summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2020-04-06arm64: zynqmp: Move timeout for clock propagation below psu_initMichal Simek
Delay required for clock propagation is tighly coupled with initialization done in psu_init(). That's why call it also for u-boot proper with CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: zynqmp: Add support for debug uart also for U-Boot properMichal Simek
board_early_init_f() is the right location where debug uart can be configurated (after MIO initialization). The patch is taking this call from SPL to also make it available for U-Boot proper. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: zynqmp Add support for zcu111 revAMichal Simek
Add low level configuration for zcu111 for easier SPL run. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: zynqmp Add support for zcu102 rev1.1Michal Simek
rev1.1 has different DDR sodimm module that's why it requires different DDR configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: zynqmp: Check firmware node when driver is enabledMichal Simek
ZynqMP mini configurations works without PMU firmware that's why there is no reason to enable the driver and check if it was probed properly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: zynqmp: Print multiboot register value in EL3Michal Simek
Multi boot register can be used for using different boot images and design better boot strategy. Let EL3 SPL or U-Boot to read it and print it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-02ARM: tegra: Add NVIDIA Jetson Nano Developer Kit supportTom Warren
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage. HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K). A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-04-02t210: pinmux: Remove pinmux/GPIO init from T210 boardsTom Warren
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB tables. Remove pinmux/GPIO init tables & code from all T210-based builds below: p2371-2180 aka TX1 p2371-0000 e2220-1170 p2571 Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2020-04-01Merge tag 'u-boot-stm32-20200401' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Fix device tree of Avenger96 board from Arrow Electronics and add compatibility with stm32mp15_dhcom_basic_defconfig
2020-04-01ARM: dts: stm32: Use DT alias for the configuration EEPROMMarek Vasut
Use DT /aliases node to establish a stable phandle to the configuration EEPROM. This permits the configuration EEPROM to be moved e.g. to a different address or a different bus. Adjust the board code to handle new phandle lookup. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-03-31Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- Fixes for Gen 2 V2H Blanche
2020-03-30ARM: rmobile: Only register ethernet on V2H Blanche if not DM_ETHMarek Vasut
If the DM_ETH is enabled, the board-specific ethernet registeration should be disabled, make it so. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-30ARM: rmobile: Implement PMIC reset on V2H BlancheMarek Vasut
Add code to reset the board through PMIC, by writing the required PMIC registers in the CPU reset handler. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-30configs: ls1012ardb: secure boot: Add PFE configPriyanka Singh
Add config to enable the PFE and ETH support. Also change the pfe secure boot header address. Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30dm: arm64: ls1046a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1046A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30dm: arm64: ls1043a: add i2c DM supportBiwen Li
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1043A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: fsl: lx2160a: fix SDHC1_DAT4 signal routingYangbo Lu
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1 adapter slot for SDHC1 usage. When SDHC1 is selected in RCW, do not force to route it to SDHC1 adapter slot if find it has already been configued for SDHC1_VS. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30lx2160a : Remove default VID settingMeenakshi Aggarwal
Set VID to 800 mV for Rev1 and set VID as per switch settings for Rev2. Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: fsl: lx2160a: Add GIC LPI memory reserve fixupWasim Khan
Reserve DDR memory region used for GIC LPI configuration table. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: fsl: lx2160a: Program GIC LPI configuration tableWasim Khan
Program GIC LPI configuration table: 1. Redistributor PROCBASER configuration table (which is common for all redistributors) 2. Redistributor pending table (PENDBASER), for all the available redistributors. Signed-off-by: Manish Tomar <manish.tomar@nxp.com> Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30board: lx2160a: Correct board fixup for PCIe nodesVikas Singh
Update "board_fix_fdt" with correct counter value "i". This will fix the issue while fetching the "reg_names" resource from fdt after fixup. Signed-off-by: Vikas Singh <vikas.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-26elgin-rv1108: Use rk_board_late_init() for GPIO settingsOtavio Salvador
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f for per-boar init") the function that configure the board GPIOs is no longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected. These GPIOs do not need to be configured in such early stagem, so change it to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y to fix the regression. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26rockchip: evb-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-03-26rockchip: elgin-rv1108: Use syscon API to get grf baseKever Yang
Use syscon API to get grf base instead of get from dts. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2020-03-10mx6slevk: Convert to DM_ETHPedro Jardim
This fixes the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-10mx6sabreauto: Convert to DM_ETHPedro Jardim
This fixes the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-10arm: dts: imx8mq-evk: add phy-reset-gpios for fec1Alifer Moraes
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the driver reset the phy via dts description adding a reset duration of 10 ms following atheros 8031's datasheet recommendation. Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
2020-03-10mx6sabresd: Convert ethernet to driver modelAlifer Moraes
Convert imx6sabresd ethernet to driver model to fix the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-09imx8qxp_mek: Add myself as maintainerFabio Estevam
I would like to help co-maintaining this board. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09mx7dsabresd: Add myself as maintainerFabio Estevam
I would like to help co-maintaining this board. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09imx: remove woodburn boardStefano Babic
Board is not longer used, remove it. Signed-off-by: Stefano Babic <sbabic@denx.de>
2020-03-09imx6, aristainetos2c: add da9063 pmic setupHeiko Schocher
On the aristainetos2c boards the PMIC needs to be initialized, because the Ethernet PHY uses a different regulator that is not setup per hardware default. This does not influence the other versions as this regulator isn't used there at all. Signed-off-by: Heiko Schocher <hs@denx.de>
2020-03-05toradex: MAINTAINERS: entries for new reST docsIgor Opaniuk
Add entries for the newly created documentation files in reST format. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-03-05doc: board: colibri-imx8x: convert readme to reSTIgor Opaniuk
Convert README to reStructuredText format. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-03-05doc: board: apalis-imx8: convert readme to reSTIgor Opaniuk
Convert README to reStructuredText format. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2020-03-05doc: board: verdin-imx8mm: convert readme to reSTIgor Opaniuk
Convert README to reStructuredText format. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: spell out U-Boot correctly] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2020-03-04Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
- ABB SECU board - Assorted minor fixes
2020-03-03ARM: socfpga: Add initial support for the ABB SECU boardHolger Brunck
Add initial support for the ABB SECU board, which is an ArriaV-based SoCFPGA system with ethernet and booting from Denali NAND. Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2020-03-02Merge tag 'u-boot-stm32-20200203' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - convert stm32mp1 board documentation to rst format
2020-03-02doc: add board documentation for stm32mp1Patrick Delaunay
Change plain test README to rst format and move this file in documentation directory. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-28ARM: zynq: Rename defconfig to be align with ZynqMP and VersalMichal Simek
Just cosmetic change before real switch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-28arm: xilinx: Fill DEVICE_TREE directly in MakefilesMichal Simek
DEVICE_TREE variable is not exported from dts/Makefile that's why it is necessary to setup directly before use. Fixes: 312f2c5b14fa ("arm: xilinx: Use device tree which can be passed on cmd line") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-28arm: zynq: zybo z7: fix MIO init issueMilan Obuch
The board has two push button connected to MIO pins 50 and 51, which have a pull-down resistor and are connected to 1.8V when pressed. These two pins are wrongly initialized with internal pull-up enabled so they are reported as 1 all the time with no change when pressed. Disable the internal pull-up to fix the issue. Signed-off-by: Milan Obuch <u-boot@dino.sk> Signed-off-by: Luis Araneda <luaraneda@gmail.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-19board: roc-pc-rk3399: Add support for onboard LED's and push button to ↵Suniel Mahesh
indicate power mode Added support for onboard LED's and push button. When powered board will be in low power mode(yellow LED), on button press, board enters full power mode (red LED) and boots u-boot. Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-19rockchip: rk3399: split roc-pc-rk3399 out of evb_rk3399Suniel Mahesh
roc-pc-rk3399 board has one user button & three user LED's. Currently we don't have any code support for these devices. Since button and LED's are specific to roc-pc-rk3399 board, split it into its own board file and add code support here. Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-02-14Merge tag 'u-boot-stm32-20200214' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - add DH Electronics DHCOM SoM and PDK2 board - DT alignment with kernel v5.5-rc7 for stm32mp1 boards - fix STM32 image format for big endian hosts in mkimage - solve warnings in device tree and code for stm32mp1 boards - remove fdt_high and initrd_high for stm32 and stih boards - add support of STM32MP15x Rev.Z - update stm32mp1 readme
2020-02-13board: stm32mp1: change dfu function to staticPatrick Delaunay
Change the dfu functions dfu_otp_read and dfu_pmic_read to static, this patch avoids warning when compiling with W=1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13board: stm32mp1: board: add include for dfuPatrick Delaunay
Add include for dfu, add prototype for set_dfu_alt_info and avoid warning when compiling with W=1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13board: stm32mp1: update readmePatrick Delaunay
Update readme: - list the supported SOC and change family to STM32MP15x - add warning on OTP write and prerequisite: check if MAC address is not yet provisioned. - Use filesize for mmc write command (avoid to write all partition with ${partsize}). ${filesize} and ${partsize} are set by previous load command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13board: ti: am57xx-idk: Prevent boot for invalid configuationRoger Quadros
On am571x-idk there can be following configurations based on Jumper J51 and LCD panel detected. 1) J51 removed (6port): 6 port Ethernet. Disable LCD panel. 2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD. 3) J51 placed (LCD) + Panel not detected/not supported. Configuration 3 is considered invalid as we can't use display nor ICSS1 ethernet ports due to hardware muxing. Alert the user to fix the configuration and prevent boot. Alternative was to allow boot and limit to 4 port Ethernet with no display but this involved introduction of another DTB for the kernel and was considered not worth the hassle. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Suman Anna <s-anna@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>