| Age | Commit message (Collapse) | Author |
|---|
|
The sub-command parser missed a brace, so "return 0;" is always
taken and no error message is diplayed if you say "i2c scan"
instead of "i2c probe", for example.
Proper brace is added. Also, a misleading and unneeded else
is removed.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com.it>
|
|
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
When CONFIG_I2C_MUX was defined the output of 'help i2c' was not
correct, eg:
=> help i2c
i2c bus [muxtype:muxaddr:muxchannel] - add a new bus reached over muxes.
speed [speed] - show or set I2C bus speed
i2c dev [dev] - show or set current I2C bus
...
It has been changed to:
i2c speed [speed] - show or set I2C bus speed
i2c bus [muxtype:muxaddr:muxchannel] - add a new bus reached over muxes
i2c dev [dev] - show or set current I2C bus
...
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
argc and argv should only be modified once instead of once for
every i2c sub-command
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
New default, weak i2c_get_bus_speed() and i2c_set_bus_speed() functions
replace a number of architecture-specific implementations.
Also, providing default functions will allow all boards to enable
CONFIG_I2C_CMD_TREE. This was previously not possible since the
tree-form of the i2c command provides the ability to display and modify
the i2c bus speed which requires i2c_[set|get]_bus_speed() to be
present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
If I2C Bus is blocked (see doc/I2C_Edge_Conditions),
it is not possible to get out of this, until the
complete Hardware gets a reset. This new commando
calls again i2c_init (and that calls i2c_init_board
if defined), which will deblock the I2C Bus.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Original code displayed:
=> help i2c
i2c i2c speed [speed] - show or set I2C bus speed
i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device
...
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
add CMD_DATA_SIZE macro to enable it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
The last used chip, address, and address length were not being
stored for the imm and imn commands.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the
"i2c sdram" command. This patch provides correct alternative
interpretations when DDR2 memory is detected.
Signed-off-by: Larry Johnson <lrj@acm.org>
|
|
Modify common/Makefile to conditionally compile the cmd_*.c files based
on the board config.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
The "old" i2c commands (iprobe, imd...) are now compiled in again,
even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
config option.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
|
|
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
|
|
Implement various code style fixes and similar changes.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Hello,
Attached is a patch providing support for multiple I2C buses at the
command level. The second part of the patch includes an implementation
for the MPC834x CPU and MPC8349EMDS board.
/*** Note: This patch replaces ticket DNX#2006083042000018 ***/
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Overview:
1. Include new 'i2c' command (based on USB implementation) using
CONFIG_I2C_CMD_TREE.
2. Allow multiple buses by defining CONFIG_I2C_MULTI_BUS. Note that
the commands to change bus number and speed are only available under the
new 'i2c' command mentioned in the first bullet.
3. The option CFG_I2C_NOPROBES has been expanded to work in multi-bus
systems. When CONFIG_I2C_MULTI_BUS is used, this option takes the form
of an array of bus-device pairs. Otherwise, it is an array of uchar.
CHANGELOG:
Added new 'i2c' master command for all I2C interaction. This is
conditionally compiled with CONFIG_I2C_CMD_TREE. New commands added for
setting I2C bus speed as well as changing the active bus if the board
has more than one (conditionally compiled with
CONFIG_I2C_MULTI_BUS). Updated NOPROBE logic to handle multiple buses.
Updated README.
regards,
Ben
|
|
|
|
|
|
- show PCI clock frequency on MPC8260 systems
- add FCC_PSMR_RMII flag for HiP7 processors
- in do_jffs2_fsload(), take load address from load_addr if not set
explicit, update load_addr otherwise
- replaced printf by putc/puts when no formatting is needed
(smaller code size, faster execution)
|
|
add delay to get I2C working with "imm" command and s3c24x0_i2c.c
* Patch by Richard Woodruff, 17 July 03:
- Fixed bug in OMAP1510 baud rate divisor settings.
* Patch by Nye Liu, 16 July 2003:
MPC860FADS fixes:
- add MPC86xADS support (uses MPC86xADS.h)
- add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
o PLPRCR changes
o BRG changes (EXTAL/XTAL restricted to 10MHz)
o don't trust gclk() software measurement by default, depend on
CONFIG_8xx_GCLK_FREQ
- add DRAM SIMM not installed detection
- use more "correct" SDRAM initialization sequence
- allow different SDRAM sizes (8xxADS has 8M)
- default DER is 0
- remove unused MAMR defines from FADS860T.h (all done in fads.c)
- rename MAMR/MBMR defines to be more consistent. Should eventually
be merged into MxMR to better reflect the PowerQUICC datasheet.
* Patch by Yuli Barcohen, 16 Jul 2003:
support new Motorola PQ2FADS-ZU evaluation board which replaced
MPC8260ADS and MPC8266ADS
|
|
get rid of MK_CMD_ENTRY macro; update doc/README.command
|
|
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
|
|
|
