| Age | Commit message (Collapse) | Author |
|---|
|
The OP-TEE binary to use is renamed to v2 as the v1 binary has been
deprecated and is no longer built by default.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Add entries for the newly created documentation files in reST
format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
- ABB SECU board
- Assorted minor fixes
|
|
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Now k3-image-gen[0] is the official repository for generating sysfw.itb
Update the same in AM65x and J721e README.
[0] https://git.ti.com/cgit/k3-image-gen/k3-image-gen/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Fix building errors if CONFIG_DM_VIDEO is enabled. This is the only
u-boot board that enables CONFIG_AM335X_LCD and from which I started
to develop the version of the frame buffer driver that supports the
driver model.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
Initialize both ESM and ESM_PMIC support if available for the board.
If support is not available for either, a warning is printed out.
ESM signals are only properly routed on PM2 version of the J721E SOM,
so only probe the drivers on this device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Update AM65x and J721e README files with instructions for flashing OSPI
images.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- convert stm32mp1 board documentation to rst format
|
|
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Just cosmetic change before real switch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes: 312f2c5b14fa ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The board has two push button connected to MIO pins
50 and 51, which have a pull-down resistor and are
connected to 1.8V when pressed.
These two pins are wrongly initialized with internal
pull-up enabled so they are reported as 1 all the time
with no change when pressed.
Disable the internal pull-up to fix the issue.
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
indicate power mode
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
|
|
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
On am571x-idk there can be following configurations based on Jumper J51
and LCD panel detected.
1) J51 removed (6port): 6 port Ethernet. Disable LCD panel.
2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD.
3) J51 placed (LCD) + Panel not detected/not supported.
Configuration 3 is considered invalid as we can't use display nor ICSS1
ethernet ports due to hardware muxing. Alert the user to fix the
configuration and prevent boot.
Alternative was to allow boot and limit to 4 port Ethernet with no display
but this involved introduction of another DTB for the kernel and was
considered not worth the hassle.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
|
|
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy uart pad and iomux code
Enable DM serial and mxc uart
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
|
|
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
|
|
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
commit 88718be30010 ("mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND")
moved CONFIG_NAND -> CONFIG_MTD_RAW_NAND. Adapt board code to this
change, as last merge did not respect the above commit.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage
on the XEA board (it also supplies TIVAs).
This code would enable TIVAs power supply early (also when board
uses the falcon boot).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The 'local-mac-address' property needs to be adjusted to the MAC address
value stored in U-Boot's 'ethaddr' env variable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
|
|
Minor spelling fix in README file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Assign Igor Opaniuk as a board maintainer.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add README with build steps for U-boot and TF-A for Verdin iMX8M Mini SoM.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add support for storing configuration for Verdin iMX8M Mini and
Nano SoMs in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add support for storing configuration for Apalis iMX8X SoM
in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
|
|
Add basic Presidio G3 engineering board support
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
|
|
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
|
|
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
