summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-10-11board: ti: am335x-ice: Configure the CDCE913 clock synthesizerTero Kristo
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am43xx-idk: Configure the CDCE913 clock synthesizerTero Kristo
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am57xx-idk: Configure the CDCE913 clock synthesizerTero Kristo
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: am65x: Print board name and version during bootLokesh Vutla
Print the board name and ver along with the DT Model. While at it print the ver for all the detected daughter cards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11am335x, guardian: update guardian boardMoses Christopher
- add BOARD_LATE_INIT function calls in board.c - add swi_status detection in board.c - mux: add guardian interfaces to single pinmux structure - am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11board: j721e: Add READMELokesh Vutla
Add README file explaining the build and boot procedure for J721E evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11board: ti: am65x: Add UART boot procedure in READMEAndreas Dannenberg
am65x ROM support booting over UART. And U-Boot built for am65x EVM supports UART boot as well. Add the UART boot procedure into the README also providing a corresponding example command sequence for execution on a host PC. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08ARM: imx6q_logic: Fix MMC2 bootingAdam Ford
With the reverting of a previous change to spl_boot_device, this board needs a new solution to determining if we're booting from MMC1 or MMC2. This patch creates board_boot_order function which overrides the standard, and returns not only MMC1, or MMC2, but also can fall back to NAND or the serial downloader should other boot options fail. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-10-08pico-imx7d: Remove dead code for dm_videoJoris Offouga
Since convert dm_video, unused code introduced, so remove this Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: fix splash logo drawingJoris Offouga
Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HABStefano Babic
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross architecture purposes. If Secure Boot is required for imx, this means to enable and use the HAB processor in the soc. Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-10-08ARM: imx6q_logic: Enable DM_SERIALAdam Ford
In order to call preloader_console_init from board_init_f when DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access to DM and device tree. This patch calls spl_early_init just before preloader_console_init() and enables DM_SERIAL and SPL_DM_SERIAL. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08ARM: imx6qlogic: Cleanup board_init_fAdam Ford
Per the workflow found in crt0.S, we don't need to clear BSS in board_init_f nor do we need to call board_init_r since that will be done for us from main when we return from board_init_f. This patch removes the unneeded function calls from board_init_f. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08mx6ulevk: Include SDP boot instructions in READMEBreno Matheus Lima
Add instructions on how to boot mx6ul_14x14_evk_defconfig target using the Serial Download Protocol. Add examples from uuu and imx_usb_loader tools. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx8mq: Update the ddrc QoS setting for B1 chipBai Ping
Update the ddrc Qos setting for B1 to align with B0's setting. Correct the initial clock for dram_pll. This setting will be overwrite before ddr phy training. Although there is no impact on the dram init, we still need to correct it to eliminate confusion. Signed-off-by: Bai Ping <ping.bai@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Tested-by: Robby Cai <robby.cai@nxp.com>
2019-10-08imx: initialize fec only when enabledParthiban Nallathambi
board early initialize fec ethernet controller pinmux only when FEC is enabled Signed-off-by: Parthiban Nallathambi <pn@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: remove board specific boot order from splParthiban Nallathambi
boot order was added to handle both SD and eMMC. But commit 14d319b1 introduced to handle both eMMC and SD globally. Signed-off-by: Parthiban Nallathambi <pn@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: pcl063: add nand boot supportParthiban Nallathambi
Booting from NAND needs nandbcb and nand boot device selection Signed-off-by: Parthiban Nallathambi <pn@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8: update READMEPeng Fan
After u-boot.cnt is padded to flash.bin automatically by script, no need to burn the image mannually, so drop the step. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: Add i.MX8MM EVK board support.Peng Fan
Add board and SoC dts Add ddr training code support SD/MMC/GPIO/PINCTRL/UART Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: mx6ul_14x14_evk: fix link issueAnatolij Gustschin
Since recent splash changes common code for splashscreen logo should be used instead of adding duplicated code under board directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations used old board specific logo code and do not link, fix them. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
2019-10-08mx28evk: README: Fix location for the generic mxs READMEFabio Estevam
doc/README.mxs no longer exists. It has been renamed doc/imx/common/mxs.txt, so fix the mx28evk README accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-10-08imx: wandboard: convert FEC support to DM_ETHAnatolij Gustschin
Remove CONFIG_DM_ETH conversion warning to avoid board removal. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08imx: Rewrite display5 get_board_id() function to use dm_gpio_* APILukasz Majewski
The get_board_id() function was using the old gpio_* compatibility layer to read HW and SW ID numbers encoded on the PCB board. After this change the new dm_gpio* API is used for this purpose. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08imx: Convert emergency pad of display5 to use dm_gpio* functionsLukasz Majewski
After this change the display5's emergency gpio use dm_gpio* functions instead of legacy ones (gpio*) to read its state. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: display5: Remove common.c file (after DM/DTS U-Boot proper conversion)Lukasz Majewski
The common.c file content can be safely moved to spl.c file after performing the DM/DTS conversion for the U-Boot proper. It contains the non DM/DTS setup code, which now is only used by SPL. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: display5: Remove UART initialization code after DM/DTS conversion ↵Lukasz Majewski
(non-console) This UART is not used in U-Boot, so there is no need to initialize it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: eth: Switch display5 board to use DM_ETHLukasz Majewski
After this commit the display5 device would use FEC driver supporting driver model (DM_ETH). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: mmc: Switch display5 board to use DM_MMC and BLK (USDHC)Lukasz Majewski
After this commit the display5 device would use eMMC driver supporting driver model (DM_MMC and BLK). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08imx: bk4: Print proper HW revision of VF610's BK4 boardLukasz Majewski
This code uses HW difference on the USB_RESET pin (added PULL UP resistor on the L333 rev) to distinguish between two BK4 HW revisions. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08pico-imx6: Add Falcon modeFabio Estevam
Add Falcon mode support, which allows the SPL to load and jump to the Linux kernel directly, without the need of loading U-Boot proper. CONFIG_SPL_OS_BOOT=y needs to be passed in the defconfig in order to use Falcon mode. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add splashscreen supportFabio Estevam
Add splashscreen support. Tested with the parallel FT5x06-WVGA panel. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add Ethernet supportFabio Estevam
Add Ethernet support. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6: Add initial supportFabio Estevam
Add the initial support for the pico-imx6 variants. DDR initialization is based on the TechNexion's U-Boot code. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08configs: pico-imx7d: Convert to DM_VIDEOJoris Offouga
This commit convert all pico-imx7d to DM_VIDEO Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08imx: fix missing MAINTAINERS pico boardsStefano Babic
Add missing files pico-nymph-imx7d_defconfig and c>onfigs/pico-dwarf-imx7d_defconfig Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com> CC: Fabio Estevam <festevam@gmail.com> CC: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Provide a way to escape the Falcon modeFabio Estevam
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able to escape from Falcon mode and boot to U-Boot proper. Add a mechanism that allows booting in U-Boot proper when the key 'c' is entered on console at boot time. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx7d: Add instructions for booting in Falcon modeFabio Estevam
Improve the README by adding instructions on how to boot using Falcon mode, which allows the SPL to load the kernel directly, without using U-Boot proper. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Provide a way to escape the Falcon modeFabio Estevam
When CONFIG_SPL_OS_BOOT is selected, it is still convenient to be able to escape from Falcon mode and boot to U-Boot proper. Add a mechanism that allows booting in U-Boot proper when the key 'c' is entered on console at boot time. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Update the Falcon mode instructionsFabio Estevam
Sync the Falcon mode instructions with the ones fro pico-imx7d. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08pico-imx6ul: Add LCD supportFabio Estevam
Add support for the VXT VL050-8048NT-C01 panel connected through the 24 bit parallel LCDIF interface. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08imx8qm_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Enable HUSH_PARSER in defconfig to make run netboot could work. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx8qxp_mek: switch to use container imagePeng Fan
Because FIT could not be used for AHAB secure boot on i.MX8, so switch to use container image that could let SPL verify ATF and U-Boot with AHAB. Note: The AHAB related code has not been added. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08imx: imx8qxp_mek: fix CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTORPeng Fan
The first stage of flash.bin is larger than 584 * 512, so when writting u-boot.itb, some data will be override. Enlarge the CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb bootPeng Fan
Since the SD3.0 kernel driver needs M4 image support, this causes problem for usb boot booting into kernel. To decouple the relationship, we modify the FDT file in u-boot to disable SD3.0. So the kernel won't depend on M4 image. Signed-off-by: Peng Fan <peng.fan@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-29 10:26:18 +0000