summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2018-01-28arm: add support for PDU001Felix Brack
This patch adds support for the PDU001 board. Signed-off-by: Felix Brack <fb@ltec.ch> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-28bcm283x: Add pinctrl driverAlexander Graf
The bcm283x family of SoCs have a GPIO controller that also acts as pinctrl controller. This patch introduces a new pinctrl driver that can actually properly mux devices into their device tree defined pin states and is now the primary owner of the gpio device. The previous GPIO driver gets moved into a subdevice of the pinctrl driver, bound to the same OF node. That way whenever a device asks for pinctrl support, it gets it automatically from the pinctrl driver and GPIO support is still available in the normal command line phase. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-01-28rockchip: pinctrl: rv1108: Move the iomux definitions into pinctrl-driverDavid Wu
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h, and move them into pinctrl-driver. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28ARM: AM43XX: Call hw_data_init() again after relocation to update *ctrlFaiz Abbas
hw_data_init() is called before relocation to initialise hardware data. Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be updated during relocation and will hold a stale value. Therefore call hw_data_init() again after relocation to reinitialize *ctrl. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-01-28clk: clk_stm32f: Move SYSCFG clock setup into configure_clocks()Patrice Chotard
Move SYSCFG clock setup into configure_clocks() instead of calling clock_setup() from board file. As this clock is only needed in case of ethernet enabled and as both stm32f4 and stm32f7 are using the Designware ethernet IP, we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed. Move the RMII setup from board_early_init_f() to board_init() to insure that RMII bit is set only when clock driver is initialized. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-28clk: clk_stm32f: Remove STMMAC clock setupPatrice Chotard
Thanks to 'commit ba1f96672522 ("net: designware: add clock support")' we don't need anymore to setup the STMMAC clock in board. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2018-01-28board: stm32: Add stm32f429-evaluation board supportPatrice Chotard
Add stm32f429-evaluation board support. For more information, please visit: http://www.st.com/en/evaluation-tools/stm32429i-eval.html Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-27Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2018-01-27ARM: rmobile: Convert R8A7791 Porter board to DM and DTMarek Vasut
Convert the R8A7791 Porter board to DM and DT. This implies mostly enabling the necessary configuration options and plucking out the ad-hoc configuration from the board file. Moreover, the pre-reloc malloc size was increased to allow the clock driver to start up early without running out of malloc space and the early stack was moved further up in the DRAM to avoid rewriting U-Boot itself. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-27sunxi: Transition from the MMC to a FAT-based environmentMaxime Ripard
The current environment has been hardcoded to an offset that starts to be an issue given the current size of our main U-Boot binary. By implementing a custom environment location routine, we can always favor the FAT-based environment, and fallback to the MMC if we don't find something in the FAT partition. We also implement the same order when saving the environment, so that hopefully we can slowly migrate the users over to FAT-based environment and away from the raw MMC one. Eventually, and hopefully before we reach that limit again, we will have most of our users using that setup, and we'll be able to retire the raw environment, and gain more room for the U-Boot binary. Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2018-01-26Merge git://git.denx.de/u-boot-mipsTom Rini
2018-01-26Merge git://git.denx.de/u-boot-spiTom Rini
2018-01-26MIPS: add BMIPS Comtrend AR-5315u boardÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-26MIPS: add BMIPS Comtrend WAP-5813n boardÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-25boston: Pad binary in .mcs to a multiple of 16 bytesPaul Burton
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the final 0x00 byte which ends the .relocs section seems to be skipped & left in flash as 0xff unless the data contained in the .mcs is padded out to a 16 byte boundary. Without our final zero byte relocation will fail with an error about a spurious reloc: Avoid this problem by padding out the data in the .mcs file to a 16 byte boundary using srec_cat's -range-pad functionality. Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-01-24wait_bit: use wait_for_bit_le32 and remove wait_for_bitÁlvaro Fernández Rojas
wait_for_bit callers use the 32 bit LE version Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-23Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-23fsl: common: qixis: Add ifc and emmc switching via qixisAshish Kumar
Currently only SD, NAND can be secondary boot sources controlled by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR can be secondary boot source, while QSPI-NOR is the primary. Add options in qixis to switch to other boot sources including ifc and emmc. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23armv8: ls1088a: vid: Compiling VID specific functions for SPLRajesh Bhagat
Enables and compiles VID specific functions for SPL. Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23ls1088a: Add VID support for QDS and RDB platformsRajesh Bhagat
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems. It reads the fusesr register and changes the VDD accordingly by adjusting the voltage via LTC3882 regulator. This patch also takes care of the special case of 0.9V VDD is present in fusesr register. In that case,it also changes the SERDES voltage by disabling the SERDES, changing the SVDD and then re-enabling SERDES. Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23common: board_f: vid: Add VID specific API to adjust core voltageRajesh Bhagat
Adds a VID specific API in init_sequence_f and spl code flow namely init_func_vid which is required to adjust core voltage. VID specific code is required in spl, hence moving flag CONFIG_VID out of spl flags. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23ls1088a: ddr: configure DDR for 0.9v for VID supportRajesh Bhagat
When VID feature is supported, check the contents of fuse register and configure DDR operate at 0.9v. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23Kconfig: Add LTC3882 voltage regulator configRajesh Bhagat
Adds below LTC3882 voltage regulator config: CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Move IR chip specific code in flagRajesh Bhagat
Moves IR chip (IR36021) specific code in flag to resolve compilation issue where it is not present. For example, LS1088A is having a new LTC3882 voltage chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add board specific vdd adjust APIRajesh Bhagat
Adds a board specific API namely board_adjust_vdd which is required to define the board VDD adjust settings. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common:vid: Add LS1088A VID Supported voltage valuesRajesh Bhagat
Adds below voltage values supported by LS1088A Soc: 1.025V(default), 0.9875V, 0.9750V, 0.9V, 1.0V, 1.0125V, 1.0250V. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-22ARM: omap3_logic: Enable SPL_OF_CONTROL and SPL_OF_PLATDATAAdam Ford
The SPL doesn't have much room, so in order to support OF_CONTROL in SPL, we need the extra functionality of SPL_OF_PLATDATA. Adding these features allows us to remove a small part of code without losing the serial port during SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-19powerpc: Drop unreferenced CONFIG_* definesTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_CYRUS CONFIG_IDS8313 CONFIG_MPC8308_P1M CONFIG_MPC8308RDB CONFIG_MPC8349EMDS CONFIG_MPC8349ITXGP CONFIG_SBC8349 CONFIG_SBC8548 CONFIG_SBC8641D CONFIG_TQM834X CONFIG_VE8313 CONFIG_XPEDITE5140 CONFIG_XPEDITE5200 CONFIG_XPEDITE550X Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Mario Six <mario.six@gdsys.cc>
2018-01-19m68k: Drop unreferenced CONFIG_* definesTuomas Tynkkynen
The following config symbols are only defined once and never referenced anywhere else: CONFIG_AMCORE CONFIG_ASTRO5373L CONFIG_M52277EVB CONFIG_M5253DEMO CONFIG_M5253EVBE CONFIG_M5275EVB CONFIG_M54418TWR CONFIG_STMARK2 Most of them are config symbols named after the respective boards which seems to have been a standard practice at some point. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-01-19ARM: qemu-arm: Add support for AArch64Tuomas Tynkkynen
This adds support for '-machine virt' on AArch64. This is rather simple: we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig symbols, provide the ARMv8 memory map from the board file and add a new defconfig based on the 32-bit defconfig. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19ARM: dts: omap3-beagle{-xm}: Enable DM and devicetree for BeagleBoardDerald D. Woods
This commit updates the configuration files needed to support OF_CONTROL on the OMAP3 BeagleBoard(s).
2018-01-19ARM: dts: am574x-idk: Add initial supportLokesh Vutla
Add initial dts support for am574x-idk Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19board: ti: am574x-idk: Update pinmux using latest PMTLokesh Vutla
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the board files named am574x_idk_v1p3b_sr2p0 that were auto generated on 13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>". Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19board: ti: am574x-idk: Add ddr data supportLokesh Vutla
AM574x-idk has the following DDR parts attached: EMIF1: MT41K256M16HA (1GB with ECC) EMIF2: MT41K256M16HA (1GB without ECC) Enabling 2GB DDR without interleaving between EMIFs. And enabling ECC on EMIF1. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
2018-01-19board: ti: am574x-idk: Add hw data supportLokesh Vutla
Update prcm, voltages and pinmux support for am574x-idk. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19board: ti: am574x-idk: Add epprom supportLokesh Vutla
am574x-idk is a board based on TI's am574 processor Add eeprom support. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19arm: dra762: Add support for device package identificationLokesh Vutla
DRA762 comes in two packages: - ABZ: Pin compatible package with DRA742 with DDR@1333MHz - ACD: High performance(OPP_PLUS) package with new IPs Both the above packages uses the same IDCODE hence needs to differentiate using package information in DIE_ID_2. Add support for the same. Also update clock, ddr, emif information. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19board: ti: k2g: Make ddr3* declarations as staticLokesh Vutla
All ddr3_emif declarations are not used outside ddr3_k2g.c file. So make all of them as static. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19board: ti: dra76: mux wakeup2 as gpio1_2Tomi Valkeinen
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux the pin as gpio and PIN_INPUT. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-01-19board: ti: K2G FC SoC 1GHz and DDR3 1066 MT/s supportRex Chang
Added support for K2G EVM with FlipChip SoC of which ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also backward compatible with old revision EVM and EVM with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s. The new SoC supports 2 different speeds at 1GHz and 600MHz. Modyfied the CPU Name to show which SoC is used in the EVM. Modified the DDR3 configuration to reflect New SoC supports 2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT. Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz, and set the u-boot env variable board_name accordingly. Modified findfdt script in u-boot environment variable to include new k2g board type. Signed-off-by: Rex Chang <rchang@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19board: ti: dra7xx: Select MCAN instead of DCAN on DRA76 EVMVignesh R
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance to use if any at all is done through CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is handled in U-boot. Handle this additional pinmuxing requirement in U-boot to ensure that MCAN is used by default via the DCAN1 pins. Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> [fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN] Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-01-17Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-17freescale: Ensure common commands are not included in SPL binaryTom Rini
Both the "qixis_reset" and esbc_validate" commands can only be used in full U-Boot so do not build them in SPL. As part of this rework the qixis code to declare things as static and make use of __weak for function aliases. Cc; York Sun <york.sun@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-15sunxi: arm64: correct usage of DT node address in FIT generationAndre Przywara
The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Adjust the FIT build script for 64-bit Allwinner boards to remove the bogus addresses from the node names and avoid the warnings. This avoids a warning with recent versions of the dtc tool. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2018-01-15Merge git://git.denx.de/u-boot-imxTom Rini
2018-01-15db410c: use the device tree parsed by the lk loader.Jorge Ramirez-Ortiz
We dont need to keep copies of the properties that we are going to fixup since we will be using the dtb provided by the firmware. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db410c: replace reset driver with psciJorge Ramirez-Ortiz
this should be the norm for armv8 platforms. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db410c: update wlan and bt mac addresses from firmwareJorge Ramirez-Ortiz
The firmware that runs before u-boot modifies u-boot's device tree adding the local-mac-address and local-bd-address properties for the compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan". This commit reads that firmware, retrieves the properties and fixups the device tree that is passed to the kernel before booting. Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2018-01-15db820c: stop autoboot when vol- pressedJorge Ramirez-Ortiz
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
generated by cgit (git 2.34.1) at 2024-12-26 23:10:36 +0000