| Age | Commit message (Collapse) | Author |
|---|
|
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low(). Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
|
|
|
|
|
|
|
|
|
|
The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3. This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
Mostly putting a space between function name and "(", and
doing return (foo)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
When fdt_fixup_memory_banks is called with 2-cell address and size
fields in the device-tree (IE: 64-bit address and size), then it will
overflow its on-stack "tmp" buffer.
This fixes the buffer size and adds a comment explaining how many bytes
need to be allocated per record.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Jerry Van Baren <vanbaren@cideas.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
|
|
|
|
Make sure the pin request passed before attempting to use it later on.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The Blackfin gpio command isn't terribly Blackfin-specific. So generalize
the few pieces into two new optional helpers:
name_to_gpio() - turn a string name into a GPIO #
gpio_status() - display current pin bindings (think /proc/gpio)
Once these pieces are pulled out, we can relocate the cmd_gpio.c into the
common directory.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
There's no real need to keep these functions in the cmd_mem file since
they do not use any of the common global mem variables. So split them
out into their own dedicated cmd files.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
|
|
This patch fixes following warning message:
---8<---
cmd_bdinfo.c:458: warning: initialization from incompatible pointer type
--->8---
There was a prototype change in 54841ab50c20d6fa6c9cc3eb826989da3a22d934 for
argv[] pointer type to const. This change was not made for AVR32 cause this
code came in later by a merge.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
|
|
This patch fixes warnings in MAKEALL for avr32:
---8<---
cmd_nvedit.c: In function 'do_env_export':
cmd_nvedit.c:663: warning: format '%zX' expects type 'size_t', but argument 3 has type 'ssize_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
|
|
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
|
|
Requires a little reworking of the code flow with sub-functions, but
not a big deal.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The common spi flash layer displays useful info when probing, so no
need for us to duplicate that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch adds [+]len handler for the erase command that will
automatically round up the requested erase length to the flash's
sector_size.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
For uImage always has a 64 bytes header, we couldn't expect to do
the xip from the header but should xip from the image start.
The latter logic in that section is also move the image from image_start
to the load address, so sync this logic to the xip operation.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
|
|
Simple command to decode/check an LDR image before we try to boot it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Now that the common bootrom.h sets up defines for us, switch to them
rather than our own local set.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Conflicts:
drivers/usb/host/ehci-pci.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
On some boards the environment may not be located at a fixed address in
the MMC/SDHC card. This allows those boards to implement their own
means to report what address the environment is located at.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The reset request in usb_stor_get_info is causing issues with some usb
sticks. Some of these sticks vendor_id/product_id have been hardcoded to
not reset but better is to remove the reset altogether. It is not needed.
Signed-off-by: Erik Hansen <erik@makarta.com>
|
|
Some ubi commands returned negative error codes, resulting in
the following error message on the prompt:
"exit not allowed from main input shell."
Negative error codes are not allowed.
This patch now changes the UBI code to return positive error codes.
Additionally "better" error codes are used, for example "ENOMEM" when
no memory is available for the UBI volume creation any more.
Also the output of some commands is enhanced:
Before:
=> ubi read 100000 testvol 100000
Volume testvol found at volume id 0
read 1048576 bytes from volume 0 to 100000(buf address)
=> ubi write 100000 testvol 1000
Volume testvol found at volume id 0
After:
=> ubi read 100000 testvol 100000
Read 1048576 bytes from volume testvol to 00100000
=> ubi write 100000 testvol 1000
4096 bytes written to volume testvol
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
These variables are only used in case CONFIG_SYS_NO_FLASH is NOT set:
struct mtd_device *dev;
struct part_info *part;
u8 dev_type, dev_num, pnum;
Signed-off-by: Remy Bohmer <linux@bohmer.net>
|
|
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The unzip command did not provide a way for the caller to get any
information about the uncompressed size. To make it better usable in
scripts, we now store the uncompressed size in the `filesize'
variable, like we do when for example loading a file over the network
or when reading it from a file system. Following that analogy, it is
only consequent to also print the size.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The implementation of the string compare function of the "itest"
command was weird, as only the length of the shortest argument was
included in the compare, with the result that something like
"itest.s abd == abddef" would return TRUE. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
|
|
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
|
|
Previously, uninitialized stack space was being referenced.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
While debugging some USB stuff, I've first missed that there are actually
two defines necessary to get usefull output. The one needed to get debug output
for the communication with HUBs was burried somewhere deep inside the code.
Change that so that a #define DEBUG is enough while still leaving the possibility
to reduce unwanted debug output.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
|
|
I currently don't know if the error could have other consequences
than a wrong output when turning debug on.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
|
|
commit 8bde63eb3f79d68f693201528dafc8ae7aa087de ([MIPS] Rename Alchemy
processor configs into CONFIG_SOC_*) forgot to pick up this one.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
|
|
When redundand environments are used the serial needs
to get increased, otherwise the old one will still be used.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
After years of unsuccessful research I've finally shamelessly stolen other
peoples intellectual properties to present the all-new and world-changing
updated version command:
-
U-Boot>> version
U-Boot 2010.12-00014-g7435056-dirty (Jan 18 2011 - 23:19:38)
MyBoard
gcc (GCC) 0.42 (Distro foobar)
GNU ld (GNU Binutils) 0.314159265
-
May the toolchain bugs rest in peace.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
|
