summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2012-11-26powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL bootScott Wood
This allows DDR configuration to be deferred to the final U-Boot image, which is able to make use of SPD data. The SPL itself cannot use SPD due to code size constraints. It previously used fixed register values for DDR configuration, and those values did not work on the p2020rdb-pca board I tested with. It's possible that different revisions of the board require different settings. Using SPD eliminates that problem. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx/p1_p2_rdb_pc: clean up memory mapScott Wood
- Sort by address, and fix column alignment - Don't label things as localbus that aren't. Instead, put chipselect info at the end of the description for localbus windows. Note that NAND/NOR have their chipselects swapped when booting from NAND, and CS2 can be either PMC or VSC7385 depending on hwconfig. - Shrink NAND to the 32K that's actually mapped in the localbus - Assign an address and size to L2 SRAM. Remove the similarly named but unintelligible "L2 SDRAM(REV.)". - Remove the untrue comment about L1 stack being mapped with TLB0. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-26powerpc/mpc85xx/p1_p2_rdb_pc: new SPL supportScott Wood
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK. Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Andy Fleming <afleming@freescale.com>
2012-11-25Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2012-11-20omap3_beagle: add musb-new initIlya Yanok
Add initialization for new MUSB framework. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20am3517_evm: switch to musb-newIlya Yanok
Use new musb framework instead of the old one on AM3517_EVM. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20am335x_evm: enable both musb gadget and hostIlya Yanok
Enable musb gadget in Ethernet mode on port 0 and musb host on port1. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-19Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
2012-11-19ARM: tegra: enable 8-bit SD slots in board filesStephen Warren
Harmony contains an SD slot with all 8 bits routed. This allows plugging in an eMMC-chip-in-SD-form-factor. Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits hooked up. Now that the U-Boot eMMC code fully supports 8-bit operation, initialize those ports as 8-bit instead of 4-bit to improve performance. Whistler was already registering its ports as 8-bit. TrimSlice doesn't have any 8-bit ports. I don't have any Avionic Design boards nor the Colibri board to test with. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19ARM: tegra: TrimSlice: add support for USB1 portStephen Warren
TrimSlice's USB1 port has two purposes; it either acts as a device port hosting Tegra's USB recovery protocol, or acts as a host port connected to the internal USB->SATA bridge chip, which may in turn be connected to an SSD or HDD. Add the appropriate device tree and board configuration options to enable this port as a host port, and route the port to the SATA bridge using the VBUS GPIO. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19tegra: fdt: Add LCD definitions for SeaboardSimon Glass
The Seaboard has a 1366x768 16bpp LCD. The backlight is controlled by one of the PWMs. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19tegra: Add LCD support to Nvidia boardsSimon Glass
Add calls to the LCD driver from Nvidia board code. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19tegra: Add support for PWMSimon Glass
The pulse width/frequency modulation peripheral supports generating a repeating pulse. It is useful for controlling LCD brightness. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-16mx35pdk: Add support for OTGBenoît Thébaudeau
Add support for the OTG port on the mx35pdk Personality board. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Stefano Babic <sbabic@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de>
2012-11-15EXYNOS5: Enable SPI booting.Rajeshwari Shinde
This patch enables SPI Booting for EXYNOS5 Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15EXYNOS5: Enable SPIHatim RV
This patch enables SPI driver for EXYNOS5. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Hatim Ali <hatim.rv@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15exynos4: universal_C210: add display supportPiotr Wilczek
This patch add support for display on Universal C210 board. Width of displyed logo must be not bigger than 480 pixel and is limited by width of the screen. Tizen logo size is 520x120 pixels and should be resized. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15exynos4: universal_C210: use software SPIPiotr Wilczek
This patch use software spi on Samsung Universal C210 board. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15SMDK5250: Config: Enable MAX77686 pmic chipRajeshwari Shinde
This patch enables MAX77686 pmic chip for SMDK5250. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15arm: trats: Power down core 1Piotr Wilczek
This patch turns power down for unused core 1 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15arm:exynos4:universal: Eliminated low level initPiotr Wilczek
Low level initialisation is done by another bootloader Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15arm:exynos4:universal: Use pinmux for mmc configurationPiotr Wilczek
This patch use the pinmux for mmc configuration for Universal C210 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15arm:exynos4:trats: Use pinmux for mmc configurationPiotr Wilczek
This patch use the pinmux for mmc configuration for Trats Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-15arm:exynos4:trats: Fix SDRAM sizePiotr Wilczek
Full 1GiB is visible Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14mx53loco: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan
The inclusion of LCD patch into mx53loco breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14mx51evk: Fix build error when CONFIG_VIDEO is disabledVikram Narayanan
The inclusion of LCD patch into mx51evk breaks the build when CONFIG_VIDEO is disabled. Fix this by splitting the video related stuff to a new file. Also rename the function lcd_iomux to setup_iomux_lcd to make the namings aligned with the other iomux functions. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14M68K: eb_cpu5282: general update and enhanced board supportJens Scharsig (BuS Elektronik)
- update clock settings for higher perfomance - change standard baud rate to 115200 - fix flash base address - remove unused defines - add I2C support - switch form board dependent flash to cfi - remove board dependent flash code - use sdram bank 0 instead of bank 1 on boot - enable on board frame buffer instead external - remove fake mac address form config - add watchdog support - add status led support Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> [agust: fixed small style issues and build warning] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-14arm:universal_c210:pmic: Adjust C210 Universal target platform board to new ↵Łukasz Majewski
PMIC framework Move pmic_init() function call from board_init() to power_init_board() to work with new PMIC/POWER framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:goni:pmic: Adjust GONI target platform board to new PMIC frameworkŁukasz Majewski
Move pmic_init() function call from board_init() to power_init_board() to work with new PMIC/POWER framework. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14power:pmic: Rename CONFIG_PMIC* defines to CONFIG_POWERŁukasz Majewski
Rename all CONFIG_PMIC* defines to CONFIG_POWER* Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-14arm:trats:pmic: Support for charging battery at Samsung's TRATS boardŁukasz Majewski
The battery connected to Samsung's Trats development board is now charged when voltage drops below threshold. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Power consumption reduction state for Samsung's TRATS boardŁukasz Majewski
When charging battery is necessary, the development board needs to be turned into low power mode for better efficiency. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Enable battery support at Samsung's TRATS boardŁukasz Majewski
Support for TRATS battery has been added. It is treated as a "normal" power related device and thereof controlled by pmic/power subsystem. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Enable fuel-gauge (MAX17042) at Samsung's TRATS boardŁukasz Majewski
FG IC built into the MAX8997 device (compliant to MAX17042) is enabled at TRATS. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Enable MUIC (MAX8997) at Samsung's TRATS boardŁukasz Majewski
MUIC IC built into the MAX8997 device is enabled at TRATS. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14arm:trats:pmic: Default PMIC(MAX8997) initialization for Samsung's TRATS boardŁukasz Majewski
Default PMIC (MAX8997) initialization for Samsung's TRATS development board. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14pmic: Enable power_board_init() support at TRATSŁukasz Majewski
Enable support for power_board_init() method at TRATS board. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-11-14pmic: Extend PMIC framework to support multiple instances of PMIC devicesŁukasz Majewski
The PMIC framework has been extended to support multiple instances of the variety of devices responsible for power management. This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB Interface Circuit). Power related includes have been moved to ./include/power directory. This is a first of a series of patches - in the future "pmic" will be replaced with "power". Two important issues: 1. The PMIC needs to be initialized just after malloc is configured 2. It uses list to hold information about available PMIC devices Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2012-11-10Merge git://git.denx.de/u-bootStefano Babic
2012-11-05Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2012-11-04powerpc/mpc83xx: sparse fixesKim Phillips
fdt.c:91:78: warning: Using plain integer as NULL pointer fdt.c:103:78: warning: Using plain integer as NULL pointer speed.c:55:11: warning: symbol 'corecnf_tab' was not declared. Should it be static? speed.c:519:5: warning: symbol 'do_clocks' was not declared. Should it be static? mpc8313erdb.c:73:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:74:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:75:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:76:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:79:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:80:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:81:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:82:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:85:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:86:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:87:17: warning: obsolete struct initializer, use C99 syntax mpc8313erdb.c:88:17: warning: obsolete struct initializer, use C99 syntax Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04powerpc/mpc85xx: sparse fixesKim Phillips
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static? cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static? bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart' bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write' bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write' bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio' bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write' bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write' bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec' bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect' ngpixis.c:245:1: error: directive in argument list ngpixis.c:247:1: error: directive in argument list Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-03Merge remote-tracking branch 'u-boot-ti/master'Albert ARIBAUD
2012-11-02am335x_evm: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG supportTom Rini
We add CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set the variables and then fdtfile and findfdt to make us of this. It is now possible to do 'run findfdt' to have fdtfile be set to the value of the dtb file to load for the board we are running on. Signed-off-by: Tom Rini <trini@ti.com>
2012-11-02am335x: add initial AM335x IDK board supportMatthias Fuchs
This patch extends the am335x_evm board for the AM335x IDK. The IDK board uses MII for the ethernet phy (same as Beaglebone board) and MMC0 for storage (but without card detect line). The IDK uses UART3 for console. So u-boot must be build with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for the am335x_evm_uart3 board configuration as introduced by Andrew Bradfords recent patch series "am33xx: Enable UART {1,2,3,4,5}...". When using the IDK with console on UART0, those patches are not required. In this case the board slightly needs to be modified. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-10-30am335x: add mux config for DDR3 version of beagleboneKoen Kooi
This fixes the following boothang in SPL: Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ### Future commits will add pinmuxes for more on-board peripherals. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
2012-10-30eco5pk: Add new board and default configRaphael Assenat
Signed-off-by: Raphael Assenat <raph@8d.com> [trini: Squash boards.cfg / MAINTAINERS change into main patch] Signed-off-by: Tom Rini <trini@ti.com>
2012-10-30New board support: Nokia RX-51 aka N900Pali Rohár
Based on previous work by: Alistair Buxton <a.j.buxton@gmail.com> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Cc: Ивайло Димитров <freemangordon@abv.bg>
2012-10-29ARM: tegra: don't request GPIO from Seaboard's SPLStephen Warren
Seaboard has a GPIO that switches an external mux between Tegra's debug UART and SPI flash. This is initialized from the SPL so that SPL debug output can be seen. Simplify the code that does this, and don't actually request the GPIO in the SPL; just program it. This saves ~4.5K from the size of the SPL, mostly BSS due to the large gpio_names[] table that is no longer required. This makes Seaboard's SPL fit within the current max size. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Allen Martin <amartin@nvidia.com> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29ARM: tegra: select between Seaboard/Ventana at compile timeStephen Warren
Seaboard and Ventana are very similar boards, and so share the seaboard.c board file. The one difference needed so far is detected at run-time by calling machine_is_ventana(). This bloats the Ventana build with code that is never used. Switch to detecting Ventana at compile time to remove bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit within the max size. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
generated by cgit (git 2.34.1) at 2025-01-06 13:17:57 +0000