summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2018-06-13ARM: am3517_evm: Enable SPL_OF_CONTROL and SPL_OF_PLATDATAAdam Ford
The SPL doesn't have much room, so in order to support OF_CONTROL in SPL, we need the extra functionality of SPL_OF_PLATDATA. Adding these features allows us to remove a small part of code without losing the serial port during SPL. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-13dra76: fix HDMI HPD pinmuxTomi Valkeinen
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly to all the other DRA7 and AM5 SoCs. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-13dra7/am5: remove CEC pin pull-upTomi Valkeinen
HDMI CEC pins are set to pull-up, but CEC requires no pull. Fix this. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2018-06-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-06-12arm: mvebu: Add Helios4 Armada 38x initial supportDennis Gilmore
The helios4 is built on the SolidRun Armada 38x SOM. The port os based on the ClearFog board, using information from https://github.com/helios-4/u-boot-marvell as well as dtb input from https://github.com/helios-4/linux-marvell Signed-off-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Dennis Gilmore <dgilmore@redhat.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-11board: ls1012a: FRWY-LS1012A board supportBhaskar Upadhaya
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> [yorks: rebase and fix SPDX tag] [yorks: fix board/freescale/ls1012afrdm/Kconfig] Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board: Kconfig: Re-Arrangement of PPA firmware and header addressesBhaskar Upadhaya
PPA firmware and header address may vary depending upon different boards, configure ppa firmware and header address in board specific Kconfig. Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2018-06-07board: samsung: add missing line breaks for pr_err()Seung-Woo Kim
After the commit 9b643e312d52 ("treewide: replace with error() with pr_err()"), there are some pr_err() with no line break. Add missing line breaks. Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2018-06-07mvebu: turris_omnia: add note about i2c slave disableBaruch Siach
Code that disables the i2c slave is now in the mvtwsi i2c driver. Platform must enable DM_I2C to use that code. Add a comment in the code as a reminder for the planned DM_I2C migration of Turris Omnia. Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-06-05ARM: legoev3: update boot script to load uEnv.txt and .dtbDavid Lechner
This updates the LEGO MINDSTORMS EV3 boot script to try loading a uEnv.txt file and a da850-lego-ev3.dtb device tree during boot. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: disable networkingDavid Lechner
This disables networking related items in the config. The EV3 does not have any networking hardware, so this is wasted space. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: Move UART enable to early initDavid Lechner
This moves the UART init for LEGO MINDSTORMS EV3 to board_early_init_f(). Some console messages were not being printed because the UART was not enabled until later in the init process. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: legoev3: increase flash image sizesDavid Lechner
This increases the kernel image to 4M and the rootfs image to 10M. It is getting hard to get a kernel image to fit in 3M. Signed-off-by: David Lechner <david@lechnology.com>
2018-06-05ARM: kirkwood: SBx81LIFKW: Enable network hardwareChris Packham
The SBx81LIFKW boards connect to the internal chassis management network via a Marvell 88e6097 L2 switch. The chassis connections are direct serdes on ports 8 and 9 with a RGMII interface on port 10 connected to the CPU MAC. For debugging purposes ports 0 and 1 are also taken out to headers on the board. Because the debug interfaces are sometimes connected to with straight ribbon cables we need to run them at 10Mbps. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05ARM: add SBx81LIFKW boardChris Packham
This is a series of line cards for Allied Telesis's SBx8100 chassis switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16 and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-05arm: mvebu: switch clearfog to use device-tree i2c and gpioJon Nettleton
This switches the clearfog boards to use DM based gpio and i2c drivers. The io expanders are configured via their device-tree entries. Signed-off-by: Jon Nettleton <jon@solid-run.com> [baruch: add DT i2c aliases] Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-06-04MAINTAINERS: Take over DB410c maintainershipRamon Fried
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-06-04Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2018-06-04board: sun50i: Add Amarula A64-Relic initial supportJagan Teki
Amarula A64-Relic is A64 based IoT device, which support - Allwinner A64 Cortex-A53 - Mali-400MP2 GPU - AXP803 PMIC - 1GB DDR3 RAM - 8GB eMMC - AP6330 Wifi/BLE - MIPI-DSI - CSI: OV5640 sensor - USB OTG - 12V DC power supply Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-06-02Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-06-01Merge tag 'xilinx-for-v2018.07-2' of git://www.denx.de/git/u-boot-microblazeTom Rini
Xilinx changes for v2018.07 second pull zynqmp: - Show reset reason - Remove emulation platform - Update pmufw version - Simplify mmc bootmode - Remove dc2 useless configuration file - Cleanup mini config - Defconfig syncup - zcu100, zcu104 and zcu111 dts fixes xilinx: - Use live-tree functions in some drivers - Add support for Avnet Minized and Antminer S9 fpga: - Add secure bitstream loading support mmc: - Add hs200 mode support usb xhci: - Header fix
2018-06-01Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2018-06-01ARM: renesas: Add R8A77990 E3 Ebisu boardMarek Vasut
Add support for the R8A77990 Ebisu board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-31Merge tag 'arc-updates-for-2018.07-rc1' of git://git.denx.de/u-boot-arcTom Rini
Here we do a couple of minor fixes like: - Move .ivt section to the very beginning of the image by default which allows us to use that image put right at reset vector (usually 0x0) - Improve relocation fix-up which became required once we moved .ivt and understood a problem with existing implementation where we relied on a particular placement of sections. Now we don't care about placement because we just explicitly check for .text and in case of ARCompact .ivt sections - Re-implemnt do_reset() such that it calls reset_cpu() which could implmented for a particular board And hte most important part we introduce support for yet another devboard from Synopsys - EMDK.
2018-05-31ARC: Add support for EM Development Kit boardAlexey Brodkin
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is an FPGA-based development platform from Synopsys aimed to speed-up development of software for ARC EM cores and entire subsystems based on ARC EM like Data Fusion, Secure and Sensor & Control subsystems. U-Boot is supposed to be used as a primary bootloader on EMDK allowing users to easily load and start their application from micro-SD card. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-05-31board: eets: pdu001: Fix wrong default value in KconfigEugeniu Rosca
After importing linux v4.16-rc1 commit 2c37e08464a8 ("kconfig: Warn if choice default is not in choice"), Kconfig complains: scripts/kconfig/conf --syncconfig Kconfig board/eets/pdu001/Kconfig:22:warning: \ choice default symbol 'PDU001_RUN_LED_RED' \ is not contained in the choice This looks to be caused by a typo. Fix it. Fixes: 85ab0452fefc ("arm: add support for PDU001") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Felix Brack <fb@ltec.ch> Tested-by: Felix Brack <fb@ltec.ch>
2018-05-31arm: zynq: Add support for Bitmain Antminer S9 control boardEzequiel Garcia
This is control board on Bitmain Antminer S9. There are 3 board variables with 256MB, 512MB and 1024MB DDR. DDR memory is automatically detected with using get_with using get_ram_size(). Bitmain is using 16MB space for FPGA which is handled via reserved-memory. Also U-Boot is allocating 16B for storing bootcounts. Watchdog is started but never service in U-Boot. SPL MMC is working. SPL NAND is not working because it is not supported as of now. Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-31arm64: zynqmp: Setup the first boot_target at run timeMichal Simek
Detect mmc alias at run time for setting up proper boot_targets sequence. The first target has to correspond with boot mode. The purpose of this patch is to get rid of CONFIG_ZYNQ_SDHCI0/1 parameters in full U-Boot. Unfortunately this patch can't remove it because there is missing mmc implementation for SPL_DM_SEQ_ALIAS. Also xilinx_zynqmp.h only setup boot commands for mmc0 and mmc1. It means using aliases with higher number won't work. But switching between mmc0 and mmc1 should work properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-05-31arm64: zynqmp: Show reset reasonMichal Simek
Read reset reason reg and show it in log and also save it as variable. Clearing reset reason when it is read to show only one status Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-05-30ti: fastboot: Move weak overrides to board filesAlex Kiernan
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c leaves it applying all boards that derive from this, not just the ones which have support for Android bootloader flow. Move the weak function override to the relevant board files. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-30fastboot: Rename fb_set_reboot_flag to fastboot_set_reboot_flagAlex Kiernan
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches all other fastboot code in the global name space. Fix the guards around them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT. Move the weak implementation of fastboot_set_reboot_flag to fb_common.c so we can call it from non-USB fastboot code. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-30fastboot: Move fastboot to drivers/fastbootAlex Kiernan
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-29board: ax25-ae350: Support cfi flashRick Chen
Add smc_init() to get register base from dts and deal with atfsmc020 controler initialzation job. Write protect is enabled by default. So WP shall be disabled when startup, then cfi flash can be detected and erasing and writing can be executed. Adp-ae3xx and adp-ag101p both do smc initilize job in lowlevel_init.S and get register base fron CONFIG_FTSMC020_BASE. They also can be moved those codes to board stage. Remind them as todo jobs. After that CONFIG_FTSMC020_BASE can be removed. Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Cc: Greentime Hu <green.hu@gmail.com>
2018-05-29board: nx25-ae250: Rename as ax25-ae350Rick Chen
Rename nx25 as ax25 ae250 as ae350 nx25-ae250 as ax25-ae350 including filename, variable, string and definition. Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Cc: Greentime Hu <green.hu@gmail.com>
2018-05-28sunxi: Drop legacy usb_phy.cJagan Teki
Allwinner PHY USB code is now part of generic-phy framework, so drop existing legacy handling like arch/arm/mach-sunxi.c and related code areas. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28board: sunxi: Use generic-phy for board_usb_cable_connectedJagan Teki
Allwinner PHY USB code is now part of generic-phy framework, so use it in board_usb_cable_connected. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-26stm32mp1: Allow to activate CONFIG_DEBUG_UARTPatrick Delaunay
Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-05-26ARM: qemu-arm: Bump RAM size in AArch64 MMU tableTuomas Tynkkynen
Now that PCI devices work with highmem-enabled QEMU emulation, bump up the RAM size in the MMU tables to gain access to the full 255 GB of RAM potential instead of the puny 3 GB. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-25tpm: disociate TPMv1.x specific and generic codeMiquel Raynal
There are no changes in this commit but a new organization of the code as follow. * cmd/ directory: > move existing code from cmd/tpm.c in cmd/tpm-common.c > move specific code in cmd/tpm-v1.c > create a specific header file with generic definitions for commands only called cmd/tpm-user-utils.h * lib/ directory: > move existing code from lib/tpm.c in lib/tpm-common.c > move specific code in lib/tpm-v1.c > create a specific header file with generic definitions for the library itself called lib/tpm-utils.h * include/ directory: > move existing code from include/tpm.h in include/tpm-common.h > move specific code in include/tpm-v1.h Code designated as 'common' is compiled if TPM are used. Code designated as 'specific' is compiled only if the right specification has been selected. All files include tpm-common.h. Files in cmd/ include tpm-user-utils.h. Files in lib/ include tpm-utils.h. Depending on the specification, files may include either (not both) tpm-v1.h or tpm-v2.h. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Fix a few more cases of tpm.h -> tpm-v1.h, some Kconfig logic] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-23twister: Let SPL load U-Boot from MMCLadislav Michl
MMC is not initialized in SPL, so it cannot load u-boot.img preventing boot from MMC. Also driver specific functions are guarded with generic configuration options which leads to build failures when device driver is not enabled in config. Fix that by using driver specific defines. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Stefano Babic <sbabic@denx.de>
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-05-20Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2018-05-20ARM: rmobile: Update V2H BlancheMarek Vasut
The V2H Blanche port was broken since some time. This patch updates the V2H Blanche port to use modern frameworks, DM, DT probing, SPL for the preloading and puts it on par with the M2 Porter board. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-18Fixup various SPDX tags from the latest mergeTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-18arm64: zynqmp: Use DWC3 generic driver and DM_USBMichal Simek
Remove harcoded XHCI lists and detect mode, speed based on DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Serial-changes: 2 - Remove also XHCI macros from hardware.h - Remove additional new line in zcu106
2018-05-18arm: imx53: Add support for imx53 boards from K+PLukasz Majewski
This commit adds support for DDC and HSC boards from K+P in u-boot. Console output: U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: WDOG Model: K+P iMX53 DRAM: 512 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial Module EEPROM: ID: TQMa53-CB.0401 SN: 63152762 MAC: 00:0b:64:03:14:2a BBoard:40x0 Rev:10 Net: eth0: ethernet@63fec000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-18configs: imx6dl-mamoj: Add Falcon mode supportJagan Teki
Add Falcon mode support to boot Linux directly after SPL. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
generated by cgit (git 2.34.1) at 2024-12-23 17:26:32 +0000