| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Conflicts:
arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Synology keeps per item configuration in a dedicated 'partition' in SPI
flash, namely the one named 'vendor' in DTS file. It contains the two
NICs MAC addresses as well as the item's serial number. I didn't find a
way to have this information extracted automatically, therefore
implemented 'syno populate_env' command which extracts the three values
and puts them into environment. To make things permanent though, one has
to 'saveenv'.
Another command is 'syno clk_gate', which allows to change the clock
gating which is done in DS414 board file.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Merging all the board specific Kconfig options into the main Kconfig file
for mach-mvebu makes things easier to maintain.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
|
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
|
|
This cleans up the mux configuration a bit, setting mmc clock signals to input
enabled and specifying pull-down (0) when pull is not used.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Do not set HAVE_INTEL_ME by default as for some cases Intel ME
firmware even does not reside on the same SPI flash as U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Update my email address to the NXP account.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
|
|
'sf command' should receive the length in sector boundaries, so fix it
accordingly.
Also, show the steps to set the server and board IP addresses for
making the steps clearer.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
We currently support various versions of Solidrun mx6 boards, so
remove the obsolete comment.
Reported-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional:
Booting from net ...
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
As per the AR8035 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and keep the reset low for 10ms.
Also add a 100us delay after deasserting the reset line
to guarantee that the PHY ID can be read correctly and the Atheros
PHY can be loaded as per Troy Kisky's suggestion.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Change from yorksun@freescale.com to york.sun@nxp.com.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
According to the Coverity result, a unsigned int variable is used fo less-
than-zero comparison, the result is never true. Need to fix the variable
type to signed int.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
As per the AR8031 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.
This results in a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
As per the AR8031 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.
This results in a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In pci_map_region(), pass 'range_id' to fdt_read_range(),
otherwise the same address will be mapped again in other
calls to pci_map_region()
Signed-off-by: Miao Yan <yammiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
|
|
|
|
Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.
ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().
Signed-off-by: Michael Schanz <michael.schanz@congatec.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Conflicts:
include/configs/axs101.h
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Updated pinmux group GENERALIO[15-16] for i2c.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: shengjiangwu <shengjiangwu@icloud.com>
|
|
Updated pinmux group EMACIO[1-8] and EMACIO[10-13] for USB.
Signed-off-by: shengjiangwu <shengjiangwu@icloud.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Updated pinmux group MIXED1IO[15-20] for QSPI.
Updated QSPI clock.
Signed-off-by: shengjiangwu <shengjiangwu@icloud.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
Updated pinmux group MIXED1IO[0-13] for RGMII1.
Updated EMAC1 clock.
Signed-off-by: shengjiangwu <shengjiangwu@icloud.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
|
|
This symbol is not used anywhere, so remove it. For spear600, remove
it from the board file, since the symbol is not defined for spear600
either.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Drop all the common board code, since it is not completely useless.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
|
|
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
|
|
watchdog and gpio are not validated for SPL that's why do not use them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
LL_TEMAC is available at big endian MB and it is not properly tested
that's why the patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.
Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
