| Age | Commit message (Collapse) | Author |
|---|
|
The Low Level init functions start the UART, so it doesn't need
to happen during board_init. This patch removes it from
board_init.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The reset line going to the ethernet controller is controlled
by a global reset controlling multiple peripherals. There
is no need to manually invoke the reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Add initial defconfig support for J721e that runs on A72.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add initial defconfig support for J721e that runs on R5.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Add MAINTAINERS file]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add board specific initialization for j721e evm
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
|
|
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
|
|
make_fit_atf.py no longer requires pyelftools, and nothing else in the
rockchip build requires it either, so remove references to installing it
from the documentation.
Signed-off-by: Chris Webb <chris@arachsys.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
|
|
Prefer to use dts config instead, remove all board_boot_order()
for rk3288 boards.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
This patch enables SiFive SPI and MMC SPI drivers for the
SiFive Unleashed board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This patch extends SiFive FU540 board support to setup ethaddr
env variable based on board serialnum read from OTP.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The GEMGXL clock driver is now directly part of Cadence MACB
ethernet driver in upstream Linux kernel. There is no separate
GEMGXL clock driver in upstream Linux kernel hence we drop
GEMGXL clock driver from U-Boot as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The mail format should have '<>', or else the patman won't
recognize it correctley.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
|
|
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
|
|
libvirt v.5.3.0 with QEMU 4.0.0 or above uses PCI automatically and
thus devices (network, storage, etc) are connected via PCI.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The AM654x EVM based on the TI K3 family of SoCs has an updated board
detection EEPROM structure that contains a TLV record of dedicated MAC
addresses rather than a range of MAC addresses as it was used on earlier
platforms such as DRA7. Add a basic function that allows us setting up
Ethernet MAC addresses into the U-Boot environment based on the MAC
address record contained in the common TI EEPROM structure.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The AM654x EVM based on the TI K3 family of SoCs have an updated board
detection EEPROM structure, now comprising variable-sized TLV-type
records, containing a superset of what is already being provided on
earlier platforms such as DRA7. Add basic support for parsing the new
data structures contained on the base board into the common TI EEPROM
structure while also providing infrastructure that can be used later on
to parse data from additional EEPROMs such as the ones that are used on
daughtercards for this platform.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add instructions for flashing boot images to the eMMC with a
layout of the address where each image needs to be flashed.
Also add instructions to flash filesystem partition in user
partition and boot kernel from the rootfs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
|
|
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
|
|
With a recent update to the pinctrl-single driver and the fact
that the da850evm has both DM and OF_CONTROL working in both SPL
and U-Boot, some of the manual pinmuxing can be setup to only
be activated when either the driver doesn't have DM for it, or
when CONFIG_PINMUX isn't available (only during SPL). If the
code ever shrinks enough to support PINCTRL in SPL, a lot of this
can go away. This also remove some manual pinmuxing not needed
by SPL to give SPL a little more breathing room.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.
CPU : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
eth0: ethernet@4a100000
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART
- USB (host)
Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")
Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
|
|
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
|
|
This addresses the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
As USB support for older OMAP3 SoC's improves, OMAP3 EVM can be
readily adapted. There is some additional 'gpio-hog' support
needed to fully setup USB in a similar manner to Linux.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
|
|
Convert the board to support the USB and video driver model and remove
the unnecessary code.
|
|
Convert the board to support the USB and video driver model and remove
the unnecessary code.
|
|
This fixes the following error message:
U-Boot 2019.07-rc4-00103-g5eea874b5e (Jun 25 2019 - 15:09:31 +0200)
DRAM: 8 MiB
gpio@40021800: dir_output: error: gpio GPIOG14 not reserved
gpio@40021800: dir_output: error: gpio GPIOG13 not reserved
gpio@40021800: set_value: error: gpio GPIOG14 not reserved
Flash: 2 MiB
....
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This patch solves the following warnings:
warning: no previous prototype for 'board_quiesce_devices' [-Wmissing-prototypes]
void board_quiesce_devices(void)
^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Update kernel MTD partition in device tree with U-Boot information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Remove post.h include as it is used in spl.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add latest information and correct some information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Allow to update board identification in OTP 59.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
U-Boot activates regulators by reading the "regulator-boot-on"
property in DT; it is requested by M4 early Boot feature.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Move 2 ENV configuration flags in board Kconfig
- CONFIG_ENV_SECT_SIZE
- CONFIG_ENV_OFFSET
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
|
|
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The corresponding configurations are selected in the common Kconfig file.
This is easier than changing every affected board default configuration
file. The default configuration for the PORTL2 board, however, still needs
some modifications to correctly use the driver model.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
As the SPI NOR and NAND devices share the same hardware pins, the MPP
configuration has to be changed when claiming/releasing the bus. The
current configuration is saved when claiming and restored when releasing.
Furthermore, a general-purpose output is used to switch the chip-select
signal. This is now also implemented for the DM part of the kirkwood_spi
driver.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Rescue mode bootcmd currently only appends the "omniarescue" parameter
to the bootargs variable. We do not want the user to be able to change
rescue mode bootargs. Therefore change this so that bootcmd sets the
bootargs variable in an absolute way (adding console device information
and the omniarescue paramterer).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
We always want to enumerate PCIe devices, because withouth this they
won't work in Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The board code reads MAC addresses from the ATSHA204A cryptochip.
For compatibility reasons the ethernet adapters on this SOC are not
enumerated in register address order. But when Omnia was first
manufactured this was done differently.
Change setting of MAC addresses to conform to the description on the
stickers sticked on actual Omnias.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
