summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-04-14Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-13Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mipsTom Rini
- mt76xx: add USB support, small fixes - ath79: small fixes, add support for QCA9563 SoC and AP152 reference board - mscc: small fixes, add network support for JR2 and ServalT SoCs - bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs - MIPS: fix redundant relocation of initrd images
2019-04-12Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-bootTom Rini
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-04-12Merge git://git.denx.de/u-boot-marvellTom Rini
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
2019-04-12board: mscc: jr2: Update MSCC Jaguar2 boardsHoratiu Vultur
In Jaguar2 SoC family there are 3 different pcb. Each of this needs to configure the phys in different ways. Therefore implement the function board_phy_config and based on pcb configure them accordingly. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12mips: add initial support for qca956x referenced boardRosy Song
QCA9563 is CPU used on AP152 board : Clock speed : 750 MHz , Arch : Mips 74Kc, Eth : SGMII interface, MIMO config : 3 * 3 450M, 2 * USB 2.0, Signed-off-by: Rosy Song <rosysong@rosinson.com> Changes for v2: - coding style cleanup - remove ununsed flash chip in defconfig - enable automatic icache / dcache size in defconfig Changes for v3: - add detailed information for qca956x in commit message Changes for v4: - remove pre-configured network settings in ap152.h Changes for v5: - coding style cleanup
2019-04-12board: stm32mp1: Force pinctrl driver probe in board_init()Patrice Chotard
In order to insure that hog GPIOs are configured early during the boot process, force all pinctrl driver probing in board_init(). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12Board: stm32mp1: Add supply current boot informationPatrice Chotard
For DK1/DK2 boards, check if power supply provides enough current to allow the board to boot correctly. ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2 signals. The table below shows the behavior for different range of CC1 or CC2: range | power supply | red led | console message (Volts) | (Amps) | blinks | --------------|--------------|---------|----------------------------------- [2.10 - 1.23[ | 3 | NO | NO [1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected [0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected If detected current is < 3A, red led is kept ON after blinking. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12board: stm32mp1: Update README filePatrice Chotard
Update README with DK1 and DK2 boards related informations Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12stm32mp1: add syscfg initializationPatrick Delaunay
Initialize the system configuration for basic boot - update interconnect setting - disable pull-down for boot pin - enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI - activate I/O compensation Done by SSBL = TF-A for trusted boot Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: support forced boot modePatrick Delaunay
The boot mode can be forced by key press or by TAMP register, requested in kernel by syscon-reboot-mode tamp: tamp@5c00a000 { compatible = "simple-bus", "syscon", "simple-mfd"; reg = <0x5c00a000 0x400>; reboot-mode { compatible = "syscon-reboot-mode"; offset = <0x150>; /* reg20 */ mask = <0xff>; mode-normal = <0>; mode-fastboot = <0x1>; mode-recovery = <0x2>; mode-stm32cubeprogrammer = <0x3>; mode-ums_mmc0 = <0x10>; mode-ums_mmc1 = <0x11>; mode-ums_mmc2 = <0x12>; }; }; Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: update bootcmdPatrick Delaunay
Clearly separate bootcmd for stm32mp1 board (bootcmd_stm32mp) and preboot management. That solve issue for fastboot continue command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add runtime information in environmentPatrick Delaunay
Set board name with the first dts compatible found in DT code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG The result with DEVICE_TREE=stm32mp157c-ev1 is: STM32MP> env print board=stm32mp1 board_name=stm32mp157c-ev1 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: display board informationPatrick Delaunay
Implement checkboard() function to display - the boot chain used: basic or trusted - the board compatible in device tree - the board identifier and revision, saved in OTP59 for ST boards Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stm32mp1: add trusted boot with TF-APatrick Delaunay
Add support of trusted boot, using TF-A as first stage bootloader, The boot sequence is BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32 The TF-A monitor provides secure monitor with support of SMC - proprietary to manage secure devices (BSEC for example) - PSCI for power The same device tree is used for STMicroelectronics boards with basic boot and with trusted boot. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12MAINTAINERS: Change Jagan's email addressJagan Teki
Missed few mails from openedev, since most of the day I look at amarulasolutions mail so update the same. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12ARM: am3517_evm: Add spl_start_uboot for Falcon ModeAdam Ford
When booting the am3517-evm, the following message appears: SPL: Please implement spl_start_uboot() for your board SPL: Direct Linux boot not active! This patch implements spl_start_uboot to clear this message and allow device to know if it should boot U-Boot or kernel. Fixes: 1c6b6f383a41 ("ARM: am3517_evm: Enable Falcon Mode") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12board: ti: am335x: Remove non DM_ETH codeFaiz Abbas
With DM_ETH enabled in am335x devices, remove all the unused non-DM code. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: am335x: Add platdata for cpsw in SPLFaiz Abbas
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL is enabled. Use static platdata instead to save space. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: am65x: Enable fixing up msmc sram nodeLokesh Vutla
Create a ft_board_setup() api that gets called as part of DT fixup before jumping to kernel. In this ft_board_setup() call fdt_fixup_msmc_ram that update msmc sram node. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12arm: dra7: Allow NAND to be enabled on DRA71x EVM.Franklin S Cooper Jr
If SW 8 pins 0 and 1 indicate that NAND should be enabled then the pins pinmux must be reconfigured for NAND mode. Therefore, enable NAND by reconfiguring the pinmux. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12board: ti: dra71: Add pinmux settings for NAND on DRA71x EVMFranklin S Cooper Jr
By default VOUT3 occupies the pins required for NAND. Therefore, create a seperate entry that can be use to reconfigure these pins to work for NAND. On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is enabled or not. For NAND to be selected pin 0 should be on and pin 1 should be off. Any other combination will assume NAND shouldn't be enabled. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-04-12ARM: davinci: da850evm: Enable SPL_OF_CONTROL without PLATDATAAdam Ford
With the memory mapping giving us some more avialable RAM, this updates the da850-evm-u-boot.dtsi to include the serial port, SPI and Flash nodes along with some dependent nodes in the SPL dtb. This also removes the platform data initialization code for the serial port and SPI Flash. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12davinci: da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is fullAdam Ford
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit larger. This patch relocates BSS to SDRAM instead of SRAM which is similar to how ARMv7 boards (like OMAP2+) do it. This means two new variables are required: CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte before the location where U-Boot will load. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12am335x, guardian: Add support for the bosch guardian boardSjoerd Simons
Add support for the Bosch Guardian board. CPU : AM335X-GP rev 2.1 Model: Bosch AM335x Guardian I2C: ready DRAM: 256 MiB NAND: 512 MiB MMC: OMAP SD/MMC: 0 Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-12ARM: k2g: add a workaround to reset the phyMurali Karicheri
This patch adds a workaround to reset the phy one time during boot using GPIO0 pin 10 to make sure, the Phy latches the configuration from the input pins correctly. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12ARM: k2g-gp-evm: update to rgmii pinmux configurationMurali Karicheri
This patch updates pinmux configuration for K2G GP EVM based on data generated by the pinmux tool at https://dev.ti.com/pinmux/app.html#/default Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12ARM: k2g-ice: Add pinmux support for rgmii interfaceMurali Karicheri
This add pinmux configuration for rgmii interface so that network driver can be supported on K2G ICE boards. The pinmux configurations for this are generated using the pinmux tool at https://dev.ti.com/pinmux/app.html#/default As this required some BUFFER_CLASS definitions, same is re-used from the linux defnitions in include/dt-bindings/pinctrl/keystone.h Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-12arm: mvebu: Add DB-XC3-24G4XG boardChris Packham
The DB-XC3-24G4XG is a switch development board from Marvell. It can either use and external CPU card such as the db-88f6820-amc or the internal CPU that is integrated into the switch. Add support for running U-Boot on the internal CPU and enable the USB, SPI and NAND peripherals. For now this needs the bin_hdr from the Marvell U-Boot for this board. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12arm: mvebu: AXP: Enhance PCIe port capability configurationStefan Roese
This patch enables the PCIe port specific link capabilities configuration for Armada XP. The weak function board_sat_r_get() was used to return a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This is now changed with this patch to return a bit per PCIe port (4 bits in this case, bit 0 for PCIe port 0, etc). The theadorable board uses this new feature to configure PCIe port 0 as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards using this function are not changed in the configuration and still configure all ports as PCIe Gen2. This patch also removes the parameter "pex_mode" from board_serdes_cfg_get() as this parameter was not used in any of the implementations. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Phil Sutter <phil@nwl.cc>
2019-04-12arm: mvebu: clearfog: document eMMC installationBaruch Siach
Document build and install of U-Boot image on Clearfog with eMMC. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12arm: mvebu: theadorable: Add test for ctrl-c in PCIe PEX switch testStefan Roese
The check for the missing PEX switch can lead to an infinite loop, when the PCIe device is not found. It is helpful to enable the user to break out of this boot-loop, to enable booting to the prompt for test cases. This patch adds a 3 second delay in the error case before rebooting. The user can press Ctrl-C in this time to abort the boot-loop. This patch also calls bootcount_inc() before rebooting in the error case. This is needed to increment the bootcounter, since this function is called earlier than the main bootcounter increment. Otherwise the bootcounter will not be incremented in the error case at all. Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12arm: mvebu: x530: Enable watchdog in SPL and U-BootChris Packham
Enable the hardware watchdog to guard against system lock ups when running in the SPL or U-Boot. Stop the watchdog just before booting so that the OS can re-enable it if needed. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12watchdog: orion_wdt: take timeout value in msChris Packham
The generic wdt_start API expects to be called with the timeout in milliseconds. Update the orion_wdt driver to accept a timeout in milliseconds and use the clock rate specified in the dts to convert the timeout to an appropriate value for the timer reload register. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-11Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Various rmobile fixes
2019-04-10sun50i: a64: Add Oceanic 5205 5inMFD initial supportJagan Teki
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard designed to mount SoPine SOM. Key features: - Allwinner A64 Cortex-A53 - Mali-400MP2 GPU - AXP803 PMIC - 2GB DDR3 RAM - SD Slot - SPI-NOR flash - EMAC, RTL8211E - MCP2515 CAN - 4-lane, MIPI-DSI panel - Goodix 911 CTP - USB Host - 12V DC power supply Linux commit details about the sun50i-a64-oceanic-5205-5inmfd.dts sync: "arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support" (sha1: 00f7980a3bd53d12abc34f68146a8eed0e894248) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-09ARM: rmobile: rcar-common: Zap arch_preboot_os()Eugeniu Rosca
v2018.01 commit e23eb942ad103f ("ARM: rmobile: Stop using rcar-common/common.c on Gen3") removed board/renesas/rcar-common/common.c from the build chain with the reasoning that calling arch_preboot_os() is no longer needed. However, it left the arch_preboot_os() in place. Get rid of it. This is done in preparation of resurrecting rcar-common/common.c. NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h) are in direct relationship with the dropped arch_preboot_os() hook. The other headers (common.h, rmobile.h) are going to be needed by pretty much anything that is going to appear in the rcar common code. So, keep the two in place. Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
2019-04-09ARM: rmobile: Add R8A77965 M3NULCB supportMarek Vasut
Add defconfig and board specific adjustments for the R8A77965 M3N ULCB. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmelTom Rini
First set of u-boot-atmel features and fixes for 2019.07 cycle
2019-04-09arm: at91: Add gardena-gateway-at91sam supportStefan Roese
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage. This patch adds support for this board including SPL support. Therefore the AT91Boostrap is not needed on this platform any more. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-04-09board: pm9g45: Migrate to CONFIG_DMIlko Iliev
Migrate the following options to CONFIG_DM: CONFIG_DM_GPIO CONFIG_DM_MMC CONFIG_DM_ETH CONFIG_DM_SERIAL CONFIG_DM_USB Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2019-04-08Merge git://git.denx.de/u-boot-riscvTom Rini
- RISC-V arch support SMP. - Support Andestech's PLIC and PLMT. - qemu, fu54e, ae350 boards enable SMP by default. - Fix CONFIG_DEFAULT_DEVICE_TREE failure.
2019-04-08watchdog: Move watchdog_dev to data section (BSS may not be cleared)Stefan Roese
This patch moves all instances of static "watchdog_dev" declarations to the "data" section. This may be needed, as the BSS may not be cleared in the early U-Boot phase, where watchdog_reset() is already beeing called. This may result in incorrect pointer access, as the check to "!watchdog_dev" in watchdog_reset() may not be true and the function may continue to run. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100) Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2019-04-08riscv: ae350: enable SMPRick Chen
Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2019-04-08riscv: qemu: enable SMPLukas Auer
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-04-08riscv: fu540: enable SMPLukas Auer
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-07 12:00:12 +0000