| Age | Commit message (Collapse) | Author |
|---|
|
Currently during init, we enable all power, then enable the dram and
after that check whether there was an error during power-up.
This makes little sense, we should enable power and then check if power
was brought up properly before we continue to initialize other things.
This patch moves the DRAM init after the power failure check.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add an entry for the Ficus EE board to the existing rock960 MAINTAINERS
file.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
|
|
- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
|
|
This patch adds S-mode defconfigs for QEMU virt machine so
that we can run u-boot in S-mode on QEMU using M-mode runtime
firmware (BBL or equivalent).
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
When u-boot runs in S-mode, the M-mode runtime firmware
(BBL or equivalent) uses memory range in 0x80000000 to
0x80200000. Due to this, we cannot use 0x80000000 as
SYS_TEXT_BASE when running in S-mode. Instead for S-mode,
we use 0x80200000 as SYS_TEXT_BASE.
Even Linux RISC-V kernel ignores/reserves memory range
0x80000000 to 0x80200000 because it runs in S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
|
|
Bundle DTBs for R8A7795, R8A7796 ULCB variants into single U-Boot
build and let U-Boot choose between them based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Drop unused MSTP macros from Gen3 boards. These are no longer needed
as the boards are using clock framework to manipulate clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Update email address
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
|
|
Xilinx changes for v2019.01
microblaze:
- Use default functions for memory decoding
- Showing model from DT
zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets
zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting
nand:
- arasan: Add subpage configuration
net:
- gem: Add 64bit DMA support
|
|
Patch queue for rpi - 2018-12-03
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
|
|
Add Raspberry Pi 3 Model A+ to list of models, the revision code is 0xE
according to the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Replace various third party lists of Raspberry Pi revision codes in a
comment with the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch switches MCR3000 board to the new DM watchdog.
The change in u-boot.lds is because MCR3000.o grows a bit
with this patch and doesn't fit anymore below env_offset on
some versions of GCC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
Add mcr3000 device tree and activate CONFIG_DM and CONFIG_OF_CONTROL
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
OnRISC Baltos series uses SoM with tps65910 PMIC, so remove
"power/tps65217.h" header inclusion.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This allows us to print nice board name on boot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Instead of "base + offset" define all registers right away
and access them later via direct defines.
Generate bit masks with "BIT" macro.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
We do real CPU clock measurement with help of built-in
counters. Thus we may accommodate different real clock values
that appear in different FPA images instead of relying on
something hard-coded in the .dtb.
And while at it make make SDIO base address define
look similar to others with casting to "(void *)".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Since we now do advanced CPU identification in
generic ARC code there's no need to have per-board
hardcoded data.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
Fix sound on sandbox
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
|
|
Some factory data is stored in the SPI NOR and needs to get extracted
from there into U-Boot environment variables.
This patch also includes a board-specific command "fd_write" to
provide some dummy / default values for this factory-data in the SPI
NOR flash. This should only be necessary for testing purposes though.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
For testing purpose use zcu102 which has SD at controller 1 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00279-gdc482e7ee092 (Nov 30 2018 - 10:22:56 +0100)
Model: ZynqMP MINI EMMC1
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff170000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100)
Model: ZynqMP MINI EMMC0
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff160000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If only usb ethernet gadget is enabled it can start automatically.
If more gagdets are enabled usb ethernet gadget can be bind by
"bind /amba/usb1@ff9e0000/dwc3@fe300000 usb_ether" (on zcu100)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add meson meson compatibles
- Amlogic Meson cleanup for AXG SoC support
|
|
At present many TPM calls assume there is only one TPM in the system and
look up this TPM themselves. This is inconsistent with driver model, which
expects all driver methods to have a device parameter. Update the code to
correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Wire up mini_qspi SPL with zcu102 for testing purpose.
Normally mini u-boot runs with FSBL/SPL for certain board.
Enabling SPL and configuration from zcu102 helps with testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
These symlinks are here only for testing purpose where SPL is used
for soc configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This adds a general board file based on MT7623 SoCs from MediaTek.
As this u-boot is loaded by MTK proprietary preloader, there is no
low level initializtion codes.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related
code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
DM_SERIAL is selected by TARGET_CHILIBOARD, so there is no reason to
keep code that will not be built. Remove it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove ethernet platform data, as all
details are in device-tree now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() functions to
weak functions into the board-common mach-meson file.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The S400 board is the Amlogic AXG SoC reference board including :
- Amlogic A113DX ARM Cortex-A53 quad-core SoC @ 1.2GHz
- 1GB DDR4 SDRAM
- 10/100 Ethernet
- 2 x USB 2.0 Host
- eMMC
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connectors
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a SoC architecture and add a custom config header or custom
board handler for a platform.
This drops the board CONFIGs and the duplicate boards configs headers in
favor of a single meson64.h config header.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. Dedicated defconfig are kept to customize
the names and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The Khadas vim2 derive from amlogic s912 reference design (Q200).
This patch moves the khadas-vim2 board support to a generic Q200 board,
while keeping a dedicated defconfig to customize the names and device tree.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).
All the code in these board is a copy/paste from the p212, which is
tedious to maintain. This change use p212 u-boot board for all these
boards, while keeping a dedicated defconfig to customize the names
and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
We have a few things in the memory map now, so add documentation for this
to avoid confusion. Also note that it is possible to run all tests now.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The standard function is less error prone than custom one.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If SYS_LONGHELP is disabled the following warning is generated:
board/xilinx/zynq/cmds.c:496:13: warning: ‘zynq_help_text’ defined but
not used [-Wunused-variable]
Normal way for fixing this is to guard the whole variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The VCU disable bit(8) in IP disable register of efuse
is valid only if PL powered up and hence PL powerup status
has to be considered while determining the CG part also.
This patch considers the PL powerup status and ignores the VCU
disable bit if PL not powered up.
This fixes the issue of "unknown" id for CG parts if PL not powered up
and VCU bit(8) is not set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
