| Age | Commit message (Collapse) | Author |
|---|
|
Since i2c_init_all always sets the bus back to CONFIG_SYS_SPD_BUS_NUM
for compatibility reasons, it means that any eeprom not located on this
CONFIG_SYS_SPD_BUS_NUM is not accessible with the eeprom commands, even
if you change the bus number with an i2c dev command before.
Furthermore i2c_init_all should disappear and is currently only called
from the early board initialisation sequences, it is not suited for
other usage.
This reverts commit 01a0c64762e902971b34587a8a61b59e9ea51374.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
|
|
Since most commands are not public, make them static. This
prevents warnings that no common prototype is available.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
|
|
When using CONFIG_SYS_I2C i2c needs to be initialized by
i2c_init_all(). This is done in some places but not in
eeprom_init().
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
|
|
The local pointer of address (i.e., addr) only gets
referenced under SPI mode, and it won't be appropriate
to pass only 1-byte addr[1] to i2c_read/i2c_write while
CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 1.
1. In U-boot's I2C model, the address would be re-assembled
to a byte string in MSB order inside I2C controller drivers.
2. The 'CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW' option which could
be found at soft_i2c.c is always turned on in cmd_eeprom.c,
the addr[0] always contains the device address with overflowed
MSB address bits.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
|
|
Data "offset" is not used directly in case of I2C EEPROM. Istead it is
split into "block number" and "offset within mentioned block". Which are
"addr[0]" and "addr[1]" respectively.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
|
|
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
|
|
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
- CONFIG_ENV_EEPROM_IS_ON_I2C
define this, if you have I2C and SPI activated, and your
EEPROM, which holds the environment, is on the I2C bus.
- CONFIG_I2C_ENV_EEPROM_BUS
if you have an Environment on an EEPROM reached over
I2C muxes, you can now define, how to reach this
EEPROM.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Many boards/controllers/drivers don't support an I2C slave interface,
however CONFIG_SYS_I2C_SLAVE is used in common code so provide a
default
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Add support for gzip compressed bmp's (CONFIG_VIDEO_BMP_GZIP).
Add support for eeprom write-enable (CFG_EEPROM_WREN).
Patch by Stefan Roese, 22 Sep 2005
|
|
- Sound commands (beep, wav, sound)
- Test commands (led, can, backlight, rs232)
Patch by Martin Krause, 02 May 2005
|
|
|
|
- show PCI clock frequency on MPC8260 systems
- add FCC_PSMR_RMII flag for HiP7 processors
- in do_jffs2_fsload(), take load address from load_addr if not set
explicit, update load_addr otherwise
- replaced printf by putc/puts when no formatting is needed
(smaller code size, faster execution)
|
|
get rid of MK_CMD_ENTRY macro; update doc/README.command
|
|
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
|
|
- Hymod board database mods: add "who" field and new xilinx chip types
- provide new "init_cmd_timeout()" function so code external to
"common/main.c" can use the "reset_cmd_timeout()" function before
entering the main loop
- add DTT support for adm1021 (new file dtt/adm1021.c; config
slightly different. see include/configs/hymod.h for an example
(requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
CFG_DTT_ADM1021 defined)
- add new "eeprom_probe()" function which has similar args and
behaves in a similar way to "eeprom_read()" etc.
- add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
- gdbtools copyright update
- ensure that set_msr() executes the "sync" and "isync" instructions
after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
- 8260 I/O ports fix: Open Drain should be set last when configuring
- add SIU IRQ defines for 8260
- allow LDSCRIPT override and OBJCFLAGS initialization: change to
config.mk to allow board configurations to override the GNU
linker script, selected via the LDSCRIPT, make variable, and to
give an initial value to the OBJCFLAGS make variable
- 8260 i2c enhancement:
o correctly extends the timeout depending on the size of all
queued messages for both transmit and receive
o will not continue with receive if transmit times out
o ensures that the error callback is done for all queued tx
and rx messages
o correctly detects both tx and rx timeouts, only delivers one to
the callback, and does not overwrite an earlier error
o logic in i2c_probe now correct
- add "vprintf()" function so that "panic()" function can be
technically correct
- many Hymod board changes
|
|
* Add support for LXT971 PHY on PM826
* Patch by Tord Andersson, 16 Jan 2003:
Fix flash sector count for TQM8xxL
* Fix I2C EEPROM problem on ICU862 board (would only write the first
16 bytes out of each 32 byte block)
|
|
|
