| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
|
|
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
|
|
This patch sets up pinmux, enables fclk, and
defines CONFIG_I2C_MULTI_BUS
Signed-off-by: Steve Sakoman <steve@sakoman.com>
|
|
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
|
|
static
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
|
|
Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x08222204, where as currently it
configured to 0x00100084 in U-Boot. This issue was found out when
support for NAND SPL is added in U-Boot. Without this patch U-Boot
does not come up with SPL.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
|
|
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
|
|
This patch adds support for MMC/SD on DA850/OMAP-L138.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
|
|
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h
PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
|
|
Detect hot-water-button to start a differnt image.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
|
|
Fix the comment to reflect the actual function call time.
Change the printf message to look nicer in the context it might be printed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Parameters used for configuring certain SoC peripherals are parsed
from the cfg file and appended as part of the ais image's header. The
u-boot-spl.ais generated is flashed separately to the nand, so do not
delete the file after generation of u-boot.ais.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
|
|
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Remove old o2dnt board without OF support. New support for this board
is added by the previous patch, O2I configuration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Add common code for o2dnt and o2dnt2 based boards and add different
board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and
O3DNT boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Instead of manipulating gpio registers directly, use the calls
from the gpio library.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
* rename board directory to eb_cpu5282
* rename EB+MCF-EV123_.*config to eb_cpu5282_.*config
* add Maintainer for EB+CPU5282 board
* rename prompt
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
|
|
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.
For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.
Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.
Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead. Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.
Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.
Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
|
|
* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable I2C
I2C: Add support for Multi channel
I2C: Modify the I2C driver for EXYNOS5
I2C: Move struct s3c24x0_i2c to a common place.
EXYNOS: PINMUX: Add pinmux support for I2C
EXYNOS5: define EXYNOS5_I2C_SPACING
EXYNOS: Add I2C base address.
EXYNOS: CLK: Add i2c clock
mx6qsabrelite: add i2c multi-bus support
imx-common: add i2c.c for bus recovery support
i.mx53: add definition for I2C3_BASE_ADDR
i.mx: iomux-v3.c: move to imx-common directory
i.mx: iomux-v3.h: move to imx-common include directory
iomux-v3: remove include of mx6x_pins.h
mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
mxc_i2c: add bus recovery support
mxc_i2c: prep work for multiple busses support
mxc_i2c: add i2c_regs argument to i2c_imx_stop
mxc_i2c: add retries
mxc_i2c: check for arbitration lost
mxc_i2c: change slave addr if conflicts with destination.
mxc_i2c: don't disable controller after every transaction
mxc_i2c: place i2c_reset code inline
mxc_i2c: place imx_start code inline
mxc_i2c: remove redundant read
mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
mxc_i2c.c: code i2c_probe as a 0 length i2c_write
mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
mxc_i2c: create i2c_init_transfer
mxc_i2c: clear i2sr before waiting for bit
mxc_i2c: create tx_byte function
mxc_i2c: remove ifdef of CONFIG_HARD_I2C
mxc_i2c: fix i2c_imx_stop
i2c: deblock i2c bus also if accessed before realocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Wire up SPI driver
spi: microblaze: Adds driver for Xilinx SPI controller
microblaze: intc: Clear interrupt code
microblaze: Call serial multi initialization
microblaze: Move __udelay implementation
microblaze: Remove extern from board.c
microblaze: Wire up dts configuration
fdt: Add board specific dts inclusion
microblaze: Move individual board linker scripts to common script in cpu tree.
microblaze: Add gpio.h
microblaze: Add missing undefs for UBI and UBIFS
microblaze: Expand and correct configuration comments
microblaze: Enable ubi support
microblaze: Avoid compile error on systems without cfi flash
microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This code will also be used before reallocation and during this time we
are not allowed to do these printings.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
This enables I2C support on smdk5250.
Pinmux setting moved to board file to avoid repeated setting of
gpio lines.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This includes bus recovery support.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Jason Liu <r64343@freescale.com>
|
|
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This fixes:
cmd_bc3450.c:55:0: warning: "CONFIG_SYS_CPU" redefined [enabled by default]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
|
|
In commit 1a89a217f5c5ab3645c80c1247e8911a8b5ad491 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured. This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.
Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.
(Reworded by Tom Rini to be more precise about what the problem was)
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
|
|
Add I2C support.
Tested by placing a 24LC16 EEPROM into the U50 slot which comes empty from factory.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
- enable OF control and embedded OF
- set default device tree file name to 'microblaze'
- add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
- add an empty but processable dts for microblaze-generic
Signed-off-by: Stephan Linz <linz@li-pro.net>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
When Trimslice is booted from serial flash, the boot ROM does this, so
U-Boot doesn't need to. However, booting from the SD slot for recovery
purposes, the boot ROM does not set up the pinmux for serial flash. Add
code to U-Boot to set this up, so that an SD-based recovery U-Boot image
can upgrade the U-Boot in serial flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Boards can override this to set up the pinmux correctly to access serial
flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
The Tamonten Evaluation Carrier is an evaluation board for the Tamonten
processor board. More information is available here:
http://www.avionic-design.de/en/products/nvidia-tegra-tamonten-system-en/nvidia-tegra-tamonten-evboard-en.html
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
GPIO PI6 can be used to obtain the write-protect status of an SD card
inserted into the SD slot.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Device tree support is required for working USB host support, which in
turn enables ethernet support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
this is for a prototyping board
vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
|
