| Age | Commit message (Collapse) | Author |
|---|
|
When a regulator command cannot honour the requested voltage, display the
limits to try to be helpful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
|
|
The following commit enforces CONFIG_DM_ETH for USB Ethernet which
breaks any board using CONFIG_USB_HOST_ETHER without CONFIG_DM_ETH
which this patch fixes.
commit 69559093f6173dcfcb041df0995063bdbd07d49b
dm: usb: Avoid using USB ethernet with CONFIG_DM_USB and no DM_ETH
Tested on Colibri T20/T30 as well as Apalis T30 with
CONFIG_USB_HOST_ETHER and CONFIG_USB_ETHER_ASIX enabled and a LevelOne
USB-0301 ASIX AX88772 dongle.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The code in question polls an USB port status via USB_REQ_GET_STATUS
to determine whether there is a device on the port or not. The way to
figure that out is to check two bits. Those are wPortChange[0] and
wPortStatus[0].
The wPortChange[0] indicates whether some kind of a connection status
change happened on a port (a device was plugged or unplugged). The
wPortStatus[0] bit indicates the status of the connection (plugged or
unplugged).
The current code tests whether wPortChange[0] == wPortStatus[0] and
if that's the case, considers the loop polling for the presence of a
USB device on port finished.
This works for most USB sticks, since they come up really quickly and
trigger the USB port change detection before the first iteration of the
detection loop happens. Thus, both wPortChange[0] and wPortStatus[0]
are set to 1 and thus equal. The loop is existed in it's first iteration
and the stick is detected correctly.
The problem is with some obscure USB sticks, which take some time before
they pop up on the bus after the port was enabled. In this case, both
the wPortChange[0] and wPortStatus[0] are 0. They are equal again, so
the loop again exits in the first iteration, but this is incorrect, as
such USB stick didn't have the opportunity to get detected on the bus.
Rework the code such, that it checks for wPortChange[0] first to test
if any connection change happened at all. If no change occured, keep
polling. If a change did occur, test the wPortStatus[0] to see there is
some device present on the port and only if this is the case, break out
of the polling loop.
This patch also trims down the duration of the polling loop from 10s
per port to 1s per port. This is still annoyingly long, but there is
no better option in case of U-Boot unfortunatelly. This change will
most likely increase the duration of 'usb start' on some platforms,
but this is needed to fix a bug.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
|
|
The EFI memory map is passed from the stub to U-Boot in a table. Add a
command to display it in a vaguely readable fashion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on QEMU
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When running U-Boot as an EFI application we cannot relocate since we do not
have relocation information. U-Boot has already been relocated to a suitable
address.
Add a global_data flag to control skipping relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When U-Boot runs as an EFI application is does not have a definition of
CONFIG_SYS_TEXT_BASE. U-Boot is a relocatable application and the relocation
is done by EFI. U-Boot can be loaded at any address.
This is similar to how sandbox works. Adjust the early board init to deal
with this.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add '\n' for debug msg.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Do not print confusing "Board: Unknown" during boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
Use one command for showing overall CPU status than several without
knowing how many cpus is available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The sysboot and pxe commands currently support either U-Boot formats or
raw zImages. Add support for the AArch64 Linux port's native image format
too.
As with zImage support, there is no auto-detection of the native image
format. Rather, if the image is auto-detected as a U-Boot format, U-Boot
will try to interpret it as such. Otherwise, U-Boot will fall back to a
raw/native image format, if one is enabled.
My belief is that CONFIG_CMD_BOOTZ won't ever be enabled for any AArch64
port, hence there's never a need to differentiate between CONFIG_CMD_
_BOOTI and _BOOTZ at run-time; compile-time will do. Even if this isn't
true, we want to prefer _BOOTI over _BOOTZ when defined, since _BOOTI is
definitely the native format for AArch64.
Change-Id: I83c5cc7566032afd72516de46f4e5eb7a780284a
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
property
In case of enable CONFIG_OF_CONTROL and has a "model" property in the root node,
the board special "checkboard" will not be called.
Usually we show some useful version information in the function.
This patch enable call "checkboard" in any case.
It is not conflicting with showing "model" at the same time.
For example on LS2085AQDS:
Showing "model" only:
Model: Freescale Layerscape 2085a QDS Board
Showing "checkboard" only:
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Showing both:
Model: Freescale Layerscape 2085a QDS Board
Board: LS2085E-QDS, Board Arch: V1, Board version: B, boot from vBank: 4
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
This patch introduces the option to boot from a MMC card parition with
an offset. This can be done by using both defines together:
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR ((160 << 10) / 512)
The example above loads the main U-Boot at offset 160KiB from the MMC
partition 1.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
Since we're now using a dynamic controller index for fastboot too,
usb_gadget_handle_interrupts should be using it instead of 0 (despite the fact
that it's currently not being used at all in the musb-new implementation).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Each USB download function command calls board_usb_init before registering the
USB gadget and board_usb_cleanup after de-registering it. On devices currently
using fasboot, musb-new is usually initialized earlier, but some other boards
might need the board_usb_init call to properly initialize musb-new.
This requires adding an argument (the USB controller index) to the fastboot
command, as it is currently done with other USB download gadget functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
|
|
In Linux USB_DEVICE() is used to declare a USB device by vendor/device ID.
We should follow the same convention in U-Boot. Rename the existing
USB_DEVICE() macro to U_BOOT_USB_DEVICE() and bring in the USB_DEVICE()
macro from Linux for use in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present USB Ethernet does not work with CONFIG_DM_ETH. Add driver model
support to this feature, so that it can work alongside other Ethernet
devices with driver model.
It was found that quite a bit of code is common in most of the USB Ethernet
drivers. Add this code to the common layer to reduce the amount of duplicate
code needed in USB Ethernet drivers when CONFIG_DM_ETH is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
If driver model is used for Ethernet then USB Ethernet does not build. This
can be made to work with driver model is used for USB also. Add #ifdef logic
to make this clear when building.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
At present all PCI devices must be present in the device tree in order to
be used. Many or most PCI devices don't require any configuration other than
that which is done automatically by U-Boot. It is inefficent to add a node
with nothing but a compatible string in order to get a device working.
Add a mechanism whereby PCI drivers can be declared along with the device
parameters they support (vendor/device/class). When no suitable driver is
found in the device tree the list of such devices is consulted to determine
the correct driver. If this also fails, then a generic driver is used as
before.
The mechanism used is very similar to that provided by Linux and the header
file defintions are copied from Linux 4.1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
On some single port (otg) controllers there is no emulated root hub, so
the first child (if any) may be one of: UCLASS_MASS_STORAGE,
UCLASS_USB_DEV_GENERIC or UCLASS_USB_HUB.
All three of these (and in the future others) are suitable for our
purposes, remove the check for the device being a hub, and add a check to
deal with the fact that there may be no child-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
last_child was abused by the old usb code to first store 1 if the
usb_device was not the root of the usb tree, and then later on re-used
to store whether or not the usb_device is actually the last child.
The dm-usb code was always setting it to actually reflect the last-child
status which is wrong for the last child leading to output like this:
USB device tree:
1 Hub (12 Mb/s, 100mA)
| ALCOR USB Hub 2.0
|
| 2 Mass Storage (12 Mb/s, 100mA)
| USB Flash Disk 4C0E960F
|
+-3 Human Interface (1.5 Mb/s, 100mA)
SINO WEALTH USB Composite Device
Instead of this:
USB device tree:
1 Hub (12 Mb/s, 100mA)
| ALCOR USB Hub 2.0
|
+-2 Mass Storage (12 Mb/s, 100mA)
| USB Flash Disk 4C0E960F
|
+-3 Human Interface (1.5 Mb/s, 100mA)
SINO WEALTH USB Composite Device
This commit fixes this by first checking that the device is not root,
and then setting last_child. This commit also updates the old code to not
abuse the last_child variable to store the root check result.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add an usb_device parameter to usb_reset_root_port so that it knows which
root-port it is resetting. This is necessary for proper device-model support
for usb_reset_root_port.
Also remove a duplicate declaration of usb_reset_root_port() from usb.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Pass the usb_device instead of the portnr to usb_legacy_port_reset and
rename it to usb_hub_port_reset as there is nothing legacy about it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Drop the unneeded portnr function argument, the portnr is part of the
usb_device struct which is passed via the dev argument.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The device-model usb_legacy_port_reset function calls the device-model
usb_port_reset function which is a 1 on 1 copy of the non dm
usb_legacy_port_reset and this is the only use of usb_port_reset in all
of u-boot.
Drop both, and alway use the usb_legacy_port_reset() version in
common/usb.c .
Also while at it make it static as it is only used in common/usb.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
As a debug option, add positive confirmation that SPL has completed
execution. This can help with diagnosing the location of unexpected hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable MMC using driver model in SPL for consistency with U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a few messages to indicate progress and failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present printf() skips output if it can see there is no console. This
is really just an optimisation, and is not necessary. Also it is currently
incorrect in some cases. Rather than update the logic, just remove it so
that we don't need to keep it in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When there is no console ready, allow the debug UART to be used for output.
This makes debugging of early code considerably easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Offer to display the available image types in help. Also, rather than
hacking the genimg_get_type_id() function to display a list of types,
do this in the tool. Also, sort the list.
The list of image types is quite long, and hard to discover. Print it out
when we show help information.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Export functions required by Aquntia PHY firmware load application.
functions are memset, strcpy, mdelay, mdio_get_current_dev,
phy_find_by_mask, mdio_phydev_for_ethname and miiphy_set_current_dev
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Commit 90fbee3e4051 ("cmd_fdt: Actually fix fdt command in sandbox")
changed the format(from hex address to unsigned long) in which "fdtaddr"
is saved . However do_fdt continues reads the "fdtaddr" assuming it to
be in hex format. This may lead to fdt being either loaded or attempted
to load at erroneous address generating fault if the address is out of
memory.
This patch changes back the format to hex while saving the "fdtaddr"
as it was done before.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hua Yanghao <huayanghao@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Avoid clearing the reg property in the memory DT node if no memory
banks have been specified for a board (CONFIG_NR_DRAM_BANKS == 0).
This allows boards to let U-Boot skip the DT memory tinkering in case
other firmware has already setup the node properly before.
This should be safe as all callers of fdt_fixup_memory_banks that use
a computed <banks> value put at least 1 in there.
Add some documentation comments to the header file.
Signed-off-by: Andre Przywara <osp@andrep.de>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Currently CONFIG_DM_I2C is used in cmd_date.c for driver model,
but it should be actually CONFIG_DM_RTC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Include <errno.h> otherwise ENOSYS is undefined.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Rather than just 'ERROR', display the error code, which may be useful, at
least with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
|
|
Commit 2b42c9317db ("ahci: support LBA48 data reads for 2+TB drives")
introduced conditional code which triggers a warning when compiled
with DEBUG enabled:
In file included from common/cmd_scsi.c:12:0:
common/cmd_scsi.c: In function 'scsi_read':
include/common.h:109:4: warning: 'smallblks' may be used uninitialized in this function [-Wmaybe-uninitialized]
...
Since this is for debug only, take the easy way and initialize the
variable explicitly on declaration to avoid the warning.
(Fix a nearby whitespace error on the way.)
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
|
|
Added Kconfig entry for CMD_SF.
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
If flash pointer is used free it, before probing a new
flash and storing it in flash.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
With this patch, it is possible to get the offset and size information
from the mtdpartiton setting in "mtdparts", similiar to the
"nand" commandos.
=> sf
sf - SPI flash sub-system
Usage:
sf probe [[bus:]cs] [hz] [mode] - init flash device on given SPI bus
and chip select
sf read addr offset|partition len - read `len' bytes starting at
`offset' to memory at `addr'
sf write addr offset|partition len - write `len' bytes from memory
at `addr' to flash at `offset'
sf erase offset|partition [+]len - erase `len' bytes from `offset'
`+len' round up `len' to block size
sf update addr offset|partition len - erase and write `len' bytes from memory
at `addr' to flash at `offset'
=>
for example "env" is defined in mtdparts:
=> sf read 13000000 env
device 0 offset 0xd0000, size 0x10000
SF: 65536 bytes @ 0xd0000 Read: OK
zynq-uboot> mtdparts add nor0 0x10000@0x0 env
zynq-uboot> sf erase env 0x10000
SF: 65536 bytes @ 0x0 Erased: OK
zynq-uboot> sf write 0x100 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Written: OK
zynq-uboot> sf read 0x40000 env
device 0 offset 0x0, size 0x10000
SF: 65536 bytes @ 0x0 Read: OK
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
