summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2017-09-11armv8: LS2080ARDB: Add secure boot defconfig for QSPI boot.Udit Agarwal
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [YS: dropped redundant commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11LS2080ARDB: QSPI boot: Secure Boot image validationUdit Agarwal
Adds header address for PPA to be validated during ESBC phase for ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It must be initialized before the PPA. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> [YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11fsl-layerscape: Consolidate registers space defination for CCI-400 busAshish Kumar
CoreLink Cache Coherent Interconnect (CCI) provides full cache coherency between two clusters of multi-core CPUs and I/O coherency for devices and I/O masters. This patch add new config option SYS_FSL_HAS_CCI400 and moves existing register space definaton of CCI-400 bus to fsl_immap to be shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET in Kconfig. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> [YS: revised commit message, squashed patches for armv8 and armv7] Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-07ARM: rmobile: Fix SD divider settings on Gen3Marek Vasut
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock must be divided by 4 rather than 2 because a hardware workaround present only in the H3 ES1.0 has been removed from these chips. U-Boot currently only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider to 4 to prevent SD instability. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-07armv8: ls1043/ls1046aqds: add support for RGMII_TXIDMadalin Bucur
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: York Sun <york.sun@nxp.com>
2017-09-05Merge git://git.denx.de/u-boot-rockchipTom Rini
2017-09-05rockchip: phycore: Read configuration EEPROM & set ethaddr in late initWadim Egorov
Read SoM information from EEPROM and set ethaddr in late init. Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-04Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini
2017-09-05ARM: rmobile: Drop board_mmc_initMarek Vasut
The board_mmc_init() is no longer invoked when DM is used, so move all the pinmux config into board_init() instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-05ARM: rmobile: Replace CONFIG_RAVB with CONFIG_RENESAS_RAVB in boardsMarek Vasut
The configuration option name is the later, so replace usage of CONFIG_RAVB in board files with CONFIG_RENESAS_RAVB , otherwise the RAVB pinmux is not set and ethernet does not work. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-03omap3: evm: Fixes for CONFIG_NAND, SPL_OS_BOOT, USB, and environmentDerald D. Woods
- Pass MTDPARTS kernel arguments to kernel - Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND" - Call 'usb_stop' on kernel start - Update Falcon mode setup to match other OMAP3 boards - Use "uEnv.txt" as boot script instead of "boot.scr"
2017-09-01Merge git://git.denx.de/u-boot-sunxiTom Rini
2017-09-01sunxi: Fix CONFIG_SUNXI_GMAC referencesDave Prue
SUNXI_GMAC was still used to configure the code where as the same has been renamed and moved to Kconfig in below commit "sunxi: Move SUNXI_GMAC to Kconfig" (sha1: 4d43d065db3262f9a9918ba72457bf36dfb8e0bb) Signed-off-by: Dave Prue <dave@prue.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Tested-by: Mark Kettenis <kettenis@openbsd.org> [Tweek commit message, config_whitelist.txt, build-whitelist.sh] Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-09-01Merge git://git.denx.de/u-boot-imxTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/imx6qdl_icore_mmc_defconfig configs/imx6qdl_icore_rqs_defconfig
2017-08-30i.MX6Q: icorem6: Add falcon modeJagan Teki
Add Falcon mode support in Engicam i.CoreM6 board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-29pfla02: Fix RAM detection and support 1 bank SOMStefano Babic
In case of 2 banks, the address space of the first CS must be defined and not let to the higher value. Add support for SOM with a single bank of RAM. It was tested with i.MX6Q modules in the following configurations: - 2 Banks, 4 GB - 2 Banks, 1 GB - 1 Bank, 1 GB Signed-off-by: Stefano Babic <sbabic@denx.de>
2017-08-28imx: imx6: Move gpr_init() function to soc.cBreno Lima
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D, MX6Q and MX6QP processors move it to the soc.c file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-26Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini
2017-08-26Merge git://git.denx.de/u-boot-x86Tom Rini
2017-08-26igep00x0: merge igep0020 and igep0030 defconfigs to igep00x0_defconfigPau Pajuelo
Update igep00x0 code with the following features: - Add board and revision detection for the boards: - IGEP0020-RF - IGEP0020-RC - IGEP0030-RG - IGEP0030-RE - Merge IGEP0020 and IGEP0030 mux tables - Add suport to use GPIO_126, GPIO_127 and GPIO_129 - board_name and board_rev environment variables display board and revision informations - Move dtb name selection from code to boot script Signed-off-by: Pau Pajuelo <ppajuel@gmail.com> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Tested-by: Pau Pajuelo <ppajuel@gmail.com>
2017-08-26igep00x0: move SPL routines into separate fileLadislav Michl
Avoid cluttering board file with CONFIG_SPL_BUILD ifdefs by moving SPL related functions into separate file. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Tested-by: Pau Pajuelo <ppajuel@gmail.com> Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2017-08-26board/spear/common: move code to arch/arm/cpu/arm926ejs/spear/Thomas Petazzoni
The code in board/spear/common/ is not board-specific but SoC-specific. Therefore, boards from other vendors than "spear" may want to re-use this code, which is currently difficult with the code being placed in board/spear/common/. Since this code really is SoC-specific, this commit moves it to arch/arm/cpu/arm926ejs/spear/, with the rest of the SPEAr related code. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2017-08-26ARM: rmobile: Remove SH SDHI probing from ULCB boardMarek Vasut
Drop the SH SDHI bit from the board since SD now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26ARM: rmobile: Remove SH SDHI probing from Salvator-X boardMarek Vasut
Drop the SH SDHI bit from the board since SD now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26ARM: rmobile: Remove Serial SH probing from ULCB boardMarek Vasut
Drop the Serial SH bit from the board since UART now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26ARM: rmobile: Remove Serial SH probing from Salvator-X boardMarek Vasut
Drop the Serial SH bit from the board since UART now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26ARM: rmobile: Remove RAVB probing from ULCB boardMarek Vasut
Drop the RAVB bit from the board since RAVB now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26ARM: rmobile: Remove RAVB probing from Salvator-X boardMarek Vasut
Drop the RAVB bit from the board since RAVB now probes from DT instead. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-24x86: dfi-bt700: Select SERIAL_RX_BUFFER via KconfigStefan Roese
To support more input characters (longer stings pasted into the U-Boot prompt) without dropping, lets selects the recently added UART RX buffer for these boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-24x86: conga-qeval20-qa3-e3845: Select SERIAL_RX_BUFFER via KconfigStefan Roese
To support more input characters (longer stings pasted into the U-Boot prompt) without dropping, lets selects the recently added UART RX buffer for these boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-23apalis/colibri_imx6: use independent USB PID for SPLStefan Agner
Use a completely independent USB Product ID for SPL. This allows to differentiate a SDP running in SPL and SDP running in a U-Boot which could not read the config block successfully. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-08-21ARM: mvebu: set correct mem_size for db-88f6820-amcChris Packham
The db-88f6820-amc has four chips with 2Gb density giving a total of 1GB DRAM. Update the board_topology_map to reflect the correct configuration. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2017-08-20ARM: hisilicon: hikey: Fix eMMC with latest ATF & U-BootPeter Griffin
ATF can leave the MMC IP in a state where U-Boot mmc driver can't enumerate the eMMC. This patch provides a mmc0_reset_clk() function like we already so do sd card controller which resets the IP when entering U-Boot. With this patch applied eMMC partitions are successfully enumerated again. => mmc dev 0 switch to partitions #0, OK mmc0(part 0) is current device => mmc part Partition Map for MMC device 0 -- Partition Type: EFI Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000800 0x00000fff "vrl" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 496847ab-56a1-4cd5-a1ad-47f4acf055c9 2 0x00001000 0x000017ff "vrl_backup" attrs: 0x0000000000000000 type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 guid: 61a36fc1-8efb-4899-84d8-b61642efa723 3 0x00001800 0x00001fff "mcuimage" <snip> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
2017-08-18Merge branch 'master' of git://git.denx.de/u-boot-mmcTom Rini
2017-08-18m68k: add board stmark2, mcf5441x basedAngelo Dureghello
Sysam stmark2 board is a generic and fully (hw and sw) open board, with a mcf54415 Coldfire CPU, 128MB of DDR2, 16MB of SPI flash and SD card as non volatile memories, and a wifi module included on-board. The board is actually used mainly for Coldfire custodian testing activity related to the mcf5441x Coldfire family. For further information please see: http://sysam.it/cff_stmark2.html Signed-off-by: Angelo Dureghello <angelo@sysam.it> --- Changes in v2: - remove CMD_REGINFO - add board information in commit message
2017-08-18m68k: mcf5445x: move early ddr init as board-specificAngelo Dureghello
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init is required. This patch moves this ddr/sdram early initalization away from start.S (to be board related). Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2017-08-17dm: imx: cm_fx6: Add MMC support for CONFIG_BLKSimon Glass
When CONFIG_BLK is enabled our weak board_mmc_init() will not be called. Since there is no clock driver for MX6 yet, we must manually enable the clocks. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17dm: imx: cm_fx6: Support driver model for SATASimon Glass
Add support for using driver model for SATA with the cm_fx6 board. The old code remains for now to permit testing. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16Merge git://git.denx.de/u-boot-tegraTom Rini
2017-08-16Merge git://git.denx.de/u-boot-sunxiTom Rini
Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16Merge git://www.denx.de/git/u-boot-imxTom Rini
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16env: Rename some other getenv()-related functionsSimon Glass
We are now using an env_ prefix for environment functions. Rename these other functions as well, for consistency: getenv_vlan() getenv_bootm_size() getenv_bootm_low() getenv_bootm_mapsize() env_get_default() Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()Simon Glass
Rename this function for consistency with env_get(). Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()Simon Glass
We are now using an env_ prefix for environment functions. Rename these for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename getenv/_f() to env_get()Simon Glass
We are now using an env_ prefix for environment functions. Rename these two functions for consistency. Also add function comments in common.h. Quite a few places use getenv() in a condition context, provoking a warning from checkpatch. These are fixed up in this patch also. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()Simon Glass
Rename this function for consistency with env_set(). Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename common functions related to setenv()Simon Glass
We are now using an env_ prefix for environment functions. Rename these commonly used functions, for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename setenv() to env_set()Simon Glass
We are now using an env_ prefix for environment functions. Rename setenv() for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16mx6sabreauto: Fix IOMUXC_GPR6 and IOMUXC_GPR7 valuesBreno Lima
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as commented in the code: /* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F. Signed-off-by: Breno Lima <breno.lima@nxp.com>
2017-08-16mx6sabresd: Fix IOMUXC_GPR6 and IOMUXC_GPR7 valuesBreno Lima
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as commented in the code: /* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F. Signed-off-by: Breno Lima <breno.lima@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-27 15:56:11 +0000