summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2018-10-09colibri_imx7: prime get_ram_size() using imx_ddr_size()Fabio Estevam
Rather than passing a hardcoded maxsize to the generic get_ram_size() function use the i.MX 7 specific imx_ddr_size() function, which extracts the memory size at runtime by reading the DDR controller registers. This is a purely cosmetic change as the generic get_ram_size() function already took care of properly automatically detecting 256MB, 512MB or 1GB modules. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Stefan Agner <stefan.agner@toradex.com>
2018-10-09pico-imx7d: Add USB Host supportFabio Estevam
USB OTG2 port is connected to the USB host connector. Add support for it. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-10-06ARM: LogicPD: omap3logic: Remove Torpedo/SOM-LV autodectionAdam Ford
With there now being four device tree files, and 4 separate defconfig files, the code necessary to determine which board is being used is no longer necessary as the corresponding pin-muxing and board names are determined by the device tree. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-06ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV and OMAP35 TorpedoAdam Ford
With the device trees doing most of the work of pin-muxing and DM doing much of the peripheral initialization, this creates new defconfig files for each of the Logic PD variants with proper register settings/pin-muxing. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update MAINTAINERS entry] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-05arc: Add support for IoT development kitAlexey Brodkin
The DesignWare ARC IoT Development Kit is a versatile platform that includes the necessary hardware and software to accelerate software development and debugging of sensor fusion, voice recognition and face detection designs. More information is avaialble here [1] and here [2]. The board is based on real silicon with ARC EM9D-based Data Fusion IP Subsystem. It sports a rich set of I/O including * DW USB OTG * DW MobileStorage (used for micro SD-card) * GPIO * multiple serial interface including DW APB UART * ADC, PWM and eFlash, SRAM and SPI Flash memory * Real-Time Clock (RTC) * Bluetooth module with worldwide regulatory compliance (FCC, IC, CE, ETSI, TELEC) * On-board 9-axis sensor (gyro, accelerometer and compass) Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18 extension header. One of the most interesting features for developers is built-in Digilent USB JTAG probe so only micro-USB cable is needed! [1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit [2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-10-03riscv: Add QEMU virt board supportBin Meng
This adds QEMU RISC-V 'virt' board target support, with the hope of helping people easily test U-Boot on RISC-V. The QEMU virt machine models a generic RISC-V virtual machine with support for the VirtIO standard networking and block storage devices. It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and it also uses device-tree to pass configuration information to guest software. It implements RISC-V privileged architecture spec v1.10. Both 32-bit and 64-bit builds are supported. Support is pretty much preliminary, only booting to U-Boot shell with the UART driver on a single core. Booting Linux is not supported yet. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2018-10-03riscv: Remove mach typeBin Meng
Since the mach_id is not used by RISC-V, remove it. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
2018-10-01MAINTAINERS: at91: update entry for at91 boardsEugen Hristev
Updated the maintainership for the at91 boards. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-30Merge git://git.denx.de/u-boot-dmTom Rini
2018-09-30MAINTAINERS: Update some entries for missed boardsTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-30db410c: automatically launch fastbootRamon Fried
If during boot the key-vol-down press is detected we'll fall back to fastboot. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30db410c: serial# env using msm board serialRamon Fried
The serial# environment variable needs to be defined so it will be used by fastboot as serial for the endpoint descriptor. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30ehci: Replace board_prepare_usb with board_usb_initRamon Fried
Use standard board_usb_init() instead of the specific board_prepare_usb. Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-29Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-29sandbox: Add an explanation of the sandbox variantsSimon Glass
There are quite a few builds of sandbox now. Add information about these to the README. Signed-off-by: Simon Glass <sjg@chromium.org>
2018-09-29Merge tag 'mpc85xx-for-v2018.11-rc1' of git://git.denx.de/u-boot-mpc85xxTom Rini
Use device tree for mpc85xx with binman. Enabled for T2080QDS.
2018-09-29Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A, LS1043A, LS1046A, LS1088A, LS2088A. Switch to driver model for SATA on LS1021A and LS1043A. Add support for LS1012AFRWY rev C board. Enable SMMU for LS1043A.
2018-09-29ARM: omap3_logic: Remove non-DM MMC initializationAdam Ford
With DM_MMC working for both SPL and U-Boot, this patch removes the legacy style of initializing the MMC driver. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29ARM: omap3_logic: Remove some manual pin-muxingAdam Ford
With the pinctrl function enabled and the device tree setting up the pins we want to use, this patch removes the manual pinmuxing except for that which is not done by the device tree and minimal pins necessary for SPL (like serial, GPMC, and MMC) Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-28board: sama5d4_xplained: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d2_ptc_ek: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d27_som1_ek: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d3_xplained: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: sama5d2_xplained: add pda detect call at init timeEugen Hristev
Call the PDA detection mechanism at boot time so we can have the pda environment variable ready for use. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28board: atmel: add support for pda detectionEugen Hristev
This adds the support for PDA detection as common code for Atmel boards. Using the one wire interface over GPIO , an EEPROM memory is read and compared to preprogrammed values for PDA screens TM4300, TM7000 and TM7000B. Once the PDA is detected, an environment variable is set accordingly. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28cmd: Add osd commandsMario Six
Add command to query information from and write text to on-screen display (OSD) devices. Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-27powerpc: dts: Enable device tree support for T2080QDSJagdish Gediya
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL so that device tree can be compiled. Update board README for device tree usage. Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv8: ls1043a: add icid setup supportLaurentiu Tudor
Reuse the existing ICID setup code done for LS1046A smmu enablement and add the equivalent setup for LS1043A chips. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27u-boot: fixup the iommu-map property of fsl-mc nodeNipun Gupta
The iommu-map property in the fsl-mc node is updated by valid stream-ids by u-boot. This patch is to fixup this property for LS208x and LS1088. Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27ls1012afrwy: Add ls1012afrwy revC board support.Pramod Kumar
LS1012AFRWY supports three board revisions. Revision A and B board are collectively identified as revA/B, Revision C board is identifies as revC. Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> [York S: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27armv7: fsl: remove sata supportPeng Ma
Remove the old implementation in order to enable DM for sata Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-27Merge tag 'xilinx-for-v2018.11' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.11 - Handle BOARD_LATE_INIT via Kconfig SPL: - Enable GZIP for all partitions types(not only for kernel) ZynqMP: - Rearrange pmufw version handling - Support newer PMUFW with improved fpga load sequence Zynq: - Cleanup config file - Simplify zybo config by enabling option via Kconfig net: - Fix gems max-speed property reading - Enable support for fixed-link phys
2018-09-26arm64: zynqmp: Return pmufw version for zynqmp_pmufw_version()Siva Durga Prasad Paladugu
Modify the zynqmp_pmufw_version() routine to return PMUFW version so that it can be reused wherever required. Get PMUFW version from PMU only once at bootup and later just return stored value. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-25board: ti: am335x: add support to fixup phy addressSekhar Nori
On beaglebone black, it can so happen that PHY address is not latched correctly on reset and board boots with PHY responding to a different address than that programmed in device-tree. For example, see this report: https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J Workaround this by fixing up device-tree passed to kernel by using the PHY address detected in hardware. Beaglebone itself uses only one ethernet port and its DT currently uses phy_id (obsoleted). But the function has been written to handle multiple ports and phy_id as well as phy-handle to make the function more generically useful. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-09-25board: st: stm32mp1: Add usb gadget supportPatrice Chotard
Enable USB gadget support using DWC2 driver Populate board_usb_init() to initialize clocks, phy, reset and data needed for DWC2 IP. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-23mips: Add Gardena Smart-Gateway board supportStefan Roese
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage. This patch also includes 2 targets. One is the target that can be programmed into the SPI NOR flash and a 2nd target "xxx-ram" is added to support loading and booting via an already running U-Boot version. This allows easy development and testing without the need to flash the image each time. Signed-off-by: Stefan Roese <sr@denx.de> [fixed and regenerated defconfig files] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-09-23mips: Add LinkIt Smart 7688 supportStefan Roese
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM and 32 MiB of flash (SPI NOR). This patch also includes 2 targets. One is the target that can be programmed into the SPI NOR flash and a 2nd target "xxx-ram" is added to support loading and booting via an already running U-Boot version. This allows easy development and testing without the need to flash the image each time. Signed-off-by: Stefan Roese <sr@denx.de> [fixed and regenerated defconfig files] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-09-19Merge git://git.denx.de/u-boot-imxTom Rini
- changes in pico-* boards - fix imx6ull pinmux
2018-09-19board: turris_mox: Fixup U-Boot's device tree if PCIe connectedMarek Behún
If PCIe Mox module is connected we want to have PCIe node enabled in U-Boot's device tree. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19board: turris_mox: Fix watchdog macro nameMarek Behún
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX instead. Fix this so that watchdog really is enabled in board_init. Signed-off-by: Marek Behun <marek.behun@nic.cz> Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-18pico-imx7d: Add a new defconfig with PICO-Hobbit selectedOtavio Salvador
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard allowing a completely non-interactive boot process. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-18pico-imx7d: Fix TechNexion spelling on MAINTAINERS fileOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-18pico-imx6ul: Add a new defconfig with PICO-Pi selectedOtavio Salvador
This adds a new defconfig which pre-selects the PICO-Pi baseboard allowing a completely non-interactive boot process. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-18pico-imx6ul: Fix TechNexion spelling on MAINTAINERS fileOtavio Salvador
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-18Merge branch 'master' of git://git.denx.de/u-boot into masterStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2018-09-15sh: sh7723: ap325rxa: Drop duplicate HIZCRB macroMarek Vasut
Drop the macro as it is defined in sh7723.h already. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-09-14pico-imx6ul: Add instructions for booting in Falcon modeFabio Estevam
Falcon mode allows the SPL to load and jump directly to the kernel, without loading U-Boot proper. Add detailed step by step on how to use Falcon mode on pico-imx6ul. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14pico-imx6ul: Add Falcon mode supportOtavio Salvador
Falcon mode boots the kernel directly from SPL, without loading the full U-Boot. As pico-imx6ul does not have a GPIO for selecting Falcon versus normal mode, enter in Falcon mode when the customer selects the CONFIG_SPL_OS_BOOT option in menuconfig. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-09-14wandboard: README: Include the mx6qp variant in the listFabio Estevam
The mx6qp Wandboard variant is also supported, so add it to the list. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-09-14ARM: bootscript: For nfsargs only use rootpath (and remove not needed serverip)Lukasz Majewski
The serverip part is provided from DHCP server with 'option root-path "192.168.3.1:/srv/tftp/rootfs";' parameter in dhcpd.conf Signed-off-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-26 02:37:17 +0000