summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2007-01-13[PATCH] Update Sequoia (440EPx) to display board rev and PCI bus speedStefan Roese
Now the board revision and the current PCI bus speed are printed after the board message. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-06[PATCH] Update ALPR board filesStefan Roese
This update brings the ALPR board support to the newest version. It also fixes a problem with the NAND driver. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-05Merge with /home/stefan/git/u-boot/denx-merge-srStefan Roese
2007-01-05[PATCH] Clear PLB4A0_ACR[WRP] on Sequoia (440EPx)Stefan Roese
This fix will make the MAL burst disabling patch for the Linux EMAC driver obsolete. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-05[PATCH] Add DDR2 optimization code for Sequoia (440EPx) boardStefan Roese
This code will optimize the DDR2 controller setup on a board specific basis. Note: This code doesn't work right now on the NAND booting image for the Sequoia board, since it doesn't fit into the 4kBytes for the SPL image. Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-04Merge with /home/tur/proj/v38b/u-bootWolfgang Denk
2006-12-28Few V38B changes:Bartlomiej Sieka
- fix a typo in V38B config file - move watchdog initialisation earlier in the boot process - add "wdt=off" to default kernel command line (disables kernel watchdog)
2006-12-24Minor code cleanup.Wolfgang Denk
2006-12-24Merge with /home/hs/TQ/u-boot-devWolfgang Denk
2006-12-22[PATCH] Fix sequoia flash autodetection (finally correct)Stefan Roese
Now 32MByte and 64MByte FLASH is know to work and other configurations should work too. Signed-off-by: Stefan Roese <sr@denx.de>
2006-12-22Minor code cleanup; update CHANGELOG.Wolfgang Denk
2006-12-21Added support for the TQM8272 board from TQHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de>
2006-12-20Preliminary support for the iDMR board (ColdFire).Bartlomiej Sieka
2006-12-08automatic update mechanismAndrei Safronov
2006-11-30Code cleanup.Wolfgang Denk
2006-11-30Merge with http://opensource.freescale.com/pub/scm/u-boot-83xx.gitWolfgang Denk
2006-11-30Code cleanup. Update CHANGELOG.Wolfgang Denk
2006-11-29[PATCH] Add support for Prodrive P3M750 & P3M7448 (P3Mx) boardsStefan Roese
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460) and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are quite similar and share the same board directory "prodrive/p3mx" and the same config file "p3mx.h". Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-28Merge http://www.denx.de/git/u-bootKim Phillips
2006-11-28mpc83xx: Miscellaneous code style fixesTimur Tabi
Implement various code style fixes and similar changes. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-28[PATCH] Enable the IceCube/lite5200 variants to pass a device tree to Linux.Stefan Roese
This patch adds the code and configuration necessary to boot with an arch/powerpc Linux kernel. Signed-off-by: Grant Likely <grant.likely@gmail.com> Acked-by: Jon Loeliger <jdl@freescale.com>
2006-11-27Merge with /home/sr/git/u-boot/denx-alpr-merge-testWolfgang Denk
2006-11-27Minor code cleanup. Update CHANGELOG.Wolfgang Denk
2006-11-27[PATCH] alpr: remove unused board specific flash driverStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-27[PATCH] Update Prodrive ALPR board support (440GX)Stefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-27Merge with /home/stefan/git/u-boot/denxStefan Roese
2006-11-23Updates for TQM5200 modules:Wolfgang Denk
- fix off-by-one error in board/tqm5200/cam5200_flash.c error message - simplify "udate" definitions
2006-11-10Merge with /home/stefan/git/u-boot/denxStefan Roese
2006-11-06Sequential accesses to non-existent memory must be synchronized,Wolfgang Denk
at least on G2 cores. This fixes get_ram_size() problems on MPC5200 Rev. B boards.
2006-11-03mpc83xx: Update 83xx to use fsl_i2c.cTimur Tabi
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files. Added multiple I2C bus support to fsl_i2c.c. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03mpc83xx: Replace CFG_IMMRBAR with CFG_IMMRTimur Tabi
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx tree matches the other 8xxx trees. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03mpc83xx: Fix the incorrect dcbz operationDave Liu
The 834x rev1.x silicon has one CPU5 errata. The issue is when the data cache locked with HID0[DLOCK], the dcbz instruction looks like no-op inst. The right behavior of the data cache is when the data cache Locked with HID0[DLOCK], the dcbz instruction allocates new tags in cache. The 834x rev3.0 and later and 8360 have not this bug inside. So, when 834x rev3.0/8360 are working with ECC, the dcbz instruction will corrupt the stack in cache, the processor will checkstop reset. However, the 834x rev1.x can work with ECC with these code, because the sillicon has this cache bug. The dcbz will not corrupt the stack in cache. Really, it is the fault code running on fault sillicon. This patch fix the incorrect dcbz operation. Instead of CPU FP writing to initialise the ECC. CHANGELOG: * Fix the incorrect dcbz operation instead of CPU FP writing to initialise the ECC memory. Otherwise, it will corrupt the stack in cache, The processor will checkstop reset. Signed-off-by: Dave Liu <daveliu@freescale.com>
2006-11-03mpc83xx: add OF_FLAT_TREE bits to 83xx boardsKim Phillips
add ft_pci_setup, OF_CPU, OF_SOC, OF_TBCLK, and STDOUT_PATH configuration bits to mpc8349emds, mpc8349itx, and mpc8360emds board code. redo environment to use bootm with the fdtaddr for booting ARCH=powerpc kernels by default, and provide default fdtaddr values.
2006-11-03mpc83xx: Fix dual I2C support for the MPC8349ITX, MPC8349EMDS, TQM834x, and ↵Timur Tabi
MPC8360EMDS This patch also adds an improved I2C set_speed(), which handles all clock frequencies. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03mpc83xx: add QE ethernet supportDave Liu
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
2006-11-03mpc83xx: Add MPC8360EMDS basic board supportDave Liu
Add support for the Freescale MPC8360EMDS board. Includes DDR, DUART, Local Bus, PCI.
2006-11-03mpc83xx: Fix PCI, USB, bootargs for MPC8349E-mITXTimur Tabi
PREREQUISITE PATCHES: * This patch can only be applied after the following patches have been applied: 1) DNX#2006092142000015 "Add support for the MPC8349E-mITX 1/2" 2) DNX#2006092142000024 "Add support for the MPC8349E-mITX 2/2" CHANGELOG: * For the 8349E-mITX, fix some size values in pci_init_board(), enable the clock for the 2nd USB board (Linux kernel will hang otherwise), and fix the CONFIG_BOOTARGS macro. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03mpc83xx: Add support for the MPC8349E-mITXTimur Tabi
PREREQUISITE PATCHES: * This patch can only be applied after the following patches have been applied: 1) DNX#2006090742000024 "Add support for multiple I2C buses" 2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x" 3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c" 4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems" 5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems" CHANGELOG: * Add support for the Freescale MPC8349E-mITX reference design platform. The second TSEC (Vitesse 7385 switch) is not supported at this time. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03Additional MPC8349 support for multibus i2cBen Warren
Hello, Here is a patch for a file that was accidentally left out of a previous attempt. It accompanies the patch with ticket DNX#2006090742000024 CHANGELOG: Change PCI initialization to use new multi-bus I2C API. regards, Ben
2006-11-03mpc83xx: Unified TQM834x variable names with 83xx and consolidated macrosTanya Jiang
Unified TQM834x variable names with 83xx and consolidated macro in preparation for the 8360 and other upcoming 83xx devices. Signed-off-by: Tanya Jiang <tanya.jiang@freescale.com>
2006-11-03mpc83xx: Changed to unified mpx83xx names and added common 83xx changesDave Liu
Incorporated the common unified variable names and the changes in preparation for releasing mpc8360 patches. Signed-off-by: Dave Liu <daveliu@freescale.com>
2006-11-03mpc83xx: Fix missing build for mpc8349emds pci.cTanya Jiang
Make pci build for mpc8349emds Signed-off-by: Tanya Jiang <tanya.jiang@freescale.com>
2006-11-01Finish up support for MarelV38B boardBartlomiej Sieka
- add watchdog support - enable GPIO_WKUP_7 pin for input - code cleanup
2006-11-01- Fix issues related to the use of ELDK 4 when compiling for MarelV38B:Bartlomiej Sieka
* remove warnings when compiling ethaddr.c * adjust linker script (fixes a crash resulting from incorrect definition of __u_boot_cmd_start) - Some MarelV38B code cleanup.
2006-11-01- Add MPC5XXX register definition MPC5XXX_WU_GPIO_DATA_I and change theBartlomiej Sieka
MPC5XXX_WU_GPIO_DATA macro to MPC5XXX_WU_GPIO_DATA_O (per MPC5200 User's Manual). Replace the uses of MPC5XXX_WU_GPIO_DATA with MPC5XXX_WU_GPIO_DATA_O for affected boards. - Add defintions for some MPC5XXX GPIO pins.
2006-10-28[PATCH] Add some missing machtypes for netstar & voiceblue boardsStefan Roese
Use MACH_TYPE_NETSTAR and MACH_TYPE_VOICEBLUE defines instead of numbers in code. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Stefan Roese <sr@denx.de>
2006-10-27Fix "ar" flags in some Makefiles to allow for silent "make -s"Wolfgang Denk
2006-10-25Finish up support for the ATSTK1000/ATSTK1002 boardsHaavard Skinnemoen
Add atstk1002_config target to Makefile and move the AVR32 section down below Blackfin so that it doesn't end up in the middle of MIPS. Drop the autogenerated linker script thing for now. Will have to revisit how to handle chips with different flash and RAM layout later. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-10-24Merge with /home/wd/git/u-boot/masterWolfgang Denk
2006-10-24Merge with /home/wd/git/u-boot/mailing-list/Haavard_SkinnemoenWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-29 10:15:46 +0000