summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2016-02-22ARM: zynq: Read memory size setting from DTMichal Simek
OF_CONTROL is setup by default and memory reading is done via DT. Remove all config files with memory references. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-21Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-02-21imx: mx6quq7: add sd card detectionJulien CORJON
Add board_mmc_getcd function and declare CD_GPIO for SDCard. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
2016-02-21imx: mx6quq7: specify max_bus_witdh directly in usdhc_cfgJulien CORJON
Specify max_bus_width directly in usdhc_cfg static definition instead of tweaking it in the board_mmc_init() function. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com>
2016-02-21imx: mx6quq7: fix USDHC4 declarationJulien CORJON
USDHC2 does not exist on mx6quq7 board, as USDHC4 was already been declared this is probably a typo. Signed-off-by: Julien Corjon <corjon.j@ecagroup.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-02-21board: tbs2910: Autoselect environment device when booting from SDSoeren Moch
Implement board specific functions to select the environment device and partition when booting from SD/MMC. SD2: mmc 0 0 SD3: mmc 1 0 eMMC: mmc 2 1 Signed-off-by: Soeren Moch <smoch@web.de>
2016-02-21mx7dsabresd: Make 'ums' command functionalFabio Estevam
When running the 'ums' command we get: => ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0xe18000 g_dnl_register: failed!, error: -22 ERROR: g_dnl_register failed at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage() Fix this by initializing USB OTG1 port as USB device mode instead of host. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21mx7dsabresd: Use Adrian's NXP email addressFabio Estevam
Use the new NXP email address for the board maintainer. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21x86: Add Intel Cougar Canyon 2 boardBin Meng
This adds basic support to Intel Cougar Canyon 2 board, a board based on Chief River platform with an Ivy Bridge processor and a Panther Point chipset. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-02-20Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-02-20vinco: add Maintainers fileAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
2016-02-19ARM: Add Support for the VInCo platformGregory CLEMENT
The Versatile Industrial Communication platform is a community oriented board from Landis + Gyr. It comes with: - an RS-485 port - 2 Ethernet ports - a wireless M-BUS - a 4G modem - a 4MB SPI flash - a 4GB eMMC Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> [rebase on current TOT] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18arm: at91: Add support for DENX MA5D4 SoM and EVKMarek Vasut
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI CAN controllers and DRAM, the baseboard contains UART connectors, ethernet port, microSD slot, LCD header, 2x CAN connector and a lot of expansion headers. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18board: atmel: clean up the PMC_PLLICPR init codeWenyou Yang
Due to introducing the PMC_PLLICPR init function, use this function to clean up the code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18board: atmel: siemens: clean up PLLB codeWenyou Yang
Due to introducing the new PLLB clock handle functions, use these functions to clean up the PLLB enable code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Tested-by: Heiko Schocher <hs@denx.de>
2016-02-18board: atmel: siemens: clean up UTMI PLL codeWenyou Yang
Due to introducing the new UTMI PLL clock handle functions, use the functions to reduce the duplicated code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-18board: atmel: clean up peripheral clock codeWenyou Yang
Due to introducing the new peripheral clock handle functions, use these functions to reduce duplicated code. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> [Rebased on current master, fixup for at91rm9200ek] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-16tegra: video: Convert tegra20 LCD driver to driver modelSimon Glass
Move this driver over to use driver model. This involves rearranging the code somewhat. The effect is that everything is run from the probe() method. Boards which use this are fixed up, but only seaboard is tested. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16tegra: video: Rename CONFIG_VIDEO_TEGRA to CONFIG_VIDEO_TEGRA20Simon Glass
This option refers only to the tegra20 video driver, so name it as such to avoid confusion with tegra124. Also move this option to Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-15ARM : DRA7: Switch QSPI to use MODE-0 at 64MHzVignesh R
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better throughput. Also, add IODelay parameters for the same. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-15OMAP3LOGIC: Update maintainerAdam Ford
I will take this over from Peter Barada, since I work with it daily at Logic PD. Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Peter Barada <peter.barada@logicpd.com>
2016-02-08sniper: Drop references to P970Paul Kocialkowski
There are various different boards with the same hardware sold as LG Optimus Black, such as P970, P970g and KU5900. Since this port is functional for all variants, it doesn't make sense to keep references to P970. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08rpi: set ethaddr as wellLubomir Rintel
Let's set "ethaddr" when we get the ethernet address too, so that fdt_fixup_ethernet() sets the address in the device tree and the Linux driver can pick it up. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
2016-02-08board: ti: ks2_evm: remove board_eth_init when CONFIG_DM_ETH is definedMugunthan V N
remove board_eth_init when CONFIG_DM_ETH is defined Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-08OMAP3: omap3_logic: Enable Android FastbootAdam Ford
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic. This patch sets up the USB gadget and Android Fastboot to match what is done in the omap3_beagle project. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08OMAP3: Enable SPL on omap3_logicAdam Ford
Previously, Omap3_logic assumed X-loader was present. With this patch, we can finally replace X-loader with an MLO generated by U-Boot. This requires ECC to be setup to match the Linux Kernel and the PBIAS confgured for the SD card. Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08rpi: fix up Model B entriesLubomir Rintel
The P5 header was not present on "Model B" any board prior to Revision 2.0, there's no need for a separate device tree. Also, it looks like "rev2" is incorrectly used to only cover the 512MiB memory models; there also were 256MiB 2.0 boards. I don't have all of the boards to check this, I'm following this table: http://elinux.org/RPi_HardwareHistory#Board_Revision_History Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2016-02-08rpi: link to another model number info sourceStephen Warren
This source has been blessed by Dom Cobley at the RPi Foundation, so seems like the best source to refer to. It's a superset of and consistent with the other sources. Cc: Lubomir Rintel <lkundrak@v3.sk> Cc: Eric Anholt <eric@anholt.net> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2016-02-08serial: serial_stm32: move clock config from driver to boardVikas Manocha
This patch removes the uart clock enable from serial driver & move it in the board code. Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08ARM: omap3_logic: Fix pin muxingAdam Ford
Enhance pin muxing to enable more board features and reduce power based on Tony's device tree work. Signed-off-by: Adam Ford <aford173@gmail.com>
2016-02-08Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini
2016-02-06Use correct spelling of "U-Boot"Bin Meng
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-05x86: Drop asm/arch/gpio.hBin Meng
asm/arch/gpio.h is not needed anymore as we get the GPIO base from PCH driver. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-02-04imx: mx6: implement board_mmc_get_env_devPeng Fan
Implement board_mmc_get_env_dev for the boards. Following is examples: SD1/SD2/SD3: return devno; SD2/SD3: return devno - 1; SD2/SD4: if (devno == 2), return dev - 2; return dev - 1; Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-04imx: mx7dsabresd: move mmc_get_env_devno to soc codePeng Fan
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to match the one in common/env_mmc.c. Introduce a weak function board_mmc_get_env_dev. Different boards can implement this according to sdhc controller which is used by the board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-02imx: mx6sxsabresd: Add MCIMX28LCD display supportYe Li
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1 port, enable this display feature by adding relevant BSP codes and configurations. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failureYe Li
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02tqma6_wru4: Fix the reset delay for the the LAN8720 PHYFabio Estevam
According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested by the LAN8720 datasheet. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02mx6slevk: Fix the reset delay for the the LAN8720 PHYFabio Estevam
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested in order to have Ethernet working again. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO boardYe Li
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02arm: imx6: Enable DDR calibration on NovenaMarek Vasut
Enable the DDR calibration functionality on Novena to deal with the memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM parameters so the calibration works properly. Signed-off-by: Marek Vasut <marex@denx.de>
2016-02-02Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-02-02board: atmel: sama5d2_xplained: add SPL supportWenyou Yang
The sama5d2 Xplained SPL supports the boot medias: spi flash and SD Card. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-02arm: at91/spl: mpddrc: add struct atmel_mpddrc_configWenyou Yang
Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-01board: Add Microchip PIC32MZ[DA]-Starter-Kit board.Purna Chandra Mandal
This adds support for Microchip PIC32MZ[DA] StarterKit board based on a PIC32MZ[DA] family of microcontroller. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01malta: Use I/O accessors for SuperI/O controllerPaul Burton
Rather than passing the I/O port base address to the Super I/O code, switch it to using outb such that it makes use of the I/O port base address automatically. Drop the extern keyword to satisfy checkpatch whilst here. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-02-01malta: Set I/O port base earlyPaul Burton
Set the I/O port base earlier, from board_early_init_f, in preparation for it being used by the serial driver. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-01-28Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2016-01-28Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-01-28arm: ls1021atwr: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
generated by cgit (git 2.34.1) at 2024-12-30 23:02:06 +0000