| Age | Commit message (Collapse) | Author |
|---|
|
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.
SMP is not yet supported.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
These are currently dead codes. Until we have complete ACPI support,
we don't know if it works or not. Remove to avoid confusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
This Kconfig option name indicates it has something to do with cpu
socket, however it is actually not the case. Remove it and move
options inside it to NORTHBRIDGE_INTEL_IVYBRIDGE.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
There are some options which are never used, and also some options
which are selected by others but have never been a Kconfg option.
Clean these up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional.
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
Fix this by calling enable_fec_anatop_clock() earlier and also
by adding a 10ms reset delay as recommended in the AR8031 datasheet.
Suggested-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
After the conversion to SPL the defconfig was renamed, so adjust it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
|
|
Move driver to DM
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The SR1500 board is a CycloneV based board, similar to the EBV
SoCrates, equipped with the following devices:
- SPI NOR
- eMMC
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
|
|
For U-Boot's purposes, at present all we care about is ensuring there's
a model table entry.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
The RPi has two different schemes for encoding board revision values.
When adding RPi 2 support, I thought that the conflicting type field
values were to be interpreted based on bcm2835-vs-bcm2836. In fact, the
scheme bit determines the encoding. The RPi Zero uses the bcm2835 yet
uses the new encoding scheme. Fix the code to cater for this correctly.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
There are two numbering schemes for the RPi revision values; old and new
scheme. The values within each scheme overlap. Hence, it doesn't make
sense to have absolute/global names for the revision IDs. Get rid of the
names and just use the raw revision/type values to set up the array of
per-revision data.
This change makes most sense when coupled with the next change. However,
it's split out so that the mechanical cut/paste is separate from the
logic changes for easier review and problem bisection.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
Signed-off-by: Kamil Lulko <kamil.lulko@gmail.com>
|
|
|
|
The following patch changed the PFUZE100 swbst register bit definitions
and broke PMIC configuration on multiple boards, at least on the novena
and gw_ventana. This patch fixes it.
commit 8fa46350a4c7dca7710362f6c871098557b934ad
Author: Peng Fan <Peng.Fan@freescale.com>
Date: Fri Aug 7 16:43:45 2015 +0800
power: regulator: add pfuze100 support
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
|
|
This add some basic files required to allow the board to dispaly
serial message and can run command(mmc info etc)
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Moved board Kconfig fragment from previous patch into this one to fix
build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-changes: 8
- moved board Kconfig fragment from previous patch into this one
|
|
|
|
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
|
|
DPMACx to PHY mapping for SGMII is mentioned as QSGMII.
So fix typo in README for QSGMII rise card.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Change from ls2085aqds to ls2080aqds]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.
Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Print function name along with SerDes Protocol during SerDes Protocol
not supported error.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
|
|
|
|
In preparation of some new Liebherr boards to be added soon, a new
"liebherr" vendor directory gets created, and the "lwmon5" board
directory is moved into this new vendor directory.
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
|
|
Add board_usb_phy_mode function for detecting whether a port is
being used as host or client using a GPIO. On Colibri Vybrid we
provide GPIO 102 for this very same purpose.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
|
|
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add SPI NOR support:
=> sf probe
SF: Detected SST25VF032B with page size 256 Bytes, erase size 4 KiB, total 4 MiB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
|
|
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add defconfig files for the Orangepi Plus and Orangepi PC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This patch makes the 2nd DRAM bank available on Juno only and not on
other vexpress64 targets, eg. the FVP models.
The commit below added a 2nd bank of NOR flash for Juno, but also for
all vexpress64 targets:
commit 2d0cee1ca2b9d977fa3214896bb2e30cfec77059
Author: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Date: Mon Oct 19 11:08:31 2015 +0100
vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.
Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Unfortunately, I only fully tested on Juno R0, R1 and the FVP Foundation
model. Whilst FVP Base AEMV8 models run U-Boot OK, they fail to boot
the kernel.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Only compile in PCIe support if the board really uses it. Provide
a __weak stub for the init function if e.g. FVP is being built.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
On a Juno r1 the PCI controller init routine outputs the rather boring
ATR entry information.
Do this only with DEBUG defined to avoid cluttering the user's
terminal.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
|
|
This rewrite uses lately promoted eeprom_init(int) function to choose the
right I2C bus when writing data to the EEPROM.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
|
|
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This option is mentioned but does not do anything. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add support for the German keymap, taken from i8042.c. This can be selected
when the input library it initialised.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
