| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
Patch by Martin Krause, 20 Mar 2006
Signed-off-by: Martin Krause <martin.krause@tqs.de>
|
|
Patch by Markus Klotzbuecher, 12 Jul 2006
|
|
|
|
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
Patch from Richard Danter, 12 Aug 2005
|
|
|
|
Patch by Thomas Lange, Aug 11 2005
|
|
Patch by Thomas Waehner, 07 Mar 2006
|
|
Patch by Martin Krause, 11 Jan 2006
|
|
Patch by Martin Krause, 07 Nov 2005
Tested on a STK85XX baseboard. Make sure the PS/2 controller
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
|
|
Patch by Martin Krause, 08 Nov 2005
In tsc2000_read_channel() the delay after setting the multiplexer
to a temperature channel is increased from 1,5 ms to 10 ms. This
is to allow the multiplexer inputs to stabilize after huge steps
of the input signal level.
|
|
Make the automatic CS configuration the default.
The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
and CONFIG_TQM5200_AC are removed.
"TQM5200_config" is now the default for STK52XX.200 base boards.
On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
Patch by Martin Krause, 07 Nov 2005
|
|
The environment variable "ver" is now set before
do_auto_update() is called, so that "ver" can be used
in USB update scripts.
Patch by Martin Krause, 27 Oct 2005
|
|
Patch by Martin Krause, 27 Oct 2005
|
|
Patch by Martin Krause, 27 Oct 2005
|
|
|
|
|
|
|
|
|
|
|
|
Patch by Scott McNutt, 08 Jun 2006
|
|
-Update base addresses for standard configuration
-Eliminate use of CACHE_BYPASS in board code
Patch by Scott McNutt, 08 Jun 2006
|
|
|
|
Signed-off-by: Jon Loeliger <jdl@jdl.com>
|
|
|
|
|
|
|
|
Patch by Stefan Roese, 06 Jun 2006
|
|
|
|
Patch by Stefan Roese, 02 Jun 2006
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Some 80-column cleanups.
Convert printf() to puts() where possible.
Use #include "spd_sdram.h" as needed.
Enhanced reset command usage message a bit.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
First cut at moving the PIXIS platform code out of
the 86xx cpu directory and into board/mpc8641hpcn
where it belongs.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Patch by Stefan Roese, 29 May 2006
|
|
- Add IXP4xx NPE ethernet MAC support
- Add support for Intel IXDPG425 board
- Add support for Prodrive PDNB3 board
- Add IRQ support
Patch by Stefan Roese, 23 May 2006
[This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still
sufferes from licensing issues. Blame Intel.]
|
