summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2015-01-20Merge git://git.denx.de/u-boot-arcTom Rini
2015-01-20MAINTAINERS: add me as the maintainer of mpc837xerdbSinan Akman
Signed-off-by: Sinan Akman <sinan@writeme.com> Cc: Tom Rini <trini@ti.com>
2015-01-20imx: ls102xa: Remove reference to gdataSimon Glass
The global_data pointer (gd) has already been set before board_init_f() is called. We should not assign it again. We should also not use gdata since it is going away. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-20imx: woodburn: Remove reference to gdataSimon Glass
The global_data pointer (gd) has already been set before board_init_f() is called. We should not assign it again. We should also not use gdata since it is going away. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stefano Babic <sbabic@denx.de>
2015-01-20imx: cm_fx6: Remove reference to gdataSimon Glass
The global_data pointer (gd) has already been set before board_init_f() is called. We should not assign it again. We should also not use gdata since it is going away. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2015-01-19ARM: atmel: sama5d4_xplained: add option for usb ethernet gadgetBo Shen
Add the option for USB Ethernet gadget based on atmel usb device. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-01-19ARM: atmel: sama5d4ek: add option for usb ethernet gadgetBo Shen
Add the option for USB Ethernet gadget based on atmel usb device. Signed-off-by: Bo Shen <voice.shen@atmel.com>
2015-01-19arm, at91: corvus board updatesHeiko Schocher
- corvus board fix problems with toshiba nand chips on the corvus board problems with toshiba chips Manufacturer ID: 0x98 Chip ID: 0xdc encounterd. Solve this in the following way: - set other nand timings - enable CONFIG_SYS_NAND_READY_PIN - correct the MACH_TYPE setting Signed-off-by: Heiko Schocher <hs@denx.de>
2015-01-19taurus, spl: erase also spi flash if recovery button is pressedHeiko Schocher
if in SPL mode recovery button is pressed, erase also spi flash from offset 0 to CONFIG_SYS_NAND_U_BOOT_SIZE on the taurus board. Signed-off-by: Heiko Schocher <hs@denx.de>
2015-01-16mpc85xx/t1040qds: convert deep sleep to generic board interfacetang yuantian
A new deep sleep interface is introduced to support generic board structure. Converts it to use new interface. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16mpc85xx/t102xqds: convert deep sleep to generic board interfacetang yuantian
A new deep sleep interface is introduced to support generic board structure. Converts it to use new interface. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16powerpc/t1024rdb: Add support for T1024RDB-PBShengzhou Liu
T1024RDB-PB board adds 2.5G SGMII support with AQR105 PHY. rcw_0x095 is used for 10G XFI + 3x PCIex1 rcw_0x135 is used for 2.5G SGMII + 2x PCIex1 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16mpc85xx/t102xrdb: convert deep sleep to generic board interfacetang yuantian
A new deep sleep interface is introduced to support generic board structure. Converts it to use new interface. Besides, added SPI/SD/NAND boot deep sleep support. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16powerpc: SECURE BOOT- Add secure boot target for T1042RDBgaurav rana
Secure boot target is added for T1042RDB platform. Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16powerpc/t4240rdb: Add alternate SerDes 2 protocol to align with RCWChunhe Lan
SerDes 2 protocol 56 is not valid any longer due to the new RCW; protocol 55 is used instead, so add SerDes 2 protocol 55 to align with RCW. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16powerpc/mpc85xx: SECURE BOOT- Add secure boot target for P5040DSgaurav rana
Secure boot target is added for P5040DS platform. Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16powerpc/c29xpcie: Add secure boot supportPo Liu
Add NOR and SPI flash secure boot target for C29XPCIE board. Signed-off-by: Po Liu <Po.Liu@freescale.com> Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini
2015-01-16powerpc: 74xx_7xx: remove 74xx_7xx cpu supportMasahiro Yamada
All the 74xx_7xx boards are still non-generic boards: P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2 Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Nye Liu <nyet@zumanetworks.com> Cc: Roy Zang <tie-fei.zang@freescale.com>
2015-01-15board/synopsys: remove selection of CPU from the boardAlexey Brodkin
Both ARCangel4 and AXS10x are FPGA-based boards so they may have different CPUs. For now we have only 1 option (ARC700) and we define this as default in arch Kconfig. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-01-14Add support for Seagate BlackArmor NAS220Evgeni Dobrev
Add support for Seagate BlackArmor NAS220 Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
2015-01-14sunxi: usbc: Add support for usb0 to the common usbc codeHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: video: Add support for external DAC enable pinChen-Yu Tsai
The external DAC for VGA output might have either a power or reset control pin that needs to be pulled up, as is the case on the Hummingbird A31. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sunxi: video: Allow external DACs for VGA on platforms without TV encodersChen-Yu Tsai
Using an external DAC for VGA output was available on sun5i. Since some other SoCs don't have a builtin TV encoder, but might have use for a VGA output, enable the option for the platforms that don't have TV encoders. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sunxi: video: Add lvds supportHans de Goede
Add support for lvds lcd panels Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de>
2015-01-14sunxi: add Linksprite pcDuino v1/v2 supportZoltan HERPAI
Add support for a sun4i board built by Linksprite. This addition covers both v1 and v2 versions. As the board has been working with 408MHz memory setting in the u-boot-sunxi branch, and has been proven to be running stable during my tests as well, a respective new DRAM config file is added as well. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sunxi: video: Add VGA output supportHans de Goede
Add support for VGA directly from the sunxi SoC / display engine. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: video: Add support for VGA via external DACs connected to the LCD pinsHans de Goede
Add support for external DACs connected to the parallel LCD interface driving a VGA connector, such as found on the Olimex A13 boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: video: Enable video on sun8i, which supports LCD but not HDMIHans de Goede
The A23 (sun8i) only has lcd output support, so allow building the video code without HDMI support for use with the A23. Also the A23 has the same reset bits (and necessity to enable the DRC block) as the sun6i, so enable those bits for sun8i too. Note building without HDMI support is useful for the A13 (sun5i variant) too, as that one does not have HDMI either. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: video: Add lcd output supportHans de Goede
Add lcd output support, see the new Kconfig entries and doc/README.video for how to enable / configure this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun7i: Add new Bananapro board / defconfigHans de Goede
Add support for the new Bananapro A20 development board from lemaker.org. This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver, 3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun7i: Add defconfig for MSI Primo73 tabletSiarhei Siamashka
This patch uses the same DRAM settings as in the pre-installed Android firmware. The LCD display is supported too. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sun6i: Add defconfig for MSI Primo81 tabletSiarhei Siamashka
This patch uses the same ZQ and DRAM clock settings as in the pre-installed Android firmware. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sunxi: Fix CONFIG_UART0_PORT_F build and add it to menuconfigSiarhei Siamashka
The CONFIG_UART0_PORT_F option has been supported since http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025 This option is primarily useful only for low level u-boot debugging on tablets, where normal UART0 is difficult to access and requires device disassembly and/or soldering. This patch now allows it to be selected from menuconfig. A dependency on SPL_FEL is added because u-boot does not support booting from NAND yet and also booting from SD card is impossible when a MicroSD breakout board is plugged into the SD slot. Additionally a compilation problem is fixed: common/spl/built-in.o: In function `spl_mmc_load_image': /tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init' scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sun8i: Add defconfig for Ippo_q8h v1.2Hans de Goede
We need separate defconfigs for the v5 and v1.2 versions of this board, as they use different DRAM parameters. Note they also use different dtb files, as the wifi is different too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun8i: Add dram initialization supportHans de Goede
Based on the register / dram_para headers from the Allwinner u-boot / linux sources + the init sequences from boot0. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: axp221: Disable dcdc4 on sun8i (A23)Hans de Goede
dcdc4 is not used on sun8i, disable it. While at it also add comments to the other fixed voltages to document what they are used for. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: axp221: Explicitly turn off unused voltagesHans de Goede
Explicitly turn off unused voltages, rather then leaving them as is. Likewise explictly enabled the dcdc convertors, rather then assuming they are already enabled at boot. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sunxi: axp221: Make dcdc1 voltage configurableHans de Goede
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to safe battery, but not on all, make it configurable so that we can use the same settings as the original firmware on all boards. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun6i: Add new board Merrii Hummingbird A31Chen-Yu Tsai
The Merrii Hummingbird A31 is a A31 based development board with 1G RAM, 8G NAND, AP6210 WiFi+BT, gigabit ethernet, USB OTG, 2 USB 2.0 ports connected to a USB hub chip, HDMI, VGA, TV and stereo in/out. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14sunxi: Add sunxi_get_sid helper functionHans de Goede
On sun6i the SID is stored in the pmic, rather then in the SoC itself, add a helper function to abstract this away. This makes our MAC address generation code also work on sun6i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun6i: Add new CSQ_CS908 boardHans de Goede
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND, rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG controller), ethernet, 3.5 mm jack with a/v out and hdmi out: http://www.geekbuying.com/item/CS908-Allwinner-A31S-Quad-Core-1-2GHz-Android-4-4-Mini-TV-Box-HDMI-HDD-Player-1G-8G-WIFI-Miracast---Black-333395.html Note it has no sdcard slot and therefore can only be fel booted. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14sun6i: Make dram clk and zq value Kconfig optionsHans de Goede
It turns out that there is a too large spread between boards to handle this with a default value, turn this into Kconfig options, and set the values the factory images are using for the Colombus and Mele_M9 boards. Note this changes the ZQ default when not overriden through defconfig from 120 to 123, as that is what most boards seem to actually use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-13arm: omap3: devkit8000: inherit from ti_omap3_common.hAnthoine Bourgeois
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
2015-01-13board: ti: am43xx: add support for AM43xx Industrial Development KitFelipe Balbi
AM43xx Industrial Development Kit is a new board based on AM437x line of SoCs. Targetted at Industrial Automation applications, it comes with EtherCAT, motor control and other goodies. Thanks to James Doublesin for all the help. Cc: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13Merge git://git.denx.de/u-boot-x86Tom Rini
2015-01-13board: ti: am43xx: take care of all OPPsFelipe Balbi
Make sure that all OPPs are checked on scale_vcores(). While at that also fix 600MHz VDD_MPU voltage according to AM437x Data Manual available at [1]. Table 5-3 on that document, lists all valid voltages per frequency. [1] http://www.ti.com/lit/ds/symlink/am4379.pdf Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13board: ti: am43xx: replace if else if else with a switchFelipe Balbi
A switch statement fits better in this case, specially considering we have a few extra frequencies to use. Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13arm: am437x: Correct PLL frequency for 25MHzJames Doublesin
The frequencies for 25MHz in dpll_per were out of spec for 25MHz, correct. Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-13arm: am437x: Enable hardware leveling for EMIFJames Doublesin
Switch to using hardware leveling for certain parameters on the EMIF rather than using precalculated values. Doing this also means we have a common place now between am437x and am335x for setting emif_sdram_ref_ctrl with a value for the correct delay length. Tested-by: Felipe Balbi <balbi@ti.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: James Doublesin <doublesin@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit (git 2.34.1) at 2025-01-04 12:47:15 +0000