summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2017-03-17stm32f7: clk: remove usart1 clock enable from board initVikas Manocha
Before clock driver availability it was required to enable usart1 clock for serial init but now with clock driver is taking care of usart1 clock. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2017-03-17serial: stm32f7: add device tree supportVikas Manocha
This patch adds device tree support for stm32f7 serial driver & removes serial platform data structure. Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-17arm: imx6: tqma6: add support for TQMa6DL variantMarkus Niebel
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM Since The module will use the same devicetree, we patch the ram size in ft_board_setup. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17arm: imx6: tqma6: use CONFIG_TQM6x for SOM specific settingsMarkus Niebel
We have a Kconfig name for the module types. Let's Use it. Some feature selections and configurations are based on the module. Module selection selects the CPU type. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17i.MX6Q: isiot: Switch the mmc env based on devnoJagan Teki
Add board_mmc_get_env_dev Switch the mmc env based on the mmc devno, instead of separately defining a config item in include/configs using board_mmc_get_env_dev - devno 0: sd/esd - devno 1: mmc/emmc Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6Q: icorem6_rqs: Add mmc_late_initJagan Teki
Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6Q: icorem6_rqs: Add modeboot env via board_late_initJagan Teki
Add runtime, modeboot env which is setting mmcboot based on the bootdevice so-that conditional macros for MMC via CONFIG_BOOTCOMMAND should be avoided in config files. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17imx6: icorem6_rqs: Add eMMC boot supportJagan Teki
Boot from eMMC: -------------- U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21) Trying to boot from MMC2 U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: POR Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial switch to partitions #0, OK mmc1(part 0) is current device Net: No ethernet found. Hit any key to stop autoboot: 0 Booting from mmc ... switch to partitions #0, OK mmc1(part 0) is current device Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17mx6: tqma6: clear enet clk sel for mba6Markus Niebel
we have external ref clock from phy. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17imx6: tqma6: adjust ethernet phy reset delayMarkus Niebel
fix the reset delay which was to short Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17imx6: tqma6: disable spi CS unused in U-BootMarkus Niebel
Since the CS are not in use, do not map them. User of starterkit mainboard is free to use them otherwise. When using these pins later in the OS for instance as GPIO IRQ pin, they need to be input. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17imx6: tqma6: use lower driver stength for I2C pinsMarkus Niebel
The current driver stength is too high, leading to spec violations on the falling edge. Fix it with values from HW Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17imx6: tqma6: implement power_init_boardMarkus Niebel
PMIC implements proper I2C bus switching, implement power_init_board instead handling in board_late_init. Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2017-03-17imx6: icorem6_rqs: Update SPL board boot order for eMMCJagan Teki
SPL mmc device index is get based on the boot device, like - BOOT_DEVICE_MMC1 for mmc device 0 - BOOT_DEVICE_MMC2 for mmc device 1 Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC boot devices in i.MX, So u-boot is loading from mmc device 0 even "if the board booting from SD/eSD or MMC/eMMC" So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC the u-boot is loading from mmc device 1 and the board file need to take care if the board have different mmc device order intialization. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6UL: isiot: Switch the mmc env based on devnoJagan Teki
Add board_mmc_get_env_dev Switch the mmc env based on the mmc devno, instead of separately defining a config item in include/configs using board_mmc_get_env_dev - devno 0: sd/esd - devno 1: mmc/emmc Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6UL: isiot: Add mmc_late_initJagan Teki
Let the runtime code can set the mmcdev and mmcroot based on the devno using mmc_get_env_dev instead of defining separately in build-time configs using mmc_late_init func. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6UL: isiot: Add modeboot env via board_late_initJagan Teki
Add runtime, modeboot env which is setting mmcboot, or nandboot based on the bootdevice so-that conditional macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should be avoided in config files. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6UL: isiot: Add eMMC boot supportJagan Teki
Boot from eMMC: -------------- U-Boot SPL 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27) Trying to boot from MMC2 U-Boot 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27 +0100) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 36C Reset cause: POR Model: Engicam Is.IoT MX6UL eMMC Starterkit DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial switch to partitions #0, OK mmc1(part 0) is current device Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17imx6: isiotmx6ul: Update SPL board boot order for eMMCJagan Teki
SPL mmc device index is get based on the boot device, like - BOOT_DEVICE_MMC1 for mmc device 0 - BOOT_DEVICE_MMC2 for mmc device 1 Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC boot devices in i.MX, So u-boot is loading from mmc device 0 even "if the board booting from SD/eSD or MMC/eMMC" So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC the u-boot is loading from mmc device 1 and the board file need to take care if the board have different mmc device order intialization. Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17i.MX6: engicam: Include dts files under MAINTAINERSJagan Teki
dts files related to i.MX6 engicam boards are maintined under board, so include them under board/engicam/*/MAINTAINERS Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17imx6: isiotmx6ul: Add NAND supportJagan Teki
Add NAND support for Engicam Is.IoT MX6UL board. Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17arm: imx6ul: Add Engicam Is.IoT MX6UL Starter Kit initial supportJagan Teki
Boot from MMC: ------------- U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33) Trying to boot from MMC1 U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100) CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 33C Reset cause: POR Model: Engicam Is.IoT MX6UL Starterkit DRAM: 512 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 isiotmx6ul> Cc: Stefano Babic <sbabic@denx.de> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17imx: imx7ulp: add EVK board supportPeng Fan
Add EVK board support. Add the evk dts file. LOG: U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800) CPU: Freescale i.MX7ULP rev1.0 at 500 MHz Reset cause: POR Boot mode: Dual boot Model: NXP i.MX7ULP EVK DRAM: 1 GiB MMC: FSL_SDHC: 0 In: serial@402D0000 Out: serial@402D0000 Err: serial@402D0000 Net: Net Initialization Skipped No ethernet found. Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2017-03-16rockchip: rk3328: add evb-rk3328 supportKever Yang
evb-rk3328 is an evb from Rockchip based on rk3328 SoC: - 2 USB2.0 Host port; - 1 USB3.0 Host port; - 1 HDMI port; - 2 10/100M eth port; - 2GB ddr; - 16GB eMMC; - UART to USB debug port; Signed-off-by: William Zhang <william.zhang@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Simon Glass <sjg@chromium.org>
2017-03-16Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2017-03-14igep00x0: fixup FDT according to detected flash typeLadislav Michl
Leave only detected flash type enabled in FTD as otherwise GPMC CS is claimed (and never freed) by Linux, causing 'concurent' flash type not to be probed. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2017-03-14board: Add STMicroelectronics STiH410-B2260 supportPatrice Chotard
This is a 96Board compliant board based on STiH410 SoC: - 1GB DDR - On-Board USB combo WiFi/Bluetooth RTL8723BU with PCB soldered antenna - Ethernet 1000-BaseT - SATA - HDMI - 2 x USB2.0 type A - 1 x USB2.0 type micro-AB - SD card slot - High speed connector (SD/I2C/USB interfaces) - Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces) Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-14armv8: fsl-layerscape: Add vid support for LS2080AQDSPriyanka Jain
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Arpit Goel <arpit.goel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: fsl-lsch3: Update VID supportPriyanka Jain
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like LS2088A, LS2080A differs from existing logic. -VDD voltage array is different -Registers are different -VDD calculation logic is different Add new function adjust_vdd() for LSCH3 compliant SoCs Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Arpit Goel <arpit.goel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: layerscape: Update early MMU for DDR after initializationYork Sun
In early MMU table, DDR has to be mapped as device memory to avoid speculative access. After DDR is initialized, it needs to be updated to normal memory to allow code execution. To simplify the code, dram_init() is moved into a common file as a weak function. Signed-off-by: York Sun <york.sun@nxp.com>
2017-03-14armv8: layerscape: Rewrite memory reservationYork Sun
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved at the end of DDR. DDR is spit into two or three banks. This patch reverts commit aabd7ddb and simplifies the calculation of reserved memory, and moves the code into common SoC file. Secure memory is carved out first. DDR bank size is reduced. Reserved memory is then allocated on the top of available memory. U-Boot still has access to reserved memory as data transferring is needed. Device tree is fixed with reduced memory size to hide the reserved memory from OS. The same region is reserved for efi_loader. Signed-off-by: York Sun <york.sun@nxp.com>
2017-03-09TI: Migrate board/ti/common/Kconfig to implyTom Rini
The option that we had set in board/ti/common/Kconfig as default y are best done with imply under the appropriate main Kconfig option instead. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09am335x_evm: Switch to using imply keywordTom Rini
These particular SPL options are part of what the ROM provides, but for compatibility with how we have previously used them, move them to being implied by the board being selected. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigsTom Rini
In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-17da850: Add instructions to copy AIS image to an MMC cardahaslam@baylibre.com
The da850 soc's can boot from a external mmc card, but the AIS image should be written to the correct sector. Add instructions to copy the AIS image to a MMC card. Signed-off-by: Axel Haslam <ahaslam@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-17arm: am57xx: Set serial# variableSemen Protsenko
serial# variable is used to correctly display device ID in "fastboot devices". It also can be used further for displaying device ID in "adb devices" (should be passed as "androidboot.serialno" to kernel cmdline, via "bootargs" variable). Serial number generating algorithm is described at [1]. [1] http://lists.denx.de/pipermail/u-boot/2015-March/207462.html Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-02-12flash: complete CONFIG_SYS_NO_FLASH move with renamingMasahiro Yamada
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-11Merge git://git.denx.de/u-boot-samsungTom Rini
2017-02-10exynos: Drop large alignment for SDRAM parametersSimon Glass
We don't ever search for these so there is no need for a 4KB alignment. It just wastes space. Drop this and use the standard 4-byte alignment. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-02-09rockchip: rename miniarm to tinker boardEddie Cai
Miniarm is the internal project code. Now it is officially named Tinker board. So rename it. Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-09rockchip: Correct MAINTAINER entry for chromebook_minnieSimon Glass
This is wrong at present, so genboardscfg.py gives the following warnings: WARNING: no status info for 'chromebook_minnie' WARNING: no maintainers for 'chromebook_minnie' Fix it. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08Merge git://git.denx.de/u-boot-dmTom Rini
2017-02-08pcm052: fix DDR initialization sequenceAlbert ARIBAUD \(3ADEV\)
The sequence erroneously launched the DDR controller initialization before the pad muxing was done, causing DRAM size computation to hang. Configuring the pads first then launching DDR controller initialization prevents the DRAM hanging. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2017-02-08dm: core: Replace of_offset with accessorSimon Glass
At present devices use a simple integer offset to record the device tree node associated with the device. In preparation for supporting a live device tree, which uses a node pointer instead, refactor existing code to access this field through an inline function. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-07x86: qemu: Add a config for 64-bit U-BootBin Meng
Add a new board config which uses 64-bit U-Boot. Supported features are the same as the other 64-bit board (Google Chromebook Link). It is a start for us to test 64-bit U-Boot easily without the need to access a real hardware. Note CONFIG_SPL_ENV_SUPPORT is required for QEMU 64-bit as without this the SPL build fails at the end. This is just a workaround as CONFIG_SPL_ENV_SUPPORT is not needed at all. common/built-in.o:(.data.env_htab+0xc): undefined reference to 'env_flags_validate' lib/built-in.o: In function `hsearch_r': lib/hashtable.c:380: undefined reference to 'env_callback_init' lib/hashtable.c:382: undefined reference to 'env_flags_init' make[1]: *** [spl/u-boot-spl] Error 1 Except those SPL options required by 64-bit, compared to 32-bit config, the following options are different: - CONFIG_SYS_MALLOC_F_LEN has to be increased to 0x1000 for SPL. - CONFIG_DEBUG_UART has to be included due to the weird issue. See TODO comments in arch/x86/cpu/x86_64/cpu.c:arch_setup_gd(). Once this issue gets fixed, debug uart can be optional. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-07x86: qemu: Add a text base for 64-bit U-BootBin Meng
Set up the 64-bit U-Boot text base if building for that target. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-02-07x86: link: Add a config for 64-bit U-BootSimon Glass
Add a new board config which uses 64-bit U-Boot. This is not fully functional but is it a start. Missing features: - SDRAM sizing - Booting linux - EFI support - SCSI device init (and others) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-07x86: link: Add a text base for 64-bit U-BootSimon Glass
Set up the 64-bit U-Boot text base if building for that target. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-02-03Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/ls1046aqds_defconfig configs/ls1046aqds_nand_defconfig configs/ls1046aqds_qspi_defconfig configs/ls1046aqds_sdcard_ifc_defconfig configs/ls1046aqds_sdcard_qspi_defconfig configs/ls1046ardb_emmc_defconfig configs/ls1046ardb_qspi_defconfig configs/ls1046ardb_sdcard_defconfig
2017-02-03armv8: ls1012a: Add support of PPAPrabhakar Kushwaha
The PPA implements PSCI which requires for power managment. Added support of PPA for LS1012AQDS, LS1012ARDB and LS1012AFRDM. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-08 04:39:04 +0000