| Age | Commit message (Collapse) | Author |
|---|
|
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Some DVI monitors don't show anything in HDMI mode since audio stream
confuses them. To solve this situation, this commit adds HDMI flag in
timing data and sets it accordingly during edid parsing.
First existence of extension block is checked. If it exists and it is
CEA861 extension, then data blocks are checked for presence of HDMI
vendor specific data block. If it is present, HDMI flag is set.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Timing flags are never set, so they may contain garbage. Since some
drivers check them, video output may be broken on those drivers.
Initialize them to 0 and check for few common flags.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With gcc-6 and later we may get a warning such as:
.../common/cli_readline.c:20:21: warning: ‘tab_seq’ defined but not used [-Wunused-const-variable=]
static const char tab_seq[] = " "; /* used to expand TABs */
^~~~~~~
.../common/cli_readline.c:19:19: warning: ‘erase_seq’ defined but not used [-Wunused-const-variable=]
static const char erase_seq[] = "\b \b"; /* erase sequence */
^~~~~~~~~
Because in SPL we're normally not doing interactive commands anyhow, so
lets just not compile this at all in SPL. This also means that we need
to correct the logic (and comment) about what the drivers/ddr/fsl/ and
CONFIG_FSL_DDR_INTERACTIVE requires and this will be included in SPL
there.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
env_attr_lookup call env_attr_walk with
callback = regex_callback.
In env_attr_walk
attributes = strchr(entry_cpy, ENV_ATTR_SEP)
will return NULL if ENV_ATTR_SEP is not found.
In the aftermath regex_callback may call
strlen(attributes)
with a NULL value which will lead to a failure.
The problem was indicated by scan-clam.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Error codes should be negative.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The SPL-DFU feature enable to load and
execute u-boot from RAM over usb from
PC using dfu-util.
Hence dfu-reset should not be issued
when dfu-util -R switch is issued.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
|
|
Since SPL_DFU_SUPPORT is depends on SPL_RAM_SUPPORT,
hence select SPL_DFU_SUPPORT only when
SPL_RAM_SUPPORT is chosen.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
In single stage bootmode or falcon boot mode, the SPL shall update the
device tree that we load with the normal fixups done via
arch_fixup_fdt(), when possible (ie we have enough information in this
restricted environment to be able to do that still). This will include
for example updating them memory nodes.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[trini: Reword commit message]
|
|
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.
This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Move the assignment of board info to global data a bit early which is
safe,
so that ram details can be used to enable caches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
For the RK3399-Q7, we need some flexibility (depending on the feature
set we include in the SPL stage and how large our SPI flash is) in
positioning the SPL payload (i.e. the FIT image containing U-Boot, ATF
and the M0 payload) in our SPI flash.
To avoid having to deal with this through different U-Boot images, we
introduce a the '/config/u-boot,spl-payload-offset' property node
allow it to override the default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Similar to what blk_get_device_part_str() does, this patch makes
part_get_info_by_name() return the partition number in case of a match.
This is useful when the partition number is needed and not just the
descriptor.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update the Android image header format to the latest version published
in AOSP. The original code moved to a new repository, so this patch also
updates the reference to that path.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Allow this to work with CONFIG_DM_VIDEO enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
Adjust this function so that we can convert it to support CONFIG_DM_VIDEO
without a lot of code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
The DM version of scsi_scan() is becoming a bit long, it can be split:
scsi_scan() iterates over the IDs and LUNs and for each id/lun pair calls
do_scsi_scan_one() to do the work of:
- detecting an attached drive
- creating the associated block device if a drive is found.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
simpler to read
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
this makes it easier comparable to the double-buffered version
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
setup_flash_device selects one of two code paths depending on the driver
model being used (=CONFIG_DM_SPI_FLASH). env_relocate_spec only used
the non driver-model code path. I'm unsure why, either none of the
platforms that need relocation use the driver model, or - worse - the
driver model is not yet usable when relocating.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
copy&paste code found in single/double buffered code path
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
With 3f66149d9fb4 we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9fb4 ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With DM_SCSI enabled, blk_create_devicef() is called with blkz = 0, leading
to a divide-by-0 exception.
scsi_detect_dev() can be used to get the required parameters (block size
and number of blocks) from the drive before calling blk_create_devicef().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We might want to get information about the scsi device without initializing the partition.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is a cosmetic change. target and LUN have kind of the same role in
this function. One of them was passed as a parameter and the other was
embedded in a structure. For consistency, pass both of them as parameters.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This fixes a regression caused by
commit 07b2b78ce4bc8ae25e066c65245eaf58c0d9a67c
dm: usb: Convert USB storage to use driver-model for block devs
which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
### ERROR ### Please RESET the board ###
This happens because dev_desc->blksz is 0.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
|
|
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move U-Boot private data into a separate file. This
lets export fw_env.h to be used by external programs
that want to change the environment using the library
built in tools/env.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
FIT support in the net boot case is much like the RAM boot case in that
we load our image to "load_addr" and pass a dummy read function into
"spl_load_simple_fit()". As the load address is no longer hard-coded to
the final execution address, legacy image loading will require load_addr
to be set correctly in the image header.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
|
|
Under the plethora of #ifdefs, the xyzModem code hid this pearl:
static char *zm_out = (char *) 0x00380000;
This was only enabled when DEBUG is defined, so it's probably why it
went unnoticed for so long. No idea what platform had memory at that
exact location, but the this approach is extremely hacky.
Use a static buffer instead.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
|
|
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
|
|
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The default value of BOOTSTAGE_STASH_SIZE should be set to hexadecimal,
but an integer value is set. This fixes the BOOTSTAGE_STASH_SIZE number
from hexadecimal to integer.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit:
f99993c10882f7dc8ec35993d5febe59aac01e6a
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
ft_cpu_setup() already calls fdt_fixup_ethernet(), calling it
in image_setup_libfdt() is both redundant and breaks any modifications
done by ft_board_setup(). Restore the old behavior by removing
the call in image_setup_libfdt()
Fixes: 13d06981a982 ("image: Add device tree setup to image library")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
|
|
SPL has been restricted to use only dev 0 based on the assumption that only
one MMC device is registered. This is not always the case and many
platforms now register several devices as expected by the spl mmc boot code
For those platform SPL_ENV_SUPPORT is broken if dev is forced to 0.
A word of warning: this commit may break SPL_ENV_SUPPORT on platforms that
do not register the same MMC controllers in SPL and in u-boot (mostly iMX6
based platforms). Fortunately none of those activate SPL_ENV_SUPPORT in
their default configuration.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).
Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.
Once done, also remove the irrelevant sunxi defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
With d53ecad92f06 some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
These includes don't seem to be needed now. Drop them. Reserve the
mp.h header for PowerPC for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This is to keep the header file order consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Drop headers which are not used or needed in this file. The compiler.h
header is included by common.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
