summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2016-07-19ARM: board: cm_fx6: fixup mtd partitions in the fdtChristopher Spinrath
The cm-fx6 module has an on-board st,m25p compatible spi flash chip used for U-Boot (binary & environment). Overwrite the partitions in the device tree by the partition table provided in the mtdparts environment variable, if it is set. This allows to specify a kernel independent partitioning in the environment and provides a convient way for the user to adapt the partition table. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-07-19pico-imx6ul: Add PMIC supportVanessa Maegima
Add PMIC support. Tested by command "pmic PFUZE3000 dump". Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12usbarmory: Add board_run_command() functionAndrej Rosano
Define a default board_run_command() function. This function contains the commands needed to boot the board when CLI is disabled (CONFIG_CMDLINE=n). Signed-off-by: Andrej Rosano <andrej@inversepath.com>
2016-07-12pico-imx6ul: Add USB Host supportVanessa Maegima
Add USB host support. Tested by connecting a USB pen drive: => usb start starting USB... USB0: Port not available. USB1: USB EHCI 1.00 scanning bus 1 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12pico-imx6ul: Add a README fileVanessa Maegima
Add a README file to help users to install U-boot binary into the eMMC. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12pico-imx6ul: Add Ethernet supportDiego Dorta
Pico-imx6ul has a KSZ8081 Ethernet PHY. Add support for it. Signed-off-by: Diego Dorta <diego.dorta@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-07-12mx6sxsabresd: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
2016-07-12mx6sxsabreauto: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12mx6slevk: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12wandboard: enable SATA with imx6qGilles Chanteperdrix
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
2016-07-12mx6qsabreauto: Avoid hardcoded RAM sizeVanessa Maegima
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option, we should better use imx_ddr_size() function, which automatically determines the RAM size. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12mx6: Add Phytec PCM058 i.MX6 QuadStefano Babic
Add Phytec-i.MX6 SOM with NAND Support: - 1GB RAM - Ethernet - SPI-NOR Flash - NAND (1024 MB) - external SD - UART Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-12mx6: add support for el6x boardStefano Babic
Custom Board based on MX6 Dual, 1GB RAM and eMMC. There are two variants of the board with and without PCIe (ZC5202 and ZC5601). Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-07-12ARM: board: cm-fx6: fix mmc for old revisions of utiliteChristopher Spinrath
Old revisions of Utilite (based on cm-fx6) do not have a dedicated card detect pin. But the card is removable by the user and card detection can be realized with polling (e.g. supported by Linux). Add the broken-cd property to the mmc device tree instead of the non-removable property to make card detection possible if polling is supported. Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2016-07-11doc: ARMv8: add README.pine64Andre Przywara
Since we lack information about the DRAM initialization for the Allwinner A64 SoC, booting any A64 based board like the Pine64 is a bit involved at the moment. Add a README file to explain the process. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Move to board/sunxi/ from doc/] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-07-02sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)Quentin Schulz
The Parrot Board is an evaluation board with an Allwinner R16 (assumed to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2 controllable buttons, an LVDS port with separated backlight and capacitive touch panel ports, an audio/microphone jack, a camera CSI port, 2 sets of 22 GPIOs and an accelerometer. The DTS file is identical to the one submitted to the upstream kernel. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-02sunxi: spl: Fix DRAM info printingHans de Goede
The switch to simple_printf was causing the SPL dram info to show as: DRAM: u MiB This fixes this by switching from %lu to %d for printing the DRAM size. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-01ti_omap5_common: Find right dtb file for DRA72-RevC EvmLokesh Vutla
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-07-01ARM: AM437x: Align HS device variant defconfig filenameAndreas Dannenberg
Align the name of the defconfig file for high-security (HS) device variants from the AM43xx family of SoCs with the corresponding name used for the general purpose devices. This allows for easier cross-association of those files and also provides room to grow from an HS device part number perspective. Furthermore, update and cleanup associated MAINTAINERS file. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Madan Srinivas <madans@ti.com>
2016-06-28Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-06-28armv8: ls1043aqds: use configurable clockQianyu Gong
Get the clocks from FPGA through I2C, if IFC is disabled. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-27Kconfig: make NOR_BOOT a common optionPeng Fan
Not only am335x supports booting from NOR, i.MX6 SoCs also supports booting from NOR. Make NOR_BOOT a common option to let different SoCs share it. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Christophe Ricard <christophe-h.ricard@st.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Francois Retief <fgretief@spaceteq.co.za> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-06-27maintainers: new email addressSteve Rae
Update the email address for the boards that I maintain. Signed-off-by: Steve Rae <steve.rae@raedomain.com>
2016-06-26arm: at91: taurus/axm: add DM and DTS supportHeiko Schocher
add DM and DTS support for the at91 based siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26arm: at91: smartweb: add DM and DTS supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebased on current ToT] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26corvus DTS / DM supportHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [rebase on current ToT, don't delete gurnard DTB creation] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-24board/BuR: rename kwb board to brxre1Hannes Schmelzer
Rename B&R kwb board to brxre1 Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24board/BuR: rename tseries board to brppt1Hannes Schmelzer
Rename B&R tseries board to brppt1 Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-24hush: complete renaming CONFIG_SYS_HUSH_PARSER to CONFIG_HUSH_PARSERMasahiro Yamada
There is no more define of CONFIG_SYS_HUSH_PARSER. Rename some remaining references and drop the backward compatible Kconfig entry. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-24board: amlogic: Rename folder for Amlogic boardsCarlo Caione
s/hardkernel/amlogic/ to have a single place for all the amlogic-based boards. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Carlo Caione <carlo@endlessm.com> Acked-by: Beniamino Galvani <b.galvani@gmail.com>
2016-06-24armv8: ls1043aqds: fix to get boot device info from FPGAQianyu Gong
The LBMAP switches on the board will tell which boot device is used. Only QSPI boot is supported if the boot device is IFCCard. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-20sunxi: Revert "sunxi: make SoC variant choice mandatory"Hans de Goede
This reverts commit 1a5f0de08e86("sunxi: make SoC variant choice mandatory"). With the optional marking in the Kconfig "make savedefconfig" will drop CONFIG_MACH_SUN4I=y from all the A10 boards, making it hard to see at a glance which family of sunxi chips the defconfig is for. This commit therefore restores the optional, and restores CONFIG_MACH_SUN4I=y to all defconfig's which had it dropped because of this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20sunxi: Add defconfig and dts file for inet86dz boardHans de Goede
The inet86dz board is a board used in 7" tablets from various oems. These tablets are a23 based 7" tablets featuring a 1024x600 LCD, 512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file this commit adds is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tabletHans de Goede
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0 PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680 touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector which doubles as charging port. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-19clk: convert API to match reset/mailbox styleStephen Warren
The following changes are made to the clock API: * The concept of "clocks" and "peripheral clocks" are unified; each clock provider now implements a single set of clocks. This provides a simpler conceptual interface to clients, and better aligns with device tree clock bindings. * Clocks are now identified with a single "struct clk", rather than requiring clients to store the clock provider device and clock identity values separately. For simple clock consumers, this isolates clients from internal details of the clock API. * clk.h is split so it only contains the client/consumer API, whereas clk-uclass.h contains the provider API. This aligns with the recently added reset and mailbox APIs. * clk_ops .of_xlate(), .request(), and .free() are added so providers can customize these operations if needed. This also aligns with the recently added reset and mailbox APIs. * clk_disable() is added. * All users of the current clock APIs are updated. * Sandbox clock tests are updated to exercise clock lookup via DT, and clock enable/disable. * rkclk_get_clk() is removed and replaced with standard APIs. Buildman shows no clock-related errors for any board for which buildman can download a toolchain. test/py passes for sandbox (which invokes the dm clk test amongst others). Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-18Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-06-18warp7: Add README fileMarco Franchi
Add a README file for helping users to install U-Boot into the eMMC. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18warp7: Fix watchdog resetMarco Franchi
The latest version of warp7 board provides the connection of the WDOG1_B pin to the PMIC. Program the watchdog to enable the WDOG1_B output which causes a POR reset. Based on the imx7dsabresd code. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx: mx6ulevk: change QSPI PAD DSE to 120ohmPeng Fan
The current pad DSE for QSPI is 60ohm. This setting cause too strong drive to clock and data signals. Need to change the DSE to 120ohm for better signal quality. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix LCD_nPWREN settingPeng Fan
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3. If LCD_nPWREN is high, output is 2.4V which is not correct. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix 74LV OE usagePeng Fan
Fix 74LV OE gpio index. gpio index is wrong, so gpio output will not have effect, since we use wrong GPIO5_IO18, but not correct GPIO5_IO8. And at the end of the initialization of 74lv init, should keep OE voltage level at LOW to make 74lv output the correct voltage. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx7dsabresd: Fix LCD_PWR_EN output settingYe Li
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3 is actually 1.2V. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx6sabresd: Allow LVDS backlight to be functional after a kernel rebootMarco Franchi
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand in the kernel. This problem occurs because the kernel uses this pin in PWM mode and U-Boot does not configure the backlight pin as GPIO functionality. So fix the problem by explicitly configuring the backlight pin as GPIO in U-Boot. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-06-17Orphan dbau1x00 boardsThomas Lange
I no longer have access to such a board Signed-off-by: Thomas Lange <thomas@corelatus.se>
2016-06-13usb: xhci: fsl: Add workaround for USB erratum A008751Sriram Dash
This patch is doing the following: 1. Implementing the errata for LS2080. 2. Adding fixup for fdt for LS2080. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13board: am437x-hs: spl: Select right dtb from fitLokesh Vutla
Select a right dtb from FIT for am437x-hs platform. Reported-by: Madan Srinivas <madans@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13ARM: dts: AM572x-IDK Initial SupportSchuyler Patton
Add initial DTS support for AM572-IDK evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Schuyler Patton <spatton@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit (git 2.34.1) at 2024-12-29 06:30:57 +0000