| Age | Commit message (Collapse) | Author |
|---|
|
Move env_get() over to the new header file.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The FIT image could contain the splash data in 3 different structure:
- The splash data is embedded in FIT image (internal)
In this case, the property 'data' presents in FIT image header. And
internal information 'start' and 'end' represent the location and
size of splash data inside of FIT image.
- The splash data is external with absolute position in FIT image
This case is made by 'mkimage -p [pos]'. The splash data is stored
at the absolute position. Instead the property 'data', the properties
'data-position' and 'data-size' are used to specify the location and
size of the splash data.
- the splash data is external with relative offset in FIT image
This case is made by 'mkimage -E'. The splash data is placed after
the FIT image header with 4 byte alignment. Instead the property
'data', the properties 'data-offset' and 'data-size' are used to
specify the location and size of the splash data.
Currently, the splash only support to load external data with relative
offset from FIT image. This commit make it possible to load the splash
data embedded in FIT image or the external data with absolute position
This inspiration comes from Simon Glass <sjg@chromium.org>, see
common/spl_fit.c
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
The splash image could be loaded from different sources (e.g. sf, mmc)
with different formats (e.g. raw, file-system). These sources are
structured by a board dependent object 'splash_location'. To decide
where is the splash image loaded, following environment variables are
used to select the splash source and file:
- 'splashsource' is used to select the splash source by setting its
value to specified name of splash location.
- 'splashfile' specify the name of splash image file
But, when loads the splash image from FIT, the name of splash image
within FIT is specified by splash location name. Due to the splash
location name is already used for the splash source, its name may
conflicts with the name of splash image.
To solve the conflict, the environment variable 'splashfile' is used
to specify the splash image in FIT, and keeps the splash location
name for the splash source.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Before reading entire FIT image, add sanity check by testing image
header against FDT_MAGIC. This should help avoid problems in situations
where FIT is not yet available from storage device, for example when
performing initial programming of device.
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
This reverts commit 1d20170467b079642be96996dcd71db64c3c365c, reversing
changes made to 6aee2ab68c362ace5a59f89a63abed82e0bf19e5.
The mxc_ipuv3_fb.c changes introduce build failures on some targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Before reading entire FIT image, add sanity check by testing image
header against FDT_MAGIC. This should help avoid problems in situations
where FIT is not yet available from storage device, for example when
performing initial programming of device.
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
|
|
Update this command to support driver model. This has a different way of
starting and stopping SATA.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
|
|
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Passing NULL to fs_read() for actread value results in hanging U-Boot
at least on our ARM plattform (TI AM335x). Since fs_read() and
following functions do not catch nullpointers, writing to 0x0 occurs.
Passing a local dummy var instead of NULL solves this issue.
Signed-off-by: Jonathan Golder <jonathan.golder@kurz-elektronik.de>
Cc: Anatolij Gustschin <agust@denx.de>
|
|
SPLASH_STORAGE_RAW is defined as 0, so a check against & will
never be true. These flags are never combined so do a check
against == instead.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Enable support for loading a splash image from within a FIT image.
The image is assumed to be generated with mkimage -E flag to hold
the data external to the FIT.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Sort include files in accordance to U-Boot coding style.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
|
|
Current implementation of splash_init_usb() requires usb_stor_scan()
which doesn't exist in case of DM_USB simply because real probing
happens right in usb_init().
So disable usage of usb_stor_scan() in case of DM_USB.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Robert Winkler <robert.winkler@boundarydevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support for loading splash image from NAND Flash formatted with a (UBI) filesystem.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Add support for loading splashimage from filesystem formatted sata
storage.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add support for loading splash image from USB drive formatted with a
filesystem.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Add support for loading splash image from an SD card formatted with
a filesystem. Update boards to maintain original behavior where needed.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
|
Rename raw read functions to *_read_raw() in preparation for supporting
read_fs() feature.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
Move board/compulab/common/splash.c code to
common/splash_source.c to make it available for everybody. This move
renames cl_splash_screen_prepare() to splash_source_load(), and
the compilation of this code is conditional on CONFIG_SPLASH_SOURCE.
splash_source features:
* Provide a standardized way for declaring board specific splash screen
locations
* Provide existing routines for auto loading the splash image from the
locations as declared by the board
* Introduce the "splashsource" environment variable, which makes it
possible to select the splash image source.
cm-t35 and cm-fx6 are updated to use the modified version.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
