summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-11-03imx: support i.MX8QM ROM 7720 a1 boardOliver Graute
Add i.MX8QM ROM 7720a1 board support Boot log as below: U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200) CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Advantech iMX8QM Qseven series Board: ROM-7720-A1 4GB Build: SCFW 65afe5f6 Boot: SD2 DRAM: 4 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1 , eth-1: ethernet@5b050000 Hit any key to stop autoboot: 0 Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Cc: uboot-imx <uboot-imx@nxp.com>
2019-11-03board/BuR/brppt2: initial commitHannes Schmelzer
This commit adds support for the brppt2 board. The board is based on the i.mx6 dual-lite SoC. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-11-03imx8mm: evk: enable bd71837 pmicPeng Fan
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for DRAM and linux suspend voltage requirement. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03imx8m: evk: spl: probe clk in spl early stagePeng Fan
We are going to add i2c pmic support before dram could be used. So we need enable clk driver earlier, so use spl_early_init and move clock controller probe eariler to board_init_f. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03opos6uldev: migrate to DM_VIDEOSébastien Szymanski
Migrate to DM_VIDEO, update the device tree and remove code that is no longer necessary. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-11-03ARM: imx: Convert mccmon6 to use fitImage instead of uImage+DTBLukasz Majewski
This commit enabled support for fitImage on mccmon6 when we switch to DT/DTS (including falcon mode). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Decouple mccmon6's SPL and u-boot proper codeLukasz Majewski
The mccmon6 has been used a "mixed" approach between SPL and U-Boot proper sources. This commit decoupes SPL and u-boot proper, which allows clear distinction between those two code bases and facilitates conversion to DM/DTS on this particular board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Convert mccmon6 to use DM/DTS in the u-boot properLukasz Majewski
This commit converts mccmon6's u-boot proper (in a single commit to avoid build breaks) to use solely DM/DTS. The DTS description of the mccmon6 has been ported from Linux kernel (v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx6: DHCOM i.MX6 PDK: spl: Add eMMC initialization to SPL codeClaudius Heine
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0). Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03ARM: imx6: DHCOM i.MX6 PDK: fix board_boot_modes emmc entryClaudius Heine
The board_boot_modes contained the wrong values for the emmc entry. The eMMC here is connected over a 8-bit bus. This change allows to use the 'bmode emmc' command to boot from emmc. Signed-off-by: Claudius Heine <ch@denx.de>
2019-11-03ARM: dts: imx6ull-colibri: change hierarchy of DTS filesIgor Opaniuk
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to keep original imx6ull-colibri.dts in sync with Linux. Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi + additionally fix checkpatch warnings. Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-10-30Merge branch '2019-10-28-azure-ci-support'Tom Rini
- Clean up Travis-CI slightly and then add support for Microsoft Azure pipelines, all from Bin Meng.
2019-10-30Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- H6 dts(i) sync (Clément) - H6 PIO (Icenowy) - Fix pll1 clock calculation (Stefan) - H6 dram, half DQ (Jernej) - A64 OLinuXino eMMC (Sunil)
2019-10-29arm: mvebu: Avoid generating kwbimage.cfg in the source treeBin Meng
At present some boards generate kwbimage.cfg in the source tree during the build. This breaks buildman testing on some systems where the source tree is read-only. Update makefile rules to generate it in the build tree instead. Note some other boards have the kwbimage.cfg file written in advance, hence we need check if the file exists in the build tree first, otherwise we fall back to one in the source tree. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-25Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mipsTom Rini
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs - bmips: various small fixes - mtmips: add new drivers for clock, reset-controller and pinctrl - mtmips: add support for high speed UART - mtmips: update/enhance drivers for SPI and ethernet - mtmips: add support for MMC
2019-10-25Merge branch '2019-10-24-ti-imports'Tom Rini
- Enable DFU on dra7xx boards - Further Keystone 3 platform improvements
2019-10-25armv7R: K3: j721e: Add support for triggering ddr init from SPLLokesh Vutla
In SPL, DDR should be made available by the end of board_init_f() so that apis in board_init_r() can use ddr. Adding support for triggering DDR initialization from board_init_f(). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- DWC3 improvements - i.MX7 EHCI bugfix
2019-10-25Merge tag 'u-boot-atmel-2020.01-b' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel features and fixes for 2020.01 cycle This feature set includes Eugen's work on a new tiny flexcom driver and eeprom mac retrieval for the sam9x60-ek board.
2019-10-25bmips: correct name charactersÁlvaro Fernández Rojas
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-25arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)Sunil Mohan Adapa
A64 OLinuXino board from Olimex has three variants with onboard eMMC: A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In addition, there are two variants without eMMC. One without eMMC and one with SPI flash. This suggests the need for separate device tree for the three eMMC variants. The Linux kernel upstream has chosen to create and use a separate device tree for the eMMC variants instead of adding eMMC support existing device tree. These changes to Linux kernel are queued for Linux 5.4. commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)") This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux device-tree and a64-olinuxino_defconfig. Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org> [jagan: updated linux-next commit details] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-24ARM: zynq: Remove unused board_early_init_f()Michal Simek
board_early_init_f added by commit e6cc3b25d721 ("arm: zynq: Wire watchdog internals") is no longer needed that's why remove it also with Kconfig enabling. Fixes: ccd063e9812a ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Convert invoke_smc() to xilinx_pm_request()Michal Simek
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to xilinx_pm_request() which do calculation with PM_SIP_SVC already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24board: sam9x60ek: add support for MAC address retrievalEugen Hristev
Retrieve mac address from i2c eeprom at boot time. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-24ARM: keystone: Do not enable the USB power domains at the board levelJean-Jacques Hiblot
This breaks linux boot sequence. Observed on k2e and k2l platforms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-23Merge tag 'u-boot-stm32-2019-10-23' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Disable CONFIG_NET flag for MCU STM32 - Fix ramdisk_addr_r for stm32f746-disco - Fix USB product id for stm32mp1
2019-10-22board: stm32mp1: fixup the usb product id for USB download gadgetPatrick Delaunay
Select the correct USB product id used by the download gadget for ST stm32mp1 boards. The board stm32mp1 select the correct product id, as defined in http://www.linux-usb.org/usb.ids for the STMicroelectronics vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM): - dfu = 0xdf11 : STM Device in DFU mode it is the value used by ROM code and reused for stm32prog command - fasboot = 0x0afb : Android Fastboot device - others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM) Mass Storage Device it is used for UMS command / usb_dnl_ums This patch avoid conflict when the same USB VID/PID is used for ums, fastboot or dfu command (two different protocols associated to the same PID). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
2019-10-21board/ls1028a: Add call to sec_init()Udit Agarwal
Adds sec_init call to initialise the job ring parameters for secure boot operations. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-18Merge tag 'u-boot-amlogic-20191018' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - document alternative libretech-cc installation methods, including upstream TF-A and opensource tools - add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board - add support for Amlogic A311D based Khadas VIM3 - add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
2019-10-18configs: sei610: Add config file to fix userdata sizeGuillaume La Roque
Add separate config file to handle the different eMMC size on the sei610 board. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18boards: amlogic: add SEI610 supportNeil Armstrong
Add support for the customer board SEI610 manufactured by SEI Robotics with the following specifications: - Amlogic S905X3 ARM Cortex-A55 quad-core SoC - 2GB DDR4 SDRAM - 10/100 Ethernet (Internal PHY) - 1 x USB 3.0 Host - 1 x USB Type-C DRD - 1 x FTDI USB Serial Debug Interface - eMMC - SDcard - Infrared receiver - SDIO WiFi Module Like it's SEI510 counterpart, the boot flow is designed to boot Android AOSP built for the Yukawa Android device. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: Add Khadas VIM3 defconfigAndreas Färber
Derived from odroid-n2_defconfig and README.odroid-n2. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18board: amlogic: document alternative libretech-cc installation methodsDaniel Drake
As already documented in this README, several binaries must be glued together in order to boot the device. Extend the documentation to cover the prebuilt binaries (saving you the hassle of installing ancient cross-compilers), and also mention the open source replacements for the encryption tool (which is especially useful if you want to avoid requiring 32-bit x86 binaries in your build system). Signed-off-by: Daniel Drake <drake@endlessm.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: fu540: enable gpio driverSagar Shrikant Kadam
Enable the DM based GPIO driver for FU540-C000 SoC. Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-16arm: remove the H2200 boardHeinrich Schuchardt
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y. The maintainer Lukasz Dalek suggested to remove the board. https://lists.denx.de/pipermail/u-boot/2019-August/380685.html Cc: Lukasz Dalek <luk0104@gmail.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> [trini: As this is the last non-toradex PXA board, update travis too] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-14Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- vining_fpga updates
2019-10-14Merge tag 'u-boot-imx-20191014' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191014 ------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628 - logicpd pinmux - i.MX7ULP: imx_ddr_size - fixes Toradex i.MX6/i.MX7 - pico-imx7d - tpc70 converted to DM - New Board: meerkat96 - add HAB version command - i.MX8 : imx8: Jump from alias to OCRAM address at SPL init imx8qm/qxp: Set SPL TEXT base to OCRAM base
2019-10-14imx: imx8mm_evk: add board_mmc_get_env_devPeng Fan
Add board_mmc_get_env_dev to correctly return devno for mmc env Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-14mx7ulp_evk: Use imx_ddr_size()Fabio Estevam
Use imx_ddr_size() to retrieve the total DDR size instead of passing a hardcoded memory size. imx_ddr_size() calculates the memory size based on the actual MMDC registers values and is useful to detect misconfigurations, so switch to this more robust approach. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-10-13board: Add STM32F769 SoC, discovery board supportYannick Fertré
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13colibri_imx7: provide proper node name to pmic_getIgor Opaniuk
Implementation of pmic_get() uses uclass_find_device_by_name(), which behaviour was changed in 4213609cc7 ("drivers: core: use strcmp when find device by name"). Now we have to supply full node name with unit address. Fixes boot issue: U-Boot 2019.07-00788-g0ef6e69a1e-dirty (Jul 19 2019 - 15:27:02 +0300) CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 41C Reset cause: POR DRAM: 512 MiB initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19) ERROR Please RESET the board Fixes: 4213609cc7("drivers: core: use strcmp when find device by name") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-13imx: tpc70: Convert TPC70 (imx6q) board to use DM/DTS in SPL and u-bootLukasz Majewski
This patch converts the TPC70 to use driver model and device tree description in both SPL and u-boot proper. Notable changes (DM/DTS conversion): - PINCTRL{_IMX6} - DM_I2C - enable 'regulator' and 'pmic' commands - DM_MMC and BLK (USDHC) - DM_ETH - DM WDT (including SYSRESET) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: led: Enable LED default stateLukasz Majewski
This change sets the default state of LEDs on TPC70. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: cosmetic: Replace magic numbers when setting ENET clockLukasz Majewski
This is a cosmetic change, just to use proper define instead of magic numbers. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD bootLukasz Majewski
The TPC70 can boot from SD card (debug/development) and eMMC (production). The board_boot_order() function provides a run time check for the device from which one wants to boot (it is selected by GPIO pins setup). Moreover, a fallback to SD card is provided if the detection is not possible or working properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13ARM: imx6q_logic: Remove legacy pinmuxing code from board file.Adam Ford
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13board: tbs2910: Convert eth to driver modelSoeren Moch
So we can remove lots of legacy config code. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13board: tbs2910: Convert pci to driver modelSoeren Moch
So we can get rid of legacy pci config code. PCI_PNP is not required for this board, remove it to reduce the size of the u-boot binary. DM_PCI does not start the host controller automatically anymore. Do so in preboot instead. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-12Merge branch '2019-10-11-master-imports'Tom Rini
- Assorted cleanups - FAT bugfixes - mediatek platform updates
generated by cgit (git 2.34.1) at 2024-12-26 10:06:05 +0000