| Age | Commit message (Collapse) | Author |
|---|
|
Switch to using define for MMC WP GPIO instead of a magic number.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
In the case of Beaglebone Black we only want to set the NAND or NOR cape
pinmux when the config has been specifically modified by the user for
this non-default case. Make the default be to set the MMC1 (eMMC)
pinmux. We don't need similar changes for Beaglebone White as there is
nothing on MMC1 by default there.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
|
|
Separate overo module and expansion board MUX configuration. This allows
an foreign expansion board to use the boot loader without any adaption.
It only needs to save the expansion name in the EEPROM to load a
specific device tree.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
|
|
Move ethernet setup to the board_eth_init function and select
the available network devices via expansion id.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
|
|
This patch adds the DDR3 ECC support to enable ECC in the DDR3
EMIF controller for Keystone II devices.
By default, ECC will only be enabled if RMW is supported in the
DDR EMIF controller. The entire DDR memory will be scrubbed to
zero using an EDMA channel after ECC is enabled and before
u-boot is re-located to DDR memory.
An ecc_test environment variable is added for ECC testing.
If ecc_test is set to 0, a detection of 2-bit error will reset
the device, if ecc_test is set to 1, 2-bit error detection
will not reset the device, user can still boot the kernel to
check the ECC error handling in kernel.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds network support code and enables keystone_net
driver usage for k2e_evm evaluation board.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
For K2E and K2L SoCs clock output from PASS PLL has to be enabled
after NETCP domain and PA module are enabled. So create new function
for that and call it after PA module is enabled.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
Remove unused tx_send_loop variable.
Removes duplicated get_link_status() call from the
keystone2_eth_send_packet().
The emac_gigabit_enable() is called at opening Ethernet and there is no
need to enable it on sending each packet. So remove that call
from keystone2_eth_send_packet() as well.
The calling of power/clock up functions are mostly the responsibility
of SoC/board code, so move these functions to appropriate place.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
This patch adds Keystone II Lammar (K2L) EVM board support.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The initialization of PLLs is a part of board specific code, so
move it appropriate places.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
|
|
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
|
|
One of the possible boot devices can be sata.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
Commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add defines to enable the Chrome OS EC interface and set it up on init.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Use gpio_request for all the gpios that are utilized by various
subsystems in cm-fx6, and refactor the relevant init functions
so that all gpios are requested during board_init(), not during
subsystem init, thus avoiding the need to manage gpio ownership
each time a subsystem is initialized.
The new division of labor is:
During board_init() muxes are setup and gpios are requested.
During subsystem init gpios are toggled.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Since this function can fail, check its return value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add proper initialization of GPIO pins used by software i2c.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Update Apalis T30 as per the following commits
c369139234c03b1494394d12cd27009f47aa6606
tegra: dts: Add serial port details
461be2f96e4b87e5065208c6659a47dd0ad9e9f8
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b62339526df3b921bcfefd174ce76d4c624
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Fix ASIX USB to Ethernet reset which due to the new driver model Tegra
GPIO driver changes now requires a label string to be provided
otherwise the reservation and subsequent direction/value calls will
fail.
This fixes a regression introduced by commit:
2fccd2d96badcdf6165658a99771a4c475586279
tegra: Convert tegra GPIO driver to use driver model
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This pinmux tables currently omit any configuration for PCIe clk_req,
wake, and rst pins, which in turn causes intermittent failures in
U-Boot's PCIe support. Import an updated version of the pinmux tables
which rectifies this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Let HDMI splash screen support work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
|
|
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
|
|
Update readme file for Keystone II EVM boards to actual sources.
Also correct some typos. For now the Edison evaluation board is
added, README for K2E is mostly the same, so update README to
contain information also for K2E evm. Rename file to README as
it contains information for all keystone evm boards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
|
|
The lines COL (collision detect) and CRS (carrier sense) needs to be connected
and muxed to the CPSW MAC for a proper function in half-duplex Mode of the
interface.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Tom Rini <trini@ti.com>
|
|
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
|
|
Fix typo of commit d4e53f063dd25e071444b87303573e7440deeb89.
i2c2 pullup resisters are controlled by bit 0 of CONTROL_PROG_IO1.
It's value after reset is 0x00100001.
In order to clear bit 0, original code write 0xfffffffe to
CONTROL_PROG_IO1 and toggle almost all default values.
Original code affect following:
* disable i2c1 pullup resisters
* increase far end load setting for many modules
* setup invalid SC/LB combination
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Steve Kipisz <s-kipisz2@ti.com>
|
|
These boards have been orphaned for more than 6 months.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
