| Age | Commit message (Collapse) | Author |
|---|
|
Attempting to place device tree immediately after an image in memory can lead
to mis-aligned data accesses if that image size is not divisible by the
alignment requirements of the architecture.
Data aborts caused by this were observed on a custom Marvel A388 based system,
where the image was a uboot FIT file. The total size varies depending on the
uboot device tree size, which does not always lead to correct alignment.
The minimum alignment specified for ARM [1] and ARM64 [2] linux booting has been
used
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm/booting.rst#n126
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm64/booting.rst#n45
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
|
|
Need initialize UDC before run sdp download
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
usb_init() may be called multiple times for fetching multiple images
from SPL. Skip reinitializing USB if its already been done
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Create a new API spl_usb_load() that takes the filename as a parameter
instead of taking the default U-boot PAYLOAD_NAME
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
Add support for SquashFS filesystem. Right now, it does not support
compression but support for zlib will be added in a follow-up commit.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
|
|
In some cases SPL needs to be able to erase but TPL just needs to read.
Allow these to have separate settings for SPI_FLASH_TINY.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_NAND_BASE
CONFIG_SPL_NAND_IDENT
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Commit 40686c394e53 ("riscv: Clean up IPI initialization code")
caused U-Boot failed to boot on SiFive HiFive Unleashed board.
The codes inside arch_cpu_init_dm() may call U-Boot timer APIs
before the call to riscv_init_ipi(). At that time the timer register
base (e.g.: the SiFive CLINT device in this case) is unknown yet.
It might be the name riscv_init_ipi() that misleads people to only
consider it is related to IPI, but in fact the timer capability is
provided by the same SiFive CLINT device that provides the IPI.
Timer capability is needed for both UP and SMP.
Considering that the original refactor does have benefits, that it
makes the IPI code more similar to U-Boot initialization idioms.
It also removes some quite ugly macros. Let's do the minimal revert
instead of a complete revert, plus a fixes to arch_cpu_init_dm() to
consider the SPL case.
Fixes: 40686c394e53 ("riscv: Clean up IPI initialization code")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Leo Liang <ycliang@andestech.com>
|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
- Despite other ext4 filesystem functions, ext4fs_mount returns
0 in case of error.
- This leads to u-boot crash in case that an SD card
with valid partition table but without ext4 filesystem created
in a partition is found on SD card.
- Fix this by returning a proper error code of '-1' from spl_load_image_ext
function in case of ext4fs_mount error.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
[hthiery: slightly reword the commit message]
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Replacing the ret variable with err and handling first the error
condition about the value returned by the spl_nand_fit_read routine,
improves the code readability.
Furthermore, the 'else' int the 'else return ret' instruction was
useless.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
The offset at which the image to be loaded from NAND is located is
retrieved from the itb header. The presence of bad blocks in the area
of the NAND where the itb image is located could invalidate the offset
which must therefore be adjusted taking into account the state of the
sectors concerned.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
If uboot does not embed its device tree and the FIT loading function
returns error in case of failure in the FDT append, the redundant itb
image could be loaded.
cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Merge all outstanding changes from the current next branch in now that
we have released.
|
|
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
|
|
The previous IPI code initialized the device whenever the first call was
made to a riscv_*_ipi function. This made it difficult to determine when
the IPI device was initialized. This patch introduces a new function
riscv_init_ipi. It is called once during arch_cpu_init_dm. In SPL, it is
called in spl_invoke_opensbi. Before this point, no riscv_*_ipi functions
should be called.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The current recommendation for best security practice from the US government
is to use SHA384 for TOP SECRET [1].
This patch adds support for SHA384 and SHA512 in the hash command, and also
allows FIT images to be hashed with these algorithms, and signed with
sha384,rsaXXXX and sha512,rsaXXXX
The SHA implementation is adapted from the linux kernel implementation.
[1] Commercial National Security Algorithm Suite
http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
|
|
Add U-Boot proper sector start offset for SiFive FU540.
This value is based on the partition layout supported
by SiFive FU540.
u-boot.itb need to write on this specific offset so-that
the SPL will retrieve it from here and load.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
In a loading chain SPL -> ATF (->OP-TEE) -> U-Boot, ATF and a subsequent
OP-TEE will re-use the same fdt as the U-Boot target and may need the
information about usable memory ranges.
Especially OP-TEE needs this to initialize dynamic shared memory
(the only type U-Boot implements when talking to OP-TEE).
So allow spl_fixup_fdt() to take a fdt_blob argument, falling back to
the existing CONFIG_SYS_SPL_ARGS_ADDR if needed and call it from the
ATF path as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this fairly uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Some of the enum members are wrong. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A large number of boards call preloader_console_init unconditionally.
Currently, they fail to build with CONFIG_SPL_SERIAL=n, because the
function is undefined in that case. To fix the build, always define
preloader_console_init, but make it no-op when CONFIG_SPL_SERIAL=n.
For the few boards that did check for CONFIG_SPL_SERIAL before calling
preloader_console_init, remove the checks, since the function can now
be called unconditionally.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Have this symbol follow the pattern of all other such symbols.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
|
|
When enable CONFG_SPL_DM_USB_GADGET, sdp should use
usb_gadget_initialize() and usb_gadget_release() to
support DM gadget driver.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Because SDP directly jumps to next level boot image, we'd better
clean up the USB driver before it. Implement a weak callback function,
that spl sdp can use it to clean up USB driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add a new configuration CONFIG_SPL_SDP_USB_DEV to specify the
usb index for spl sdp driver, so that we change use different device.
The default value is 0.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Need initialize UDC before run sdp download
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
mode"
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases; using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined. In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9fdd
("common: Pass the boot device into spl_boot_mode()").
This reverts commit 772b55723bcbe8ebe84f579d9cdc831d8e18579d.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
|
|
This patch adds support for decompressing LZMA compressed u-boot payload
in legacy uImage format.
Using this patch together with u-boot-lzma.img may be useful for some
platforms as they can reduce the size and load time of u-boot payload.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
With the if statement now for the legacy image handling, the compiler
now generates this compile time warning:
common/spl/spl_nor.c:27:6: warning: unused variable 'ret' [-Wunused-variable]
This patch removes this warning by changing the 'ret' variable handling.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Move the legacy image loading into spl_legacy.c. This makes it easier
to extend the legacy image handling with new features that other
SPL loaders might use (e.g. spl_spi.c etc).
No functional change intended.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Use IS_ENABLED() instead of #ifdef CONFIG_ to remove one #ifdef.
No functional change intended.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This patch moves the legacy image handling into a separate file, which
will be extended with other legacy image features later.
No function change intended.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
The free() function checks if its argument is NULL. It is superfluous to do
the same check on the calling side.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Two nearly concurrent commits (d4d65e112 and bcee8d676) added a
SPL_DM_GPIO symbol. Resolve the duplication in favor of the version
in drivers/gpio/Kconfig.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
With SBI v0.2 HSM extension, only a single hart need to boot and
enter operating system. The booting hart can bring up secondary
harts one by one afterwards.
For U-Boot running in SPL, SMP can be turned on, while in U-Boot
proper, SMP can be optionally turned off if using SBI v0.2 HSM.
Introduce a new SPL_SMP Kconfig option to support this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
This function is only relevant to the MMC driver so calling it
spl_boot_partition() might be confusing. Rename it to
spl_mmc_boot_partition() to make its purpose more clear (and bring
it in line with spl_mmc_boot_mode()).
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).
Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.07
common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code
xilinx:
- Enable netconsole
Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE
Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver
ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3
Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR
Drivers:
- Gem:
- Flush memory after freeing
- Handle mdio bus separately
- Watchdog:
- Get rid of unused global data pointer
- Enable window watchdog timer
- Serial:
- Change reinitialization logic in zynq serial driver
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Commit cf8dcc5d02c3 ("common: spl_fit: Default to IH_OS_U_BOOT if
FIT_IMAGE_TINY enabled") is not correct, it will append fdt to each loadable
image. Actually when using TINY FIT, the first loadable image is thought as
u-boot and already have fdt appended.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
The default SPL / TPL linker script is in the $(ARCH) directory. The
way we use this today works but isn't ideal. With an update to Kconfig
to re-sync with the Linux Kernel, we need to escape the '$' here so that
it will end up being evaluated by make.
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
|
