summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-10-08arm64: xilinx: Enable generic of_board_dtbIbai Erkiaga
Modify the configuration naming to be generic to xilinx rather than specific to Versal. The offset value is different for Zynq and ZynqMP to avoid overlapping with FSBL. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Move common board dtb searchIbai Erkiaga
Move the exisiting function of getting board dtb from versal to a common Xilinx folder. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: probe firmware driverIbai Erkiaga
Probe ZynqMP firmware driver on the board initialization phase and ensure that firmware is in place to continue execution. The probing is done on board_init so it can be used for both SPL and U-Boot proper. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: use firmware driver to get versionIbai Erkiaga
Use the new function from firmware version to get the firmware version. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08firmware: zynqmp: create firmware headerIbai Erkiaga
New firmware header to place firmware specific macro and function declarations. The patch also moves the macros defining PM operations as well as some helper macros. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Remove additional headersMichal Simek
There were several changes in past in this file without removing headers (watchdog cleanup, soft reset, etc). That's why remove additional useless headers. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Setup initrd_high and fdt_high at run timeMichal Simek
Setup initrd_high and fdt_high to be placed in lowmem space for kernel to be able to reach it. Values are setup at run time to ensure that the same setting can be used on different memory setup. Do this setting only when variables are not Similar run time detection was done for Zynqmp and Versal. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08microblaze: Remove unused variable ram_baseMichal Simek
This variable is completely unused that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add a2197 memory board revAMichal Simek
Similar to processor board but i2c structure is completely different. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add System Controller for a2197-g/pMichal Simek
Similar SCs but different wiring. - dc_i2c is connected to X-PRC cards that's why label is required to have an option to hook up some devices. - Exactly identify i2c devices on x-prc boards. In case of missing i2c connection devices won't be accessible. - USB 0 should be device mode with super speed. - USB 1 should be host mode. - Fix i2c mux reset pin entry - commented, not verified. - Fix i2c1 eeprom compatible string - it is an ST 128Kbit device. Need to use atmel fallback. - Fix si570 I2C slave address and add corresponding part numbers. - Enable AMS for system monitoring. - phy reset property should be commented because it will throw a warning dump when called from context that can sleep. No support for phys property (zynqmp phy driver) with SGMII. Add is-internal-pcspma property required by uboot. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
2019-10-08arm64: zynqmp: Add generic a2197 system controller configMichal Simek
Add generic configuration for a2197-p/-m/-g boards. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08ARM: zynq: Specify MMC controller number for boot sequenceMichal Simek
Xilinx Zynq SoC has two sdhci controllers but boot is only possible from the first one. That's why there is a need to specify controller number. mmc1 is supposed to be secondary boot device and should be also listed in distribution boot. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add idcodes for new RFSoC silicons ZU48DR and ZU49DRSiva Durga Prasad Paladugu
Add zu48dr and zu49dr to the list of zynqmp devices. The zu48dr and zu49dr are the new RFSoC silicons with id values of 0x7b and 0x7e. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Add new jtag distro boot commandSiva Durga Prasad Paladugu
This patch adds new jtag distro boot command to look for bootscript file in DDR and execute it first incase of jtag bootmode. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Add new dfu usb distro boot commandT Karthik Reddy
This patch adds new dfu usb distro boot command to look for bootscript from dfu-util and runs it. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
2019-10-08arm64: versal: Add new jtag distro boot commandSiva Durga Prasad Paladugu
This patch adds new jtag distro boot command to look for bootscript file in DDR and execute it first incase of jtag bootmode. This patch also updates scriptaddr to 512MB as there is high of script corruption incase of bigger kernel image. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Enable memory mapping via DTMichal Simek
Code reads DT and setup MMU table based on memory node. This will ensure that only DT needs to be changed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: zynqmp: Set initrd_high to as high as possibleT Karthik Reddy
This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Set initrd_high to as high as possibleSiva Durga Prasad Paladugu
This patch is setting up the initrd_high to as high as possible by leaving max stack size for u-boot so that bigger rootfs can also be loaded by u-boot for booting kernel. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: fpga: Add PL bit stream load supportSiva Durga Prasad Paladugu
This patch adds PL bitstream load support for Versal platform. The PL bitstream is loaded by making an SMC to ATF which in turn communicates with platform firmware which configures and loads PL bitstream on to PL. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08arm64: versal: Define board_late_init for versalSiva Durga Prasad Paladugu
Define board_late_init which performs bootmode detection and prepares corresponding distro boot commaand sequence. Also disable it for mini platforms because simply there is no need to have it enabled. But also disable it for virtual platform because Qemu is not modelling this register space that's why travis testing would fail. This configuration should be reverted when mainline Qemu is updated. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08xilinx: Add sd boot command script for referenceSiva Durga Prasad Paladugu
This patch adds sdboot command script for reference. This can be converetd into uboot script using mkimage and use for booting. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-08xilinx: Add qspi boot command script for referenceSiva Durga Prasad Paladugu
Thsi patch adds qspiboot command script for reference. This can be converetd into uboot script using mkimage and use for booting. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-06MAINTAINERS: Update my email addressMaxime Ripard
I'm not at bootlin anymore, and my mail address doesn't work any longer. Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-04ARM: dts: imx6q-logicpd: Add missing imx6q-logicpd-u-boot for SPLAdam Ford
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file which will enable these functions so SPL can properly setup UART, detect microSD card, and startup. Fixes: 8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled, remove MMC init") Signed-off-by: Adam Ford <aford173@gmail.com>
2019-10-04board: ti: am654: Disable TRNG node for HS devicesAndrew F. Davis
On HS devices the access to TRNG is restricted on the non-secure ARM side, disable the node in DT to prevent firewall violations. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-01rpi4: enable dram bank initializationMatthias Brugger
When booting through the efi stub, the memory map get's created by reading the dram bank information. Depending on the version of the RPi4 this information changes. Read the device tree to initialize the dram bank data structure. This way the kernel is able to access the whole range of available memory. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-16Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Add emmc hs200 support - Few bug fixes related to serdes, I2C, ethernet, etc
2019-09-13MAINTAINERS: Change fsl-qoriq, mpc86xx, mpc85xx maintainersPriyanka Jain
Change maintainers to Priyanka Jain for fsl-qoriq, mpc85xx Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-09-12lx2160: Correct serdes frequency print.Meenakshi Aggarwal
Suffix serdes frequency print with MHz Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: lx2160aqds: add support for SerDes protocol 14Florin Chiculita
Add SerDes1 protocol 14 in the list of supported protocols. This configuration enables one high-speed 100G port and PCIe x4. Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: lx2160aqds: fix ethernet-phy compatible propertyFlorin Chiculita
The code that generates the compatible property concatenates the ethernet phy id and clause-compatible information without separating them with a comma, resulting into no ethernet phy driver getting loaded by Linux kernel. Suffix phy_id_compatible_str with comma to fix this Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12board: fsl: lx2160a: implement board_fix_fdtPankaj Bansal
lx2160a rev1 and rev2 SoC has different pcie controller. The pcie controller device tree node fields "compatible" and registers names needs to be updated accordingly This change in device tree is handled as part of fdt fixups. These changes would only be applied if the soc revision is not rev1. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-11doc: lion_rk3368: use idbloader.img for rk3368Matwey V. Kornilov
Makefile now produces ready-to-deploy idbloader.img file. Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
2019-09-07Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Initial DM conversion
2019-09-06Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-bootTom Rini
- fix mailbox status register used for polling - fix bcm2835_sdhost to wait long enough for a transfer to complete - increase kernel image size from 8 MB to 64 MB on arm64 - add support for RPi4 - add prefixes for raspberry pi related stuff to git-mailrc
2019-09-06RPI: Add memory map for bcm2711Andrei Gherzan
Define the memory map for the BCM2711 based on the dt configuration available in the Raspberry Pi kernel fork. Signed-off-by: Andrei Gherzan <andrei@balena.io> [mb: BCM2838 -> BCM2711] Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-06RPI: Add entry for Raspberry Pi 4 model BAndrei Gherzan
The Raspebrry Pi 4 uses the new revision code scheme as documented by the foundation. This change adds an entry for this board as well. Signed-off-by: Andrei Gherzan <andrei@balena.io> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2019-09-04net: dwc_et_qos: update weak function board_interface_eth_initPatrick Delaunay
Align the board and driver prototype for board_interface_eth_init to avoid execution issue (the interface_type parameter is defined as int or phy_interface_t). To have a generic weak function (it should be reused by other driver) I change the prototype to use directly udevice. This prototype is added in netdev.h to allow compilation check and avoid warning when compiling with W=1 on file board/st/stm32mp1/stm32mp1.c warning: no previous prototype for 'board_interface_eth_init'\ [-Wmissing-prototypes] int board_interface_eth_init(int interface_type, .... ^~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-09-03Merge tag 'arc-for-2019.10-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-arc These are some very late changes mostly required to get 64-bit division working on ARC boards. For that we had to import missing parts of libgcc and add compiler flags to EMSDP which otherwise used very simple profile for compliation. And while at it another fix for EM SDP initialization is inluded as well.
2019-09-03arc: emsdp: Add more platform-specific compiler optionsAlexey Brodkin
Even though EM SDP is FPGA-based board and different FPGA images (known as .bit-files) are awailable for the board still there's a common subset of options we may rely on for all configs. These are: * Normalizer * Swap instructions * Simple multiplier * Barrel-shifter * Floating-point unit * Shorter instructions (code density) This among other improvements allows to compile code with 64-bit divisions, see [1]. [1] https://patchwork.ozlabs.org/patch/1156541/ Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Kever Yang <kever.yang@rock-chips.com>
2019-09-03arc: emsdp: Add initialization of PSRAMAlexey Brodkin
If the "Page Mode" is not enabled on the device, read operations from PSRAM may result in incorrect data. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-09-03riscv: ae350: use the v5l2 driver to configure the cacheRick Chen
Find the UCLASS_CACHE driver to configure the cache controller's settings. Signed-off-by: Rick Chen <rick@andestech.com> Cc: KC Lin <kclin@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-03riscv: sifive: fu540: set serial environment variable from otpSagar Shrikant Kadam
This patch sets the serial# environment variable by reading the board serial number from the OTP memory region. Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-09-02sh: r2dplus: Switch to DM PCI driverMarek Vasut
Add DT entry for the DM PCI driver, update board configs and drop ad-hoc board init code for the PCI bus. Instead, let the DM PCI driver initialize and operate the hardware. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-08-31Revert "vexpress64: fvp dram: add DRAM configuration"Ryan Harkin
This reverts commit fc04b923541d984b1544056fd3bfa8129d4e5aac where the FVP DRAM configuration was added. Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com>
2019-08-30siemens: avoid out of bound accessHeinrich Schuchardt
char num[1]; sprintf(num, "%d", i); leads to a buffer overrun. Simplify the overly complex coding. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Heiko Schocher <hs@denx.de>
2019-08-29Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xxTom Rini
Enable DM PCI for T2080RDB, T4240RDB, T1024RDB, T1042D4RDB, P1020RDB, P2020RDB, P2041RDB, P3041DS, P4080DS, and MPC8548CDS
2019-08-28powerpc: MPC85xxCDS: Disable legacy PCI fixup when DM_PCI is selectedHou Zhiqiang
Disable legacy PCI and PCIe fixup when CONFIG_DM_PCI is selected. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-28powerpc: MPC8548CDS: Compile legacy PCIe routines conditionallyHou Zhiqiang
Compile the legacy PCIe initialization routines only when DM_PCI is not enabled. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-24 00:35:37 +0000