| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.
However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.
Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
|
|
This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
Move the SPL settings into common/spl where most of the SPL code is kept.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Update the config.h and defconfig files for the commands that 8e3c036
converted over to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This syncs up the current cmd/Kconfig and include/configs/ files with the
only exception being CMD_NAND. Due to how we have used this historically
we need to take further care here when converting.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove
all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.
Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.
This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Select SYS_NS16550 from Kconfig instead of setting it in all our
defconfig files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
|
|
Add CMD_GPIO to Kconfig and run tools/moveconfig.py .
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
|
|
Now that the device-model port of the musb mode makes it possible, enable
both the ehci and otg in host mode on boards where the musb is wired up in
host only mode, either via an usb-a receptacle or via an usb <-> sata
converter.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
With certain features being convert to DM now we want sunxi to default
to having DM enabled for ETH/SERIAL and USB in some cases.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Rini <trini@konsulko.com>
[hdegoede@redhat.com: Also select CONFIG_USB for all sunxi builds]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Select CONFIG_CMD_NET and CONFIG_CMD_SETEXPR by default rather then
needing to have this in every sunxi defconfig file.
This also fixes the Merrii_A80_Optimus defconfig no longer building.
Cc: Maxin B. John <maxin.john@enea.com>
Reported-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
In order to reduce merge conflicts and to maintain the simplest possible
defconfig files, we should be using the savedefconfig feature of Kconfig
every time a new feature is added. This keeps the defconfig settings to
a minimum (only those things not default) and keeps them in the same
order as the Kconfig options.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
Now that we've everything prepared for it remove the DM settings from the
defconfig(s) and simply always set them for sunxi.
This makes all sunxi boards allways use the driver model for gpios and
ethernet, and allows us to move over more bits to the driver-model without
the need to introduce #ifdef-ery for boards which are not yet using DM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
This is a preparation patch for switching all sunxi boards over to using
the driver model.
Note that rather then defining both CONFIG_DEFAULT_DEVICE_TREE (for u-boot)
and CONFIG_FDTFILE (for the kernel), this commit simply replaces all
CONFIG_FDTFILE defconfig settings with CONFIG_DEFAULT_DEVICE_TREE and
uses CONFIG_DEFAULT_DEVICE_TREE for setting the default fdtfile env value
in sunxi-common.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Since commit e02ee2548afe (kconfig: switch to single .config
configuration), the prefixes in defconfig files such as "+S:",
"+ST:", etc., are meaningless.
This commit was generated by the following command:
find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Some of the ldo-s of the axp221 are used in the same way on most boards, add
comments to the Kconfig help text to reflect this, and give them defaults
matching their typical usage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out:
http://www.geekbuying.com/item/CS908-Allwinner-A31S-Quad-Core-1-2GHz-Android-4-4-Mini-TV-Box-HDMI-HDD-Player-1G-8G-WIFI-Miracast---Black-333395.html
Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
