default Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-07arm: socfpga: Add SoCFPGA SR1500 boardStefan Roese
The SR1500 board is a CycloneV based board, similar to the EBV SoCrates, equipped with the following devices: - SPI NOR - eMMC - Ethernet Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Pavel Machek <pavel@denx.de>
2015-12-05rpi: add support for Raspberry Pi ZeroStephen Warren
For U-Boot's purposes, at present all we care about is ensuring there's a model table entry. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-12-05rpi: fix revision scheme parsingStephen Warren
The RPi has two different schemes for encoding board revision values. When adding RPi 2 support, I thought that the conflicting type field values were to be interpreted based on bcm2835-vs-bcm2836. In fact, the scheme bit determines the encoding. The RPi Zero uses the bcm2835 yet uses the new encoding scheme. Fix the code to cater for this correctly. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-12-05rpi: get rid of BCM2835_BOARD_REV_* macrosStephen Warren
There are two numbering schemes for the RPi revision values; old and new scheme. The values within each scheme overlap. Hence, it doesn't make sense to have absolute/global names for the revision IDs. Get rid of the names and just use the raw revision/type values to set up the array of per-revision data. This change makes most sense when coupled with the next change. However, it's split out so that the mechanical cut/paste is separate from the logic changes for easier review and problem bisection. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-12-05Change e-mail address of Kamil LulkoKamil Lulko
Signed-off-by: Kamil Lulko <kamil.lulko@gmail.com>
2015-12-04Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-12-01arm: imx6: novena, gw_ventana: Fix use of pfuze100 bit definitionsMarek Vasut
The following patch changed the PFUZE100 swbst register bit definitions and broke PMIC configuration on multiple boards, at least on the novena and gw_ventana. This patch fixes it. commit 8fa46350a4c7dca7710362f6c871098557b934ad Author: Peng Fan <Peng.Fan@freescale.com> Date: Fri Aug 7 16:43:45 2015 +0800 power: regulator: add pfuze100 support Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Peng Fan <Peng.Fan@freescale.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Vagrant Cascadian <vagrant@aikidev.net> Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com> Tested-by: Vagrant Cascadian <vagrant@aikidev.net> Reviewed-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Tim Harvey <tharvey@gateworks.com>
2015-12-01rockchip: Add basic support for evb-rk3036 boardhuang lin
This add some basic files required to allow the board to dispaly serial message and can run command(mmc info etc) Signed-off-by: Lin Huang <hl@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org> Moved board Kconfig fragment from previous patch into this one to fix build error: Signed-off-by: Simon Glass <sjg@chromium.org> Series-changes: 8 - moved board Kconfig fragment from previous patch into this one
2015-11-30Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2015-11-30arm: atmel: Add SAMA5D2 Xplained boardWenyou Yang
The board supports following features: - Boot media support: SD card/e.MMC/SPI flash, - Support LCD display (optional, disabled by default), - Support ethernet, - Support USB mass storage. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> [fix checkpatch warnings] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-11-30Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2015-11-30board/ls2080qds: Fix typo in README for QSGMII riser cardPrabhakar Kushwaha
DPMACx to PHY mapping for SGMII is mentioned as QSGMII. So fix typo in README for QSGMII rise card. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: Change from ls2085aqds to ls2080aqds] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8/ls1043ardb: add USB supportGong Qianyu
Add support for the third USB controller for LS1043A. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8/ls1043aqds: add LS1043AQDS board supportShaohui Xie
LS1043AQDS Specification: ------------------------- Memory subsystem: * 2GByte DDR4 DIMM * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two RGMII ports * XFI 10G port * SGMII * QSGMII with 4x 1G ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> [York Sun: Add CONFIG_SYS_NS16550=y in defconfig] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8: ls2085a: Add support of LS2085A SoCPrabhakar Kushwaha
Freescale's LS2085A is a another personality of LS2080A SoC with support of AIOP and DP-DDR. This Patch adds support of LS2085A Personality. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: Updated MAINTAINERS files Dropped #ifdef in cpu.h Add CONFIG_SYS_NS16550=y in defconfig] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8: LS2080A: Rename LS2085A to reflect LS2080APrabhakar Kushwaha
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc. So renaming existing LS2085A code base to reflect LS2080A (Prime personality) Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: Dropped #ifdef in cpu.c for cpu_type_list] Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30driver: net: fsl-mc: Create DPAA2 object at run-timePrabhakar Kushwaha
Freescale's DPAA2 ethernet driver depends upon the static DPL for the DPRC, DPNI, DPBP, DPIO objects. Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30armv8: ls2085aqds: Print function name during SerDes errorPrabhakar Kushwaha
Print function name along with SerDes Protocol during SerDes Protocol not supported error. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30Merge git://git.denx.de/u-boot-socfpgaTom Rini
2015-11-30arm: socfpga: Repair SoCrates boardMarek Vasut
This board was constantly parasiting on the CV SoCDK, so split it into it's own separate directory. Moreover, the board config was missing important bits, like simple-bus support in SPL, the DRAM configuration was incorrect and the DTS was also missing the pre reloc bits. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Dinh Nguyen <dinh.linux@gmail.com> Cc: Jan Viktorin <viktorin@rehivetech.com>
2015-11-30Merge git://www.denx.de/git/u-boot-ppc4xxTom Rini
2015-11-30PPC4xx: Create "liebherr" vendor directoryWolfgang Denk
In preparation of some new Liebherr boards to be added soon, a new "liebherr" vendor directory gets created, and the "lwmon5" board directory is moved into this new vendor directory. cc: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2015-11-29arm: kirkwood: add ZyXEL NSA310S deviceGerald Kerma
This patch add ZyXEL NSA310S 1-Bay Media Server The ZyXEL NSA310S device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1000Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: PHY Marvell 88E1318 - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 4 Status LED (green) - 1 Copy/Sync button - 1 Reset button - 1 SATA II port - 2 USB 2.0 ports (front and back) - Smart fan Signed-off-by: Gerald Kerma <dreagle@doukki.net> Signed-off-by: Tony Dinh <mibodhi@gmail.com> Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
2015-11-25colibri_vf: Add board_usb_phy_mode functionSanchayan Maity
Add board_usb_phy_mode function for detecting whether a port is being used as host or client using a GPIO. On Colibri Vybrid we provide GPIO 102 for this very same purpose. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2015-11-25cgtqmx6eval: Add SPL supportOtavio Salvador
Congatec has several MX6 boards based on quad, dual, dual-lite and solo. Add SPL support so that all the variants can be supported Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-25cgtqmx6eval: Add SPI NOR flash supportOtavio Salvador
Add SPI NOR support: => sf probe SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-22Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2015-11-22sunxi: Add support for the Lamobo R1 boardJelle de Jong
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such on the PCB, is meant as a A20 based router board. As such the board comes with a built-in switch chip giving it 5 gigabit ethernet ports, and it has a large empty area on the pcb with mounting holes which will fit a 2.5 inch harddisk. To complete its networking features it has a Realtek RTL8192CU for WiFi 802.11 b/g/n. The dts file is identical to the one submitted upstream. Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22sunxi: Add support for Orangepi Plus and Orangepi PC boardsHans de Goede
Add defconfig files for the Orangepi Plus and Orangepi PC. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22sunxi: Add H3 DRAM initialization supportJens Kuske
Based on existing A23/A33 code and the original H3 boot0. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22sunxi: Add basic H3 supportJens Kuske
Add initial sun8i H3 support, only uart + mmc are supported for now. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>