| Age | Commit message (Collapse) | Author |
|---|
|
When use the CONFIG_ENV_IS_NOWHERE, I met such issue:
DRAM: 256 MiB
Using default environment
*** Warning - bad CRC, using default environment
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
Boards can pass display timing info for drivers using EDID
block. Provide common function to add board specific EDID
data to the device tree. Subsequent patch makes use of this
functionality.
Detailed timing descriptor data from EDID is used for
programming the display controller. This is currently
implemented on the Linux side by the fsl-diu-fb frame
buffer driver and it is documented there in
Documentation/powerpc/dts-bindings/fsl/diu.txt.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
|
|
The include <jffs2/jffs2.h> is still necessary though.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
|
|
Most people don't use the 'rarpboot' command, so only enable it when
CONFIG_CMD_RARP is defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Consolidate some code in mtd_get_len_incl_bad(), and fix a condition
where a valid partition could be reported as truncated if it has a
good block at the end of the device (unlikely, since the BBT is usually
there).
Fix mid-block declarations in net_part_size().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
This patch adds a new 'mtdparts add' variant: add.spread. This command variant
adds a new partition to the mtdparts variable but also increases the partitions
size by skipping bad blocks and aggregating any additional bad blocks found at
the end of the partition.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
|
|
This patch introduces the 'spread' sub-command of the mtdparts command.
This command will modify the existing mtdparts variable by increasing
the size of the partitions such that 1) each partition's net size is at
least as large as the size specified in the mtdparts variable and 2)
each partition starts on a good block.
The new subcommand is implemented by iterating over the mtd device
partitions and collecting a bad blocks count in each -- including any
trailing bad blocks -- and then modifying that partitions's part_info
structure and checking if the modification affects the next partition.
This patch is based on a port of the 'dynnamic partitions' feature by
Harald Welte <laforge@gnumonks.org>; ported from commit
e05835df019027391f58f9d8ce5e1257d6924798 of
git://git.openmoko.org/u-boot.git. Whereas Harald's feature used a
compile-time array to specify partitions, the feature introduced by
this patch uses the mtdparts environment variable.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
|
|
This patch adds an additional column to the output of list_partitions. The
additional column will contain the net size and a '(!)' beside it if the net
size is not equal to the partition size.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
|
|
The get_mtd_device_nm function is called in a couple places and the
string that is passed to it is not really used after the calls.
This patch regroups the calls to this function into a new function,
get_mtd_info.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Stefan Roese <sr@denx.de>
CC: Wolfgang Denk <wd@denx.de>
|
|
The dump command is made to increment its address on repeat,
as md does. Other commands do not make sense to issue repeatedly,
and can be irritating when it happens accidentally, so don't.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
- If the current device is overridden by a named partition,
- update the caller's pointer/index, rather than copy over the
nand_info struct, and
- be sure to call board_nand_select_device even when the device
is overridden by a named partition.
- Support 64-bit offsets/sizes in a few more places.
- Refactor arg_off_size for added readability and flexibility,
and some added checks such as partition size.
- Remove redundant check for bad subcommands -- if there's no match
it'll print usage when it gets to the end anyway.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
|
|
|
|
|
|
Commit 55e97429d1e6cf0976711e4e0f29ea924b7e5917 removed the definition
from /arch/i386/include/asm/u-boot.h but not its usage in do_bdinfo()
|
|
and clean up error messages and help,
removed pointless debug() call.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The MAX_CMDBUF_SIZE define is unneeded as it should always
equal CONFIG_SYS_CBSIZE.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The current ELF loading function does a lot of work above and beyond a
simple "loading". It ignores the real load addresses and loads things
into their virtual (runtime) address. This is undesirable when we just
want it to load an ELF and let the ELF do the actual C runtime init.
So add a command line option to let people choose to load via either the
program or section headers. I'd prefer to have program header loading
be the default, but this would break historical behavior, so I'll leave
section header loading as the norm.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch fixes the compilation problem introduced with commit
e3c78c9b [ppc4xx: Remove now unused CONFIG_UART1_CONSOLE]:
-> ./MAKEALL TB5200
Configuring for TB5200 board...
serial.c: In function '__default_serial_console':
serial.c:94: warning: no return statement in function returning non-void
I accidentally removed an "#else" line. This patch adds it back.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
commit ea882baf9c17cd142c99e3ff640d3ab01daa5cec introduces
a command_sub_table for the "env" command. On arm, avr32, m68k,
mips and sparc architectures, relocation needs manual fixups,
so add these fixups for this sub command table too.
Tested on arm/qong board.
mips board (Ben NanoNote) from Xiangfu Liu
arm/AT91 board from Reinhard Meyer
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
cc: Xiangfu Liu <xiangfu@openmobilefree.net>
cc: Reinhard Meyer <u-boot@emk-elektronik.de>
cc: sshtylyov@mvista.com
|
|
Previously the function was set_default_env(void), it is now
set_default_env(const char *s). This patch adds the required
parameter. This fixes a broken build on OMAP4430 SDP.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
|
|
|
|
This patch fixes a bug in fdt_fixup_nor_flash_node() when the reg
property has multiple reg tuples, like:
reg = <0 0x00000000 0x04000000
0 0x04000000 0x04000000>;
In this case this function did not update the reg property correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The OTP code does a little shuffling of arguments that aren't really
necessary, so use a local variable instead to fix build errors now
that the args[] parameter is const.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Conflicts:
include/ppc4xx.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Add OSE as operating system for mkimage and bootm.
Signed-off-by: Torkel Lundgren <torkel.lundgren@enea.com>
|
|
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now
removed since the move from the 4xx UART driver to the common NS16550
UART driver. Let's remove all references to this define now.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.
The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.
All PPC4xx board config headers are changed to use this common NS16550
driver now.
Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch changes the behaviour of the fdt_fixup_nor_flash_node()
function. Now it doesn't patch the size of the "reg" property with the
chip-select size, but with the size returned from the new function
flash_get_bank_size(). This function will return per weak default the
flash size of the bank (bank = chip-select numer) detected by the flash
driver. If this does not fit your needs, this function may be overridden
by a board specific one.
For this the parameters needed to be changed. So I intentionally squashed
the PPC4xx stuff using this routine into this patch. Otherwise it would
not be git-bisectable anymore.
The board specific function for the AMCC/APM Ebony eval board is now
included in this patch version.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Detlev Zundel <dzu@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Rather than using a custom "Usage:", use the common cmd_usage() function,
and tail into it now that it returns 1 for us.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
|
|
Now that the defines are moved to header files we don't need this
conditional compilation any more. Remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch simplifies the use of CONFIG_SYS_MAX_FLASH_BANKS_DETECT. By
moving these optional variables and defines into the common code, board
specific code is minimized. Currently only the following board use
this feature:
APC405, IDS8247, TQM834x
And IDS8247 doesn't seem to really need this feature, since its not
updating the bank number variable at all. So this patch removes the
definition of CONFIG_SYS_MAX_FLASH_BANKS_DETECT from this board port.
This new framework will be used by the upcoming lwmon5 update as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
|
|
Recent changes caused that the HMI10 board now is included in the
boards built by MAKEALL, which revealed that compilation for this
board has been broken for a long time:
ps2ser.c: In function 'ps2ser_init':
ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function)
ps2ser.c:155: error: (Each undeclared identifier is reported only once
ps2ser.c:155: error: for each function it appears in.)
ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function)
ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function)
ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function)
ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function)
ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function)
ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function)
ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_putc':
ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_getc_hw':
ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function)
ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function)
ps2ser.c: In function 'ps2ser_interrupt':
ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function)
The board is orphaned, and AFAICT has reached EOL.
Drop support for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
!! This breaks support for all arm boards !!
To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"
!! This define will be removed soon, so convert your
board to use relocation support
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
fixup_cmdtable() did all work for fixing up the cmdtable,
if CONFIG_RELOC_FIXUP_WORKS is not defined.
CONFIG_RELOC_FIXUP_WORKS is missing for i386! I talked
with Graeme Russ, and he will fix this soon.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
bi_env is nowhere used, so delete it!
Signed-off-by: Heiko Schocher <hs@denx.de>
similar patch posted from Dirk Behme Tue Jul 27 18:36:09 CEST 2010
http://lists.denx.de/pipermail/u-boot/2010-July/074542.html
|
|
Motivation:
* Old environment code used a pessimizing implementation:
- variable lookup used linear search => slow
- changed/added variables were added at the end, i. e. most
frequently used variables had the slowest access times => slow
- each setenv() would calculate the CRC32 checksum over the whole
environment block => slow
* "redundant" envrionment was locked down to two copies
* No easy way to implement features like "reset to factory defaults",
or to select one out of several pre-defined (previously saved) sets
of environment settings ("profiles")
* No easy way to import or export environment settings
======================================================================
API Changes:
- Variable names starting with '#' are no longer allowed
I didn't find any such variable names being used; it is highly
recommended to follow standard conventions and start variable names
with an alphanumeric character
- "printenv" will now print a backslash at the end of all but the last
lines of a multi-line variable value.
Multi-line variables have never been formally defined, allthough
there is no reason not to use them. Now we define rules how to deal
with them, allowing for import and export.
- Function forceenv() and the related code in saveenv() was removed.
At the moment this is causing build problems for the only user of
this code (schmoogie - which has no entry in MAINTAINERS); may be
fixed later by implementing the "env set -f" feature.
Inconsistencies:
- "printenv" will '\\'-escape the '\n' in multi-line variables, while
"printenv var" will not do that.
======================================================================
Advantages:
- "printenv" output much better readable (sorted)
- faster!
- extendable (additional variable properties can be added)
- new, powerful features like "factory reset" or easy switching
between several different environment settings ("profiles")
Disadvantages:
- Image size grows by typically 5...7 KiB (might shrink a bit again on
systems with redundant environment with a following patch series)
======================================================================
Implemented:
- env command with subcommands:
- env print [arg ...]
same as "printenv": print environment
- env set [-f] name [arg ...]
same as "setenv": set (and delete) environment variables
["-f" - force setting even for read-only variables - not
implemented yet.]
- end delete [-f] name
not implemented yet
["-f" - force delete even for read-only variables]
- env save
same as "saveenv": save environment
- env export [-t | -b | -c] addr [size]
export internal representation (hash table) in formats usable for
persistent storage or processing:
-t: export as text format; if size is given, data will be
padded with '\0' bytes; if not, one terminating '\0'
will be added (which is included in the "filesize"
setting so you can for exmple copy this to flash and
keep the termination).
-b: export as binary format (name=value pairs separated by
'\0', list end marked by double "\0\0")
-c: export as checksum protected environment format as
used for example by "saveenv" command
addr: memory address where environment gets stored
size: size of output buffer
With "-c" and size is NOT given, then the export command will
format the data as currently used for the persistent storage,
i. e. it will use CONFIG_ENV_SECT_SIZE as output block size and
prepend a valid CRC32 checksum and, in case of resundant
environment, a "current" redundancy flag. If size is given, this
value will be used instead of CONFIG_ENV_SECT_SIZE; again, CRC32
checksum and redundancy flag will be inserted.
With "-b" and "-t", always only the real data (including a
terminating '\0' byte) will be written; here the optional size
argument will be used to make sure not to overflow the user
provided buffer; the command will abort if the size is not
sufficient. Any remainign space will be '\0' padded.
On successful return, the variable "filesize" will be set.
Note that filesize includes the trailing/terminating '\0'
byte(s).
Usage szenario: create a text snapshot/backup of the current
settings:
=> env export -t 100000
=> era ${backup_addr} +${filesize}
=> cp.b 100000 ${backup_addr} ${filesize}
Re-import this snapshot, deleting all other settings:
=> env import -d -t ${backup_addr}
- env import [-d] [-t | -b | -c] addr [size]
import external format (text or binary) into hash table,
optionally deleting existing values:
-d: delete existing environment before importing;
otherwise overwrite / append to existion definitions
-t: assume text format; either "size" must be given or the
text data must be '\0' terminated
-b: assume binary format ('\0' separated, "\0\0" terminated)
-c: assume checksum protected environment format
addr: memory address to read from
size: length of input data; if missing, proper '\0'
termination is mandatory
- env default -f
reset default environment: drop all environment settings and load
default environment
- env ask name [message] [size]
same as "askenv": ask for environment variable
- env edit name
same as "editenv": edit environment variable
- env run
same as "run": run commands in an environment variable
======================================================================
TODO:
- drop default env as implemented now; provide a text file based
initialization instead (eventually using several text files to
incrementally build it from common blocks) and a tool to convert it
into a binary blob / object file.
- It would be nice if we could add wildcard support for environment
variables; this is needed for variable name auto-completion,
but it would also be nice to be able to say "printenv ip*" or
"printenv *addr*"
- Some boards don't link any more due to the grown code size:
DU405, canyonlands, sequoia, socrates.
=> cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Stefan Roese <sr@denx.de>,
Heiko Schocher <hs@denx.de>
- Dropping forceenv() causes build problems on schmoogie
=> cc: Sergey Kubushyn <ksi@koi8.net>
- Build tested on PPC and ARM only; runtime tested with NOR and NAND
flash only => needs testing!!
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>,
Cc: Stefan Roese <sr@denx.de>,
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
|
|
So far, getenv() would work before relocation is most cases, even
though it was not intended to be used that way. When switching to a
hash table based implementation, this would break a number of boards.
For convenience, we make getenv() check if it's running before
relocation and, if so, use getenv_f() internally.
Note that this is limited to simple cases, as we use a small static
buffer (32 bytes) in the global data for this purpose.
For this reason, it is also not a good idea to convert all current
uses of getenv_f() into getenv() - some of the existing use cases need
to be able to deal with longer variable values, so getenv_f() is still
needed and recommended for use before relocation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This (undocumented) concept was only in use for the MVSMR and
davinci_schmoogie Sergey Kubushyn <ksi@koi8.net> boards.
Drop it for now. If really needed, it should be reimplemented
later in the context of the new environment command set.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
|
|
This patch is to save environment data to mmc card.
It uses interfaces defined in generic mmc.
Signed-off-by: Terry Lv <r65388@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
x86 failed to compile with a message "a case for this architecture does
not exist!" - Add do_bdinfo() for this arch
|
|
Coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
|
|
|
|
|
