summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2020-05-01board: apalis_imx6: Add KSZ9131 phy skew settingsPhilippe Schenker
This patch adds skew register settings for KSZ9131. It checks first which phy is on the board and then applies the correct skew settings. Skew settings calculation for the KSZ9131: The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All PCB traces where routed exactly the same length so we can calculate the skew settings without taking the length into consideration. The traces are all length matched. RXC skew (PHY to MAC): - We use the 2ns DLL controlled delay on the PHY - We do not use the skew registers This results in the following values: RXC PHY fixed Delay 2000ps PHY Added Delay 0ps T_setup_R min 2.00ns T_setup_R typ 2.00ns T_setup_R max 2.00ns T_hold_R min 1.60ns T_hold_R typ 2.00ns T_hold_R max 2.40ns That means we are well within RGMII specs. TXC skew (MAC to PHY): - We use the 2ns DLL controlled delay on the PHY - We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew register in a resulting ~1.4ns delay. This results in the following values under consideration of the tolerances: TXC min TXC typ TXC max MAC min -100ps -100ps -100ps MAC max 900ps 900ps 900ps PHY fixed Delay 2000ps 2000ps 2000ps PHY added Delay -340ps -600ps -859ps T_setup_T min 1.56ns 1.30ns 1.04ns T_setup_T typ 2.06ns 1.80ns 1.54ns T_setup_T max 2.56ns 2.30ns 2.04ns T_hold_T min 1.04ns 1.30ns 1.56ns T_hold_T typ 1.94ns 2.20ns 2.46ns T_hold_T max 2.84ns 3.10ns 3.36ns This shows that T_hold_T min and T_setup_T min times are out of spec for RGMII timing. However the KSZ9131 has a minimal value for this time of 0.8ns which is met under all circumstances. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2020-05-01board: verdin-imx8mm: Add KSZ9131 phy skew settingsPhilippe Schenker
This patch determines which phy is placed on the board with the PHY ID then it sets the same settings for KSZ9031 as before but for KSZ9131 it enables both RXC and TXC delay lines in the PHY. This will compensate the missing delay from the MAC. Other skew settings are not needed as the traces on board are routed exactly the same length Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-05-01verdin-imx8mm: Change board phy skew values for our ksz9031Philippe Schenker
This patches uses the existing functions for interacting with the KSZ9031 and uses the values appropriate for our board. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-05-01mx8mq_evk: Remove unrelated commentFabio Estevam
The comment does not relate to the setup_i2c() function, so just remove it. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-05-01imx8mp_evk: Remove unrelated commentFabio Estevam
The comment does not relate to the setup_i2c() function, so just remove it. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-05-01imx: imx8m*: Remove do_reset from board filesClaudius Heine
Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL instead. It is very close to what is done here, anyway, and plays more nicely with the rest of U-Boot than adding a custom `do_reset` implementation into board files. `do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the addr parameter while the boards are passing WDOG1_BASE_ADDR. This is ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by default if 0 is passed in. Co-Authored-by: Harald Seiler <hws@denx.de> Signed-off-by: Claudius Heine <ch@denx.de> Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
2020-05-01imx8: Configure SNVSFranck LENORMAND
Add a module to configure the tamper and secure violation of the SNVS using the SCU API. The module also adds some commands: - snvs_cfg: Configure the SNVS HP and LP registers - snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP) - tamper_pin_cfg: Change the configuration of the tamper pins - snvs_clear_status: Allow to write to LPSR and LPTDSR to clear status bits Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-04-30Merge tag 'xilinx-for-v2020.07-rc2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx changes for v2020.07-rc2 mmc: - Fix dt property handling via generic function clk: - Fix versal watchdog clock setting nand: - Fix zynq nand command comparison xilinx: - Enable ubifs - Sync board_late_init configurations with initrd_high setup - Make custom distro boot more verbose zynq: - Kconfig alignments - Fix nand cse configuration zynqmp: - Fix zcu104 low level qspi configuration - Small DT updates Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-30Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb, ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb. - Add GICv3 support for ls1028a, ls2088a, ls1088a. - Add lpuart support on ls1028aqds. - Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based platforms.
2020-04-29Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
- rmobile gen2/gen3 DTS sync and defconfig consolidation
2020-04-29driver: net: fm: add DM ETH supportMadalin Bucur
Probe the FMan MACs based on the device tree while retaining the legacy code/functionality. One notable change introduced here is that, for DM_ETH, the name of the interfaces is corrected to the fmX-macY format, that avoids the referral to the MAC block names which were incorrect for FMan v3 devices (i.e. DTSEC, TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1). The legacy code is left unchanged in this respect. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-29configs: ls1028aqds: add lpuart configYuantian Tang
Add lpuart config to enable lpuart feature. Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Yuantian Tang <andy.tang@nxp.com>. Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-29board: freescale: ls1028a: mux changes for lpuartYuantian Tang
mux changes in board file to enable lpuart1 and macro define for lpuart1 used for mux changes in board configuation register 13 Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com> Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-29board: ls2088ardb: transition to DM_ETHIoana Ciornei
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2 Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH is activated. Also, force the PCI devices to be enumerated at probe time. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-29board: ls1088ardb: transition to DM_ETHIoana Ciornei
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2 Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH is activated. Also, force the PCI devices to be enumerated at probe time. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-28ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.6.2Marek Vasut
Synchronize R-Car Gen3 device trees with Linux 5.6.2, commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a . Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-04-28ARM: rmobile: Unify Gen3 Salvator-X(S) and ULCB defconfigsMarek Vasut
The r8a779{5,6,65}_salvator-x and r8a779{5,6,65}_ulcb_defconfig were building the same target, except for the default DT. The default DT is however only a detail, as the actual DT to be used to configure U-Boot is detected automatically based on the CPU ID, hence the default DT is not meaningful. Unify each three defconfigs per board to reduce the duplication. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-04-28fsl-layerscape: Move GIC RD tables init to soc.cHou Zhiqiang
Move GIC redistributor tables initialization to CPU setup function. This patch introduces a GIC redistributor tables init function, and moves the function of reserving memory for GIC redistributor tables to soc.c and adds a argument for the memory size to reserve, BTW rename the function so that it is more readable. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-28board: lx2160a: Align RD tables address to 64KBHou Zhiqiang
As the lower 16bit of the redistributor pending table is reserved for describing the memory attributes, we must give a 64KB aligned address to the GIC LPI initialization function. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-28board: lx2160a: Add check in GIC RD tables initHou Zhiqiang
Program the GIC redistributor tables only when succeeded to reserve memory for them, otherwise kernel will lose the chance to program them using allocated memory. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Wasim Khan <wasim.khan@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-28armv8: ls1046ardb: update the DIMM WRLVL_START valueYuantian Tang
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ. Update DDR struct to set new WRLVL_START values so that the new DIMM MTA18ADF2G72AZ get optimized and the old DIMM still works. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-27Merge tag 'mips-pull-2020-04-27' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-mips - brcmnand: fix missing code path from Linux driver - bmips: fix build error when disabling USB - mips: add option to restore original exception vector base - mips: fix off-by-one error when clearing gd_data - mips: minor fixes for compatibility with generic SPL framework - spl: refactor legacy image loading - spl: add LZMA decompression support for legacy images - Makefile: add target to build LZMA compressed U-Boot images - mtmips: refactor and rewrite low-level init code - mtmips: add and enable SPL support with LZMA - mtmips: add support for MT7628 reference board - mtmips: add support for VoCore/VoCore2 board
2020-04-27mips: Add support for SoM "VoCore2".Mauro Condarelli
Small patch to add support for VoCore/VoCore2 board. VoCore is open hardware and runs OpenWrt/LEDE. It has WIFI, USB, UART, 20+ GPIOs but is only one inch square. It will help you to make a smart house, study embedded system or even make the tiniest router in the world. Details about this SoM can be found at "https://vocore.io/v2.html". Signed-off-by: Mauro Condarelli <mc5686@mclink.it> Reviewed-by: Stefan Roese <sr@denx.de>
2020-04-27mips: mtmips: add support for mt7628-rfbWeijie Gao
This patch adds support for mt7628 reference board. SPL_DM and DT are not enabled for SPL to save about 17KiB for u-boot-spl.bin. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2020-04-27mips: mtmips: enable SPL for all boardsWeijie Gao
This patch enables SPL for all mtmips boards. And also remove defconfig files which are intend to build ram bootable u-boot files. SPL_DM and OF_CONTROL are enabled for both boards. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2020-04-27xilinx: Move bootmode detection to separate functionMichal Simek
Create special function for reading bootmode on Versal and ZynqMP. Zynq is using specific function (without mask) already. Future patches will be calling this function from different location too. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27xilinx: Move initrd_high setup to common locationMichal Simek
Moving to common location initrd_high is also setup for Zynq which hasn't done in run time code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27xilinx: zynqmp: Fix MIO 18 configuration on zcu104 revCMichal Simek
Without this change QSPI is not detected on zcu104 revC. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27xilinx: Introduce board_late_init_xilinx()Michal Simek
This function should keep common shared late configurations for Xilinx SoCs. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-27ARC: HSDK-4xD: make init status resistant to U-boot reloadingEugeniy Paltsev
Use register intstead of static variable to store HSDK init status as we want to avoid the situation when we reload U-boot via MDB after previous init is done but HW reset (board reset) isn't done. So let's store the init status in unused register - CREG_CPU_0_ENTRY so status will survive after U-boot is reloaded via MDB. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: use separate config fileEugeniy Paltsev
HSDK-4xD has quite different environment so let's split HSDK and HSDK-4xD configs file. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: tweak memory mapEugeniy Paltsev
For HSDK-4xD we do additional AXI bridge tweaking while doing hsdk_init command: - we shrink IOC region. - we configure ARC HS CORE SLV1 aperture depending on haps_apb_location environment variable. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: add CSM configuration supportEugeniy Paltsev
Add support for CSM enable/disable and CSM relocation via hsdk_init command. We allow to relocate CSM to the beginning of any aperture even if HW support finer granularity. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: add support for SLC enable/disableEugeniy Paltsev
Add support for SLC enable/disable via hsdk_init command. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: print timer clock valueEugeniy Paltsev
Print timer clock value in hsdk_clock print_all command. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: drop additional GPU clock infoEugeniy Paltsev
HSDK-4xD has other GPU type so it consumes only GPU core clock. Even we have additional GPU clock dividers they are not routed to anything. So drop information about those additional clocks in hsdk_clock print_all command. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: print info about HDMI clocksEugeniy Paltsev
HSDK-4xD has HDMI working so let's print info about HDMI clocks. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: fix headerize script for HSDK-4xD compatibilityEugeniy Paltsev
ARC HS CPU in HSDK-4xD has ARC ID = 0x54, so fix headerize script accordingly. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: use active low polarity of cpu_start pulseEugeniy Paltsev
Add quirk for HSDK-4xD - due to HW issues HSDK can use any pulse polarity but HSDK-4xD require active low polarity of cpu_start pulse. So use low polarity of cpu_start pulse for both board. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-27ARC: HSDK-4xD: add initial board supportEugeniy Paltsev
Add initial HSDK-4xD board support. The ARC HS4x/HS4xD Development Kit includes a multicore ARC HS4xD-based chip that integrates a wide range of interfaces including Ethernet, HDMI, WiFi, Bluetooth, USB, SDIO, I2C, SPI, UART, I2S, ADC, PWM and GPIO, as well as a Think Silicon GPU. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2020-04-24arm: actions: Add common framework for Actions Owl Semi SoCsAmit Singh Tomar
This commit adds common arch support for Actions Semi Owl series SoCs and removes the Bubblegum96 board files. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
2020-04-23Revert "riscv: qemu: clear kernel-start/-end in device tree as workaround ↵Lukas Auer
for BBL" The commit was added as a workaround required in QEMU when using BBL as the supervisor binary interface (SBI) for Linux. We are now using OpenSBI to provide the SBI, the workaround is therefore not required anymore and can be removed. This reverts commit 897206c5cc5c6ac0dc2ab851044e42baada3785b. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-04-21Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Backplane support and bug fixes
2020-04-20Merge tag 'ti-v2020.07-rc1' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Fix boot on am335x guardian board - Increase OPSI speed on AM65x and J721E devices - Use JTAD register for identifying K3 devices. - Update TI entry in MAINTAINERS file.
2020-04-20Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-imxTom Rini
2020-04-20t208xqds: add support for backplane krFlorinel Iordache
Add support for backplane kr on t208xqds: remove board specific fixups on t208xqds for ethernet interfaces specified in device tree as supported backplane modes. Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20lx2160aqds: add support for backplane krFlorinel Iordache
Add support for backplane kr on lx2160aqds: remove board specific fixups on lx2160aqds for ethernet interfaces specified in device tree as supported backplane modes. Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20ls1046aqds: add support for backplane krFlorinel Iordache
Add support for backplane kr on ls1046aqds: remove board specific fixups on ls1046aqds for ethernet interfaces specified in device tree as supported backplane modes. Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20armv8: ls1028a: define esdhc_status_fixupYinbo Zhu
This patch is to define esdhc_status_fixup function for ls1028a to disable SDHC1/SDHC2 status in device tree node if not selected. Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20board: fsl: lx2160a: unused variable gic_lpi_baseHeinrich Schuchardt
If the board is configured without CONFIG_GIC_V3_ITS, an error occurs: board/freescale/lx2160a/lx2160a.c: In function ‘ft_board_setup’: board/freescale/lx2160a/lx2160a.c:673:6: error: unused variable ‘gic_lpi_base’ [-Werror=unused-variable] 673 | u64 gic_lpi_base; | ^~~~~~~~~~~~ Let's define the variable as __maybe_unused. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-10 17:25:07 +0000