summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-07-15sun8i: h3: Add support for the Beelink-x2 STBMarcus Cooper
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot, 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a dual colour LED and an optical S/PDIF connector. Linux commit details about the sun8i-h3-beelink-x2.dts sync: "ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2" (sha1: cc4bddade114b696ab27c1a77cfc7040151306da) Signed-off-by: Marcus Cooper <codekipper@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-13ARM: davinci: da850: Manual pinmux only when PINCTRL not availableAdam Ford
With a recent update to the pinctrl-single driver and the fact that the da850evm has both DM and OF_CONTROL working in both SPL and U-Boot, some of the manual pinmuxing can be setup to only be activated when either the driver doesn't have DM for it, or when CONFIG_PINMUX isn't available (only during SPL). If the code ever shrinks enough to support PINCTRL in SPL, a lot of this can go away. This also remove some manual pinmuxing not needed by SPL to give SPL a little more breathing room. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13ARM: am335x: Add phyCORE AM335x R2 supportNiel Fourie
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec phyBOARD-Wega AM335x. CPU : AM335X-GP rev 2.1 Model: Phytec AM335x phyBOARD-WEGA DRAM: 256 MiB NAND: 256 MiB MMC: OMAP SD/MMC: 0 eth0: ethernet@4a100000 Working: - Eth0 - i2C - MMC/SD - NAND - UART - USB (host) Device trees were taken from Linux mainline: commit 37624b58542f ("Linux 5.1-rc7") Signed-off-by: Niel Fourie <lusus@denx.de> Signed-off-by: Parthiban Nallathambi <pn@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Marek Vasut <marex@denx.de>
2019-07-13ARM: legoev3: convert to driver modelDavid Lechner
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI and SPI_FLASH are converted. The device tree contains only the minimal nodes required by U-Boot since the size of U-Boot is limited to 256K on this device. Signed-off-by: David Lechner <david@lechnology.com>
2019-07-13ARM: omap3: evm: Enable DM_USB in defconfigDerald D. Woods
This addresses the following warning message: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/MIGRATION.txt for more info. ==================================================== As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be readily adapted. There is some additional 'gpio-hog' support needed to fully setup USB in a similar manner to Linux. Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-12board: pm9263: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEOIlko Iliev
Convert the board to support the USB and video driver model and remove the unnecessary code.
2019-07-12board: pm9261: Convert to CONFIG_DM_USB and CONFIG_DM_VIDEOIlko Iliev
Convert the board to support the USB and video driver model and remove the unnecessary code.
2019-07-11Merge tag 'dm-pull-9jul19-take2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-dm - Sandbox improvements including .dts refactor - Minor tracing and PCI improvements - Various other minor fixes - Conversion of patman, dtoc and binman to support Python 3
2019-07-11km/spi: remove deprecated SPI flash driver code for KM Kirkwood boardsPascal Linder
KM Kirkwood boards now implement the driver model for its SPI flash interface. Therefore, the old board specific claim and release functions can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet unused as well. All its appearances and dependencies are removed in the kirkwood_spi driver, header files and finally the configuration whitelist. Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11km/spi: activate driver model for SPI flash on KM Kirkwood boardsPascal Linder
The corresponding configurations are selected in the common Kconfig file. This is easier than changing every affected board default configuration file. The default configuration for the PORTL2 board, however, still needs some modifications to correctly use the driver model. Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11km/spi: overwrite kirkwood_spi weak functions for KM Kirkwood boardsPascal Linder
As the SPI NOR and NAND devices share the same hardware pins, the MPP configuration has to be changed when claiming/releasing the bus. The current configuration is saved when claiming and restored when releasing. Furthermore, a general-purpose output is used to switch the chip-select signal. This is now also implemented for the DM part of the kirkwood_spi driver. Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11km: modify Kconfig file organization for KM boardsPascal Linder
As preparation for the upcoming transferring of configurations from header files to Kconfig, a common Kconfig file for all KM boards was created. For the moment, it only sources the other three, more specific, Kconfig files. Therefore, the architecture Kconfig files now include the common Kconfig file. Also, the configuration selection for KM boards was moved from the architecture Kconfig files to the board specific Kconfig files. Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch> Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Cc: Mario Six <mario.six@gdsys.cc> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11arm: mvebu: turris_omnia: fix rescue mode bootcmd bootargs settingMarek Behún
Rescue mode bootcmd currently only appends the "omniarescue" parameter to the bootargs variable. We do not want the user to be able to change rescue mode bootargs. Therefore change this so that bootcmd sets the bootargs variable in an absolute way (adding console device information and the omniarescue paramterer). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11arm: mvebu: turris_omnia: call pci_init from board init codeMarek Behún
We always want to enumerate PCIe devices, because withouth this they won't work in Linux. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11arm: mvebu: turris_omnia: fix adapters MAC addressesMarek Behún
The board code reads MAC addresses from the ATSHA204A cryptochip. For compatibility reasons the ethernet adapters on this SOC are not enumerated in register address order. But when Omnia was first manufactured this was done differently. Change setting of MAC addresses to conform to the description on the stickers sticked on actual Omnias. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-11arm: mvebu: clearfog: document boot from SATABaruch Siach
Document the main U-Boot image offset when booting from SATA disk on the Clearfog board. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2019-07-10sandbox: Add documentation on how to run valgrindSimon Glass
U-Boot sandbox can run with valgrind to check memory allocations. Add documentation on how to do this. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-07-10sandbox: Allo sdl-config to be overriddenSimon Glass
When cross-compiling, sometimes sdl-config must come from a different path from the default. Add a way to override it, by adding SDL_CONFIG to the environment before building U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-07-09Merge tag 'u-boot-atmel-2019.10-a' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel features and fixes for 2019.10 cycle This includes the Atmel QSPI driver and support for the at91 boards. This is the port of the driver from Linux, mostly done by Tudor Ambarus.
2019-07-09configs: sama5d27_som1_ek: add qspiflash_defconfigTudor Ambarus
Add the default config file of QSPI media. The config is based on sama5d27_som1_ek_mmc_defconfig. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-09configs: sama5d2_xplained: add qspiflash_defconfigTudor Ambarus
Add the default config file of QSPI media. The config is based on sama5d2_xplained_mmc_defconfig. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-08Merge tag 'u-boot-amlogic-20190704' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - fix khadas-vim README - add support for unique generated MAC adresses from SoC serial, limited to Amlogic GXL/GXM boards for now
2019-07-08Merge tag 'mmc-6-23' of https://github.com/MrVan/u-bootTom Rini
- Pull in the series to split fsl_esdhc for i.MX/non-i.MX cleanly
2019-07-04board: amlogic: add mailing-list to MAINTAINERSNeil Armstrong
Add missing mailing-list to the amlogic boards MAINTAINERS file. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04board: amlogic: Generate unique MAC address for Q200 and P212 based boardsNeil Armstrong
Enable unique MAC address generation for boards usins SoCs having a known functional and valid unique serial number. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04board: amlogic: vim: Fix READMEAndreas Färber
Unlike the BayLibre repos Khadas' repo defaults to using native gcc, so specify the CROSS_COMPILE setting matching the prescribed toolchain. Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-07-04wandboard: README: Adjust the U-Boot proper binary nameFabio Estevam
After the conversion to DM the U-Boot proper binary name is 'u-boot-dtb.img', so adjust it accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-07-04wandboard: Add FIT image supportFabio Estevam
After the transition to DM, only the mx6dl/solo wandboard is supported. Add FIT image support so that all the wandboard variants can be supported, like it was prior to the DM conversion. Successfully booted Linux on mx6q/solo/qp wandboards. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-07-01Merge tag 'u-boot-atmel-fixes-2019.07-b' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel fixes for 2019.07 cycle
2019-06-28Merge tag 'u-boot-imx-20190628' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2019.07 - menlo board - allow SDB on Sabre - HAB for mx6sl - apalis board
2019-06-28ARM: imx: m53menlo: Convert to DM VIDEOMarek Vasut
Enable DM Video support on iMX53 M53Menlo and fix minor details to restore previous behavior of the system. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-06-27ARM: imx: m53menlo: Convert MMC, USB and block to DMMarek Vasut
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo . Convert board code to match the DM support. This also enables DM pincontrol to configure the SDHI pins. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-06-27ARM: imx: m53menlo: Enable DM GPIOMarek Vasut
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where applicable. Enable MALLOC_F to let the GPIO controllers bind early on. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-06-27pico-imx7d: README: Adjust the binary name after DM conversionFabio Estevam
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx, so fix the README file accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Joris Offouga <offougajoris@gmail.com>
2019-06-27board: atmel: fix pda variable not being resetEugen Hristev
In case someone detects a PDA and u-boot sets the 'pda' variable, and the user does a saveenv, the pda is set in env, and if the screen is removed, u-boot will still have in the env the 'pda' variable, even if no screen is attached. In order to fix this, we have to reset the 'pda' variable, such that it's not just set if the screen is detected, but also unset if no screen is detected. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-06-26rockchip: rk3399: Fix enabling boot-on regulatorsMark Kettenis
The new common rockchip pinctrl driver does not support explicit requests for a particular pinctrl function. As a result, the board_init() function bails out early before enabling the boot-on regulators. Fix this by simply removing the request for pwm0, pwm2 and pwm3. The generic DM code already does the necessary configuration if necessary. Reported-by: Levin Du <djw@t-chip.com.cn> Signed-of-by: Mark Kettenis <kettenis@openbsd.org>
2019-06-26rockchip: rk3399: Support common spl_board_initJagan Teki
Support common spl_board_init by moving code from puma board file into, common rk3399-board-spl.c. Part of the code has sysreset-gpio, regulators_enable_boot_on but right now only puma board is using this with relevant config options rest remains common for all targets. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26board: rk3399: Drop explicit uart enablement in spl_board_initJagan Teki
preloader_console_init is used for printing SPL boot banner that usually called from spl_board_init. The current spl_board_init in evb and rock960 is enabling explicit pinctrl, debug uart prior to calling preloader_console_init which eventually not required since board_init_f is already enabled debug uart. So, drop those explicit enablement calls from spl_board_init of evb, rock960. Tested this by enabling CONFIG_SPL_BOARD_INIT and adding u-boot,dm-pre-reloc property for uart node. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26Kconfig: Add u-boot.itb BUILD_TARGET for RockchipJagan Teki
Add u-boot.itb BUILD_TARGET for Rockchip platform when SPL_LOAD_FIT is being used. This can get rid of building itb explicitly with 'make u-boot.itb' so, from now all required images will build just by make. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26board: puma: Get bl31.bin via BL31 and rk3399m0.bin via PMUM0Jagan Teki
Right now puma rk3399 board need to copy bl31-rk3399.bin and rk3399m0.bin into u-boot source directory to make use of building u-boot.itb. So, add environment variable - BL31 for bl31.bin (instead of bl31-rk3399.bin to compatible with other platform BL31 env) - PMUM0 for rk3399m0.bin If the builds are not exporting BL31, PMUM0 env, the fit_spl_atf.sh will notify with warning about which document to refer for more information like this: WARNING: BL31 file bl31.bin NOT found, resulting binary is non-functional Please read Building section in doc/README.rockchip WARNING: PMUM0 file rk3399m0.bin NOT found, resulting binary is non-functional Please read Building section in doc/README.rockchip Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-26rockchip: rk3328: add rock64-rk3328_defconfigMatwey V. Kornilov
The ROCK64 is a credit card size SBC based on Rockchip RK3328 Quad-Core ARM Cortex A53. This series allow building u-boot SPL and u-boot.itb for Rock64 board. The proprietary TPL is stil required for deploy: ./tools/mkimage -n rk3328 -T rksd \ -d ./rkbin/bin/rk33/rk3328_ddr_333MHz_v1.16.bin idbloader.img cat ./spl/u-boot-spl.bin >> idbloader.img dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-06-23Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-21arm64: zynqmp: Cover ultra96 dts file by MAINTAINERS fragmentMichal Simek
Avnet Ultra96 dts file should be also cover by MAINTAINERS fragment. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-06-21am335x, guardian: update the maintainer listMoses Christopher
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
2019-06-21vexpress64: fix a typo of SPDX-License-IdentifierMasahiro Yamada
Misspelling of SPDX-License-Identifier is rather fatal than other general typos, so must be fixed. This file spells SPDX-Licence-Identifier. ^ I also moved it to the very top of the file with // comment style. Detected by grepping the source tree: $ git grep --not -e SPDX-License-Identifier --and -e SPDX- board/armltd/vexpress64/pcie.c: * SPDX-Licence-Identifier: GPL-2.0+ Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
2019-06-21board: Arcturus: DM: Disable drivers without DM support.Oleksandr Zhadan
Extra "not DM" controllers support is disabled. u-boot BSP still good enough to upgrade and run images. Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com> Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
2019-06-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xxTom Rini
- PCIe driver change to support DM model - T2080QDS migrated to use PCIe DM model
2019-06-20powerpc: T208xQDS: Compile the legacy PCIe routines conditionallyHou Zhiqiang
Compile the legacy PCIe initialization reoutines only when DM_PCI is not enabled. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- LS1046AFRWY support - USB errata fix and secure boot defconfig support for LS1028A - Enabled SDHC and SATA for LX2160 - LS1046A serdes fixes - other minor fixes
2019-06-19board/freescale/common: secure_boot: Set bootdelay to -2.Udit Agarwal
Uboot prompt must not be available while running secure boot. TO ensure this bootdelay must be set to -2. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-06 12:35:29 +0000